Steam and gas turbines
Steam and gas turbines: principles, ideal/real cycle analysis (Rankine, Brayton), component isentropic efficiencies, Euler turbine work, nozzles and choked flow, reheat/regeneration basics, and typical exam numericals.
Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.
Why it matters
Steam and gas turbines are the core of large-scale power generation (thermal power plants, combined cycles) and aircraft propulsion. Understanding their thermodynamics lets you estimate power, efficiency, and how design choices like pressure ratio, reheat and regeneration improve performance.
Key ideas
- Turbine (steady-flow device): A device that produces shaft work by expanding a working fluid from high to low pressure at (typically) steady state. For analysis, we use the Steady-Flow Energy Equation (SFEE) with appropriate assumptions.
- Steam turbine vs. gas turbine: Steam turbines operate in a vapor power cycle (Rankine family); gas turbines operate in a gas power cycle (Brayton family). Steam properties come from steam tables (non-ideal real fluid), while gas turbines are often modeled as ideal gases with constant or temperature-dependent specific heats.
- Impulse turbine (steam): Pressure drop occurs only in nozzles (stator); rotor ideally sees only change in fluid direction (no static pressure change). The classic Curtis/Rateau stages use impulse compounding.
- Reaction turbine (steam): Pressure drop is shared between stator and rotor; rotor passages act like moving nozzles. The classic Parson’s stage is approximately 50% reaction under symmetry assumptions.
- Euler turbine equation: For an axial turbomachine stage, specific work transfer equals the change in swirl (tangential) momentum: w = U (Vw1 − Vw2). Here U is blade speed (tangential), Vw is absolute whirl component (+ in direction of wheel rotation), subscripts 1 and 2 denote inlet to and exit from the rotor.
- Velocity triangles (angles): Absolute velocity V makes an angle α with the wheel tangent; relative velocity W (as seen by the blade) makes an angle β with the wheel tangent. Components: Vw = V cos α (tangential), Vx = V sin α (axial). Keep the sign convention explicit (positive whirl in blade rotation direction).
- Nozzle (adiabatic expansion): Converts stagnation enthalpy into kinetic energy. For ideal gas with isentropic flow, critical pressure ratio exists beyond which the flow chokes (Mach 1 at throat). For steam, use steam tables or validated correlations; ideal-gas critical relations are not generally accurate.
- Isentropic efficiency (component): Compares actual device performance with an internally reversible (adiabatic, no internal irreversibility) reference between the same inlet and exit pressure(s).
- Isentropic turbine efficiency (η_t): η_t = (actual specific work)/(isentropic specific work) = (h_in − h_out)/(h_in − h_out,s).
- Isentropic compressor efficiency (η_c): η_c = (isentropic specific work)/(actual specific work) = (h_out,s − h_in)/(h_out − h_in).
- Nozzle efficiency (η_n): η_n = (actual exit KE per unit mass)/(isentropic enthalpy drop) = (V_2^2/2)/(h_0,in − h_out,s).
- Polytropic efficiency (small-stage efficiency): For compressors/turbines treated as many small stages, η_poly relates the actual differential process to an isentropic one. For ideal gases with a polytropic exponent n, T–p relation is T2/T1 = (p2/p1)^((n−1)/n). Polytropic efficiency ties n to γ but requires careful assumptions.
- Rankine cycle (steam power cycle): Boiler (or steam generator), turbine, condenser, and pump. Heat addition at (nearly) constant pressure in the boiler; expansion through the turbine; heat rejection in the condenser; compression (liquid) by pump. Variants: reheat and regeneration to improve efficiency and/or limit turbine exhaust moisture.
- Reheat Rankine: Partially expand in HP turbine, reheat at (approximately) constant pressure, then expand in LP turbine. Increases average temperature of heat addition and reduces moisture at final stages.
- Regeneration (feedwater heating): Diverts some steam to heat feedwater, raising the mean temperature of heat addition and improving cycle efficiency.
- Moisture limit at turbine exit: Excessive wetness increases erosion; designs generally aim for a sufficiently high dryness fraction (typical design aim: x ≳ 0.88–0.9), often achieved by reheat/regeneration.
- Brayton cycle (gas turbine power cycle): Compressor, combustor (heat addition at essentially constant pressure), turbine, exhaust. For ideal gas with constant γ, closed-form efficiency expressions exist; for real engines, component efficiencies and pressure losses are included.
- Pressure ratio (r_p): Ratio of compressor exit to inlet pressure. In the ideal Brayton cycle (constant γ, fixed Tmin and Tmax), there is an r_p that maximizes specific work: r_p,opt = (T3/T1)^(γ/(2(γ−1))). Thermal efficiency for the ideal cycle: η = 1 − 1/r_p^((γ−1)/γ).
- Regeneration in Brayton: A counterflow heat exchanger (recuperator) preheats compressor exit air using turbine exhaust, reducing required heat addition. Effectiveness ε = (actual temperature rise of compressed air)/(maximum possible using turbine exhaust).
- Sign conventions (thermodynamics of control volumes): Heat transfer to the working fluid is positive. Turbine work output is positive (work done by the system), compressor/pump work input is negative (work done on the system). Absolute whirl positive in direction of rotor motion for Euler equation.
- Why real devices differ from ideal: Irreversibilities (fluid friction, shock and mixing losses, heat transfer across finite ΔT, leakage, tip-clearance), non-isentropic compression/expansion, pressure drops in ducts/heat exchangers, finite mechanical efficiencies. In steam systems, non-ideal fluid behavior demands accurate properties (steam tables/IAPWS). In gas turbines, γ and c_p vary with temperature; modeling with constant properties introduces error at high TIT.
Formulas
SFEE (steady turbine/compressor, adiabatic, negligible PE change): ẇ = ṁ·w = ṁ·[(h_in − h_out) + (V_in² − V_out²)/2]
- ẇ: shaft power (W), ṁ: mass flow (kg/s), w: specific work (J/kg). Applies to adiabatic steady devices; include KE terms if significant.
Euler turbine equation: w = U·(Vw1 − Vw2)
- w: specific work (J/kg), U: blade speed at mean radius (m/s), Vw1, Vw2: inlet and exit absolute whirl components (m/s). Sign per defined whirl direction; applies to turbomachinery stages, neglecting radial work terms for axial machines.
Isentropic turbine efficiency: η_t = (h_in − h_out)/(h_in − h_out,s)
- h: specific enthalpy (kJ/kg). Applies to an adiabatic turbine between the same inlet state and exit pressure; s denotes isentropic exit at same p_out.
Isentropic compressor efficiency: η_c = (h_out,s − h_in)/(h_out − h_in)
- Applies to an adiabatic compressor between same inlet and exit pressure.
Nozzle efficiency: η_n = (V_2²/2)/(h_0,in − h_out,s)
- V_2: actual exit speed (m/s), h_0,in: inlet stagnation enthalpy (kJ/kg), h_out,s: isentropic exit enthalpy at same p_out. Applies to adiabatic nozzles.
Ideal-gas isentropic T−p relation: T2/T1 = (p2/p1)^((γ−1)/γ)
- T: absolute temperature (K), p: pressure (Pa), γ = c_p/c_v (−). Applies to ideal gases with constant γ in isentropic flow.
Ideal-gas compressor/turbine specific work (isentropic): w_c,s = c_p·(T2,s − T1), w_t,s = c_p·(T3 − T4,s)
- c_p: specific heat at constant pressure (kJ/kg·K). Applies to ideal gases with constant c_p; adjust for variable c_p when needed.
Brayton (ideal) thermal efficiency: η_th = 1 − 1/r_p^((γ−1)/γ)
- r_p = p2/p1 (compressor pressure ratio). Ideal-gas, isentropic compressor/turbine, no pressure losses, constant γ.
Brayton (ideal) specific net work: w_net = c_p·[(T3 − T4) − (T2 − T1)]
- For ideal-gas cycle with isentropic compression/expansion; T4 = T3/r_p^((γ−1)/γ), T2 = T1·r_p^((γ−1)/γ).
Optimum pressure ratio for maximum specific work (ideal Brayton): r_p,opt = (T3/T1)^(γ/(2(γ−1)))
- Applies for ideal-gas Brayton, fixed Tmin = T1 and Tmax = T3, isentropic components, no regenerator.
Critical pressure ratio (ideal-gas nozzle): (p*/p0) = (2/(γ+1))^(γ/(γ−1))
- p*: sonic (throat) static pressure, p0: inlet stagnation pressure. Ideal-gas, isentropic, 1-D nozzle.
Rankine cycle thermal efficiency (per unit mass of steam): η_th = [(h3 − h4) − (h2 − h1)]/(h3 − h2)
- 1→2: pump, 2→3: boiler, 3→4: turbine, 4→1: condenser. h from steam tables (kJ/kg). Assumes negligible KE/PE changes.
Pump work (approximate, incompressible): w_p ≈ v·(p_boiler − p_cond)
- v: specific volume of saturated liquid at condenser outlet (m³/kg), pressures in Pa; w_p in J/kg. Good approximation since liquid is nearly incompressible.
Specific steam consumption (SSC): SSC = 3600 / w_net
- SSC (kg/kWh), w_net: net specific work of cycle (kJ/kg). Simple energy accounting.
Regenerator effectiveness (Brayton): ε = (T5 − T2)/(T4 − T2)
- T5: compressor-exit air temperature after regenerator, T2: compressor exit before regenerator, T4: turbine exit before regenerator. Ideal counterflow definitions.
Worked examples
Example 1 (direct, ideal Brayton): Net work and efficiency of a simple gas turbine Given: Ideal Brayton cycle (air-standard), T1 = 300 K, p1 arbitrary (cancels), pressure ratio r_p = 8, γ = 1.4, c_p = 1.004 kJ/kg·K, turbine inlet temperature T3 = 1200 K. Assume isentropic compressor and turbine, no pressure losses.
Steps:
Compressor exit temperature (isentropic): Formula: T2 = T1·r_p^((γ−1)/γ) Numbers: T2 = 300 K × 8^(0.4/1.4) = 300 × 8^0.285714 ≈ 300 × 1.811 = 543.3 K
Turbine exit temperature (isentropic): Formula: T4 = T3 / r_p^((γ−1)/γ) Numbers: T4 = 1200 K / 1.811 = 662.9 K
Specific turbine work and compressor work: Formulas: w_t = c_p·(T3 − T4), w_c = c_p·(T2 − T1) Numbers: w_t = 1.004 × (1200 − 662.9) = 1.004 × 537.1 = 539.2 kJ/kg w_c = 1.004 × (543.3 − 300) = 1.004 × 243.3 = 244.3 kJ/kg
Net specific work and heat added: Formulas: w_net = w_t − w_c, q_in = c_p·(T3 − T2) Numbers: w_net = 539.2 − 244.3 = 294.9 kJ/kg q_in = 1.004 × (1200 − 543.3) = 1.004 × 656.7 = 659.3 kJ/kg
Thermal efficiency: Formula: η_th = w_net / q_in Numbers: η_th = 294.9 / 659.3 = 0.4476 = 44.8%
Answer: Net specific work = 294.9 kJ/kg, thermal efficiency = 44.8%.
Example 2 (GATE-style, combining Euler work and velocity triangles): Single axial turbine stage power and inlet blade angle Given: An axial turbine stage has constant axial velocity Vx = 150 m/s through the rotor. Blade speed U = 250 m/s. Absolute inlet flow angle α1 = 20° to the wheel tangent (positive with rotation). Absolute exit flow angle α2 = −60° (negative whirl, i.e., opposite the rotation at exit). Mass flow rate ṁ = 5.0 kg/s. Assume adiabatic stage, negligible losses for kinematics (use Euler to get work). Find (a) specific work output, (b) shaft power, (c) rotor inlet relative flow angle β1.
Assumptions and relations:
- Components: Vw = V cos α (tangential), Vx = V sin α (axial). Given Vx constant, we can get Vw from α.
- Euler work: w = U (Vw1 − Vw2), with positive whirl in direction of rotation.
- Relative inlet tangential component: Ww1 = Vw1 − U (since W = V − U in tangential direction for the rotor at inlet). Then tan β1 = Vx / Ww1.
Steps:
Compute whirl components from given Vx and α at inlet and exit: Formulas: Vw1 = Vx·cot α1, Vw2 = Vx·cot α2 Numbers: cot 20° ≈ 2.747, cot (−60°) = −cot 60° = −0.57735 Vw1 = 150 × 2.747 = 412.1 m/s Vw2 = 150 × (−0.57735) = −86.60 m/s
Specific work from Euler: Formula: w = U·(Vw1 − Vw2) Numbers: w = 250 × (412.1 − (−86.6)) = 250 × 498.7 = 124,675 W/kg = 124.68 kJ/kg
Shaft power for given mass flow: Formula: P = ṁ·w Numbers: P = 5.0 kg/s × 124,675 W/kg = 623,375 W = 623.4 kW
Rotor inlet relative angle β1: Intermediate: Ww1 = Vw1 − U = 412.1 − 250 = 162.1 m/s Formula: tan β1 = Vx / Ww1 Numbers: tan β1 = 150 / 162.1 = 0.9256 ⇒ β1 = arctan(0.9256) = 42.9° (to the wheel tangent)
Optional checks:
- Inlet absolute speed magnitude V1 = √(Vw1² + Vx²) = √(412.1² + 150²) = √(169,826.4 + 22,500) = √192,326.4 = 438.5 m/s (not required, consistent with the triangles).
Answers: (a) Specific work = 124.68 kJ/kg, (b) Power = 623.4 kW, (c) β1 = 42.9°.
Common mistakes
- Mixing up angles and components in velocity triangles (e.g., taking α with respect to axial instead of tangential without stating it). Always define your convention first.
- Using ideal-gas isentropic relations for steam expansions. For steam, use steam tables/IAPWS correlations; only use ideal-gas formulas for gases near ideal behavior.
- Dropping kinetic energy terms in SFEE when nozzles or very high stage loadings are involved; KE terms matter in nozzles and sometimes at turbine exhausts.
- Confusing isentropic and polytropic efficiencies, or inverting compressor/turbine efficiency definitions.
- Ignoring pump work in Rankine cycle calculations. It is small but not always negligible when precision is needed; use vΔp.
- Assuming Brayton cycle efficiency depends only on temperatures without recognizing the pressure ratio dependence (η_th = 1 − 1/r_p^((γ−1)/γ) for ideal gas with constant γ).
- Forgetting pressure losses and regenerator effectiveness limits in real gas turbines; overpredicting performance.
For GATE ME
- Conceptual and numerical questions on Rankine and Brayton cycles: compute efficiency, specific work, back work ratio, mass flow for given power.
- Component isentropic efficiency problems: given inlet/outlet pressures and efficiencies, find actual exit temperatures/enthalpies (gas turbines via ideal-gas relations, steam turbines via tables).
- Effects of reheat and regeneration: compare efficiencies, find reheat pressure for given constraints, compute regenerator outlet temperatures given effectiveness.
- Euler turbine stage work using velocity triangles: compute specific work, blade angles, and sometimes axial velocity or mass flow for target power.
- Nozzle flow and choking: determine whether choked, compute critical pressure ratio and exit velocity for ideal-gas nozzles; caution with steam.
- Practise: set up state points clearly, write governing relations first, carry units, and check limiting cases (e.g., η→1 recovers isentropic results; r_p→1 gives zero Brayton net work).
Quick check
- State the Euler turbine equation and define each term.
- In an ideal Brayton cycle with γ constant, how does thermal efficiency depend on compressor pressure ratio?
- Write the expression for isentropic turbine efficiency and explain how you would find h_out,s for a steam turbine.
Answers: 1) w = U·(Vw1 − Vw2); w is specific work (J/kg), U blade speed (m/s), Vw1/Vw2 inlet/exit whirl (m/s). 2) η_th = 1 − 1/r_p^((γ−1)/γ); it increases with r_p for fixed γ (up to TIT constraints). 3) η_t = (h_in − h_out)/(h_in − h_out,s); find h_out,s by isentropic expansion to the same p_out (ideal gas via isentropic T–p, steam via steam tables at s_out = s_in and p_out).
Finished this topic? Mark it so your progress, study plan and readiness keep up.
Stuck on something here?