IC engine performance

IC engine performance: power (indicated/brake), mean effective pressures, efficiencies (thermal, mechanical, volumetric), specific fuel consumption, testing (dynamometers, Morse test, Willans line), heat balance, and why real engines deviate from ideal cycles.

Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.

Why it matters

Internal combustion (IC) engine performance metrics let you predict power, fuel economy, and emissions for vehicles, generators, and pumps. Knowing how to measure brake power, efficiencies, and losses helps in design, diagnosis, and improvement under real operating conditions.

Key ideas

  • Indicated work (per cycle): The net work done on the piston during one thermodynamic cycle, found from the indicator (p–V) diagram. The constant pressure that, if it acted over the swept volume, would produce the same work is the indicated mean effective pressure (imep).
  • Brake work and torque: The useful work/torque measured at the crankshaft by a dynamometer gives brake power (BP). Torque T comes from load cells, brakes, or dynamometers; BP ties torque to speed.
  • Friction power (FP): The difference between indicated and brake powers, FP = IP − BP, covering mechanical friction, pumping losses, accessory loads, and windage at the tested speed.
  • Mechanical efficiency (η_mech): Fraction of indicated power delivered as brake power, η_mech = BP/IP.
  • Thermal efficiencies:
    • Indicated thermal efficiency (η_i,th): IP divided by chemical energy rate in the fuel (ṁ_f × LHV).
    • Brake thermal efficiency (η_b,th): BP divided by fuel energy rate.
  • Specific fuel consumption (SFC):
    • Brake SFC (bsfc): Fuel mass flow per brake power; common unit kg/kWh (or g/kWh). Lower bsfc means better fuel economy.
    • Indicated SFC (isfc): Fuel per indicated power.
  • Mean effective pressures (MEP):
    • imep: Defined above from the indicator diagram; a size- and speed-independent measure of net cycle work per unit displacement that increases with load (i.e., it is a good load indicator and is independent of engine size and speed).
    • brake MEP (bmep): A convenient, speed-independent “load” metric normalizing torque to displacement (for a given engine and cycle type, bmep is directly proportional to torque and independent of speed).
    • In general, imep ≥ bmep; the gap is friction and pumping.
  • Displacement flow (V̇d): For a multi-cylinder engine, V̇d = (total swept volume per cycle) × (cycles per second). For a 4‑stroke, one cycle per 2 revolutions; for a 2‑stroke, one cycle per revolution.
  • Volumetric efficiency (η_v): The ratio of the mass (or volume at ambient conditions) of fresh charge actually inducted to that which would fill the displacement volume at ambient conditions. It reflects breathing capability; affected by intake restrictions, temperature rise, valve timing, and boosting.
  • Lower heating value (LHV) vs higher heating value (HHV): For IC engines with water vapor leaving in exhaust, use LHV (water remains vapor). Use the value given in the problem if specified.
  • Dynamometers:
    • Absorption types (Prony brake, rope brake, eddy current, hydraulic) dissipate power while measuring torque.
    • Torsion/strain-gauge types measure torque without significant power absorption.
  • Morse test (multi-cylinder SI engines): A method to estimate FP at a given speed by successively disabling one cylinder and observing the drop in BP. Assumes FP and speed are unchanged during disablements.
  • Willans line method: At constant speed, plot BP versus fuel rate; extrapolate linearly to zero fuel rate to obtain the friction power as the negative BP-axis intercept. Assumes indicated thermal efficiency is approximately constant with load at fixed speed and FP is roughly load-independent.
  • Heat balance (energy balance): The fuel’s chemical energy splits into brake work, cooling-system heat, exhaust enthalpy, and unaccounted heat (radiation, convection, oil, etc.). A “heat balance sheet” quantifies these parts at a test point.
  • Sign conventions and assumptions:
    • Pressures in Pa (positive for compression/expansion pressures).
    • Work and power are positive in the output direction at the shaft.
    • Fuel flow into the engine is positive.
    • imep and bmep are cycle-averaged, hypothetical constant pressures.
    • Willans line: speed fixed; FP ≈ constant over load; η_i,th ≈ constant over moderate loads.
    • Morse test: friction and speed are unchanged when a cylinder is cut; other cylinders’ indicated powers are unaffected.
  • Standard/limiting cases:
    • 4‑stroke engines have one power stroke per cylinder every two crank revolutions (lower displacement flow at a given rpm than 2‑stroke).
    • Naturally aspirated full-load volumetric efficiency typically ~0.75–0.95; supercharged/turbocharged can exceed 1.0 (since referred to ambient conditions).
    • Typical full-load bmep values: SI ~8–12 bar; CI ~10–14+ bar (varies by design and speed).
    • Typical bsfc ranges (modern engines, approximate): SI ~240–320 g/kWh; CI ~180–260 g/kWh.
  • Why real engines differ from air-standard cycles: Time‑dependent combustion, heat transfer to walls, gas exchange (pumping) losses, finite burn duration, throttling (SI part-load), friction, mixture formation issues, and exhaust backpressure reduce imep and η_th from ideal predictions.

Formulas

W_i,cycle = p_i · V_s

  • Indicated work per cycle equals imep times swept volume per cylinder. p_i: indicated mean effective pressure (Pa), V_s: swept volume per cylinder (m³). Applies to any reciprocating engine cycle.

IP = p_i · V̇_d

  • Indicated power equals imep times displacement flow rate. V̇_d: displacement flow rate (m³/s) = total swept volume per cycle × cycles per second. IP in W. Valid when imep is defined for the same operating point.

V̇_d (4‑stroke) = V_s,total · (N_rpm / 2) / 60

  • Displacement flow for a 4‑stroke engine. V_s,total: total swept volume of all cylinders (m³), N_rpm: speed in rpm. Units: m³/s.

V̇_d (2‑stroke) = V_s,total · (N_rpm / 60)

  • Displacement flow for a 2‑stroke engine. Units: m³/s.

BP = 2π · N_rps · T = (2π · N_rpm · T) / 60

  • Brake power from torque. T: torque (N·m), N_rps: rev/s, N_rpm: rev/min. BP in W.

η_mech = BP / IP

  • Mechanical efficiency. Dimensionless. Applies at the same speed/load.

η_i,th = IP / (ṁ_f · LHV)

  • Indicated thermal efficiency. ṁ_f: fuel mass flow (kg/s), LHV: lower heating value (J/kg). Dimensionless.

η_b,th = BP / (ṁ_f · LHV)

  • Brake thermal efficiency. Dimensionless.

bsfc (kg/kWh) = 3600 · ṁ_f (kg/s) / BP (kW)

  • Brake specific fuel consumption. For g/kWh, multiply by 1000.

isfc (kg/kWh) = 3600 · ṁ_f (kg/s) / IP (kW)

  • Indicated specific fuel consumption.

bmep = BP / V̇_d

  • Brake mean effective pressure. BP in W, V̇_d in m³/s → bmep in Pa.

imep = IP / V̇_d

  • Indicated mean effective pressure. IP in W, V̇_d in m³/s → imep in Pa.

bmep (4‑stroke) = (4π · T) / V_s,total

  • Direct bmep–torque relation for 4‑stroke engines. T in N·m, V_s,total in m³ → bmep in Pa.

T (4‑stroke) = (bmep · V_s,total) / (4π)

  • Torque from bmep for 4‑stroke engines.

bmep (2‑stroke) = (2π · T) / V_s,total

  • Direct bmep–torque relation for 2‑stroke engines.

T (2‑stroke) = (bmep · V_s,total) / (2π)

  • Torque from bmep for 2‑stroke engines.

η_v = (ṁ_a · R · T_1) / (p_1 · V̇_d)

  • Volumetric efficiency using mass flow. ṁ_a: air (or fresh charge) mass flow (kg/s), R: specific gas constant of air ≈ 287 J/kg·K, T_1 and p_1: intake (ambient/reference) temperature (K) and pressure (Pa). Dimensionless. For boosted engines, use the intake manifold p–T.

C_m = 2 · L · N_rps = (2 · L · N_rpm)/60

  • Mean piston speed. L: stroke (m). Units: m/s.

BP (rope brake) = 2π · N_rps · (W − S) · R

  • Rope brake dynamometer. W: dead weight (N), S: spring balance reading (N), R: effective radius to rope centerline (m). BP in W. Assumes steady friction and no buoyancy correction.

Morse test (per cut) : ΔBP_i ≈ IP_i ; FP ≈ (Σ ΔBP_i) − BP_full

  • For a multi-cylinder engine at fixed speed. ΔBP_i: drop in brake power on cutting cylinder i, IP_i: indicated power of cylinder i, BP_full: brake power with all cylinders firing. Assumes FP constant and speed unchanged when cutting.

Fuel energy balance: ṁ_f · LHV = BP + Q_cooling + Q_exhaust + Q_unaccounted

  • Steady-state heat balance. Q terms are power (W). Q_unaccounted covers radiation, convection, oil, etc.

Worked examples

Example 1 — Direct application (single-cylinder IP, BP, η_mech) Given: Single-cylinder, 4‑stroke engine; bore d = 100 mm, stroke L = 120 mm; speed N = 1500 rpm; indicated mean effective pressure p_i = 8 bar; measured brake torque T = 45 N·m. Assume: SI units; steady state; atmospheric conditions not needed here.

  1. Swept volume per cylinder
  • Formula: V_s = (π/4) · d² · L
  • Numbers: V_s = (π/4) · (0.1 m)² · 0.12 m = 9.4248×10⁻⁴ m³
  1. Displacement flow (4‑stroke)
  • Formula: V̇_d = V_s · (N_rpm/2)/60
  • Numbers: V̇_d = 9.4248×10⁻⁴ · (1500/2)/60 = 9.4248×10⁻⁴ · 12.5 = 0.011781 m³/s
  1. Indicated power
  • Formula: IP = p_i · V̇_d
  • Numbers: IP = (8.0×10⁵ Pa) · 0.011781 m³/s = 9.425×10³ W = 9.425 kW
  1. Brake power
  • Formula: BP = 2π · N_rps · T, with N_rps = N_rpm/60
  • Numbers: N_rps = 1500/60 = 25 s⁻¹; BP = 2π · 25 · 45 = 7068.6 W = 7.069 kW
  1. Mechanical efficiency
  • Formula: η_mech = BP/IP
  • Numbers: η_mech = 7.069 / 9.425 = 0.750

Final answers: IP = 9.425 kW, BP = 7.069 kW, η_mech = 0.750 (75.0%).

Example 2 — GATE-level combined (Willans line, FP, efficiencies, MEP) Given: A 4‑cylinder, 4‑stroke engine, bore d = 80 mm, stroke L = 100 mm, speed N = 3000 rpm. Two steady test points at this speed:

  • Point A: BP₁ = 18 kW at fuel rate ṁ_f1 = 4.0 kg/h
  • Point B: BP₂ = 36 kW at fuel rate ṁ_f2 = 6.8 kg/h Fuel LHV = 43 MJ/kg. Assume: Willans line applicable at this speed (linear BP–ṁ_f), FP ≈ constant with load. SI units.
  1. Determine Willans line (BP vs ṁ_f) and friction power FP
  • Model: BP = a · ṁ_f + b, with b = −FP (at zero fuel, BP = −FP)
  • Slope a = (BP₂ − BP₁) / (ṁ_f2 − ṁ_f1) = (36 − 18) kW / (6.8 − 4.0) kg/h = 18 / 2.8 = 6.4286 kW/(kg/h)
  • Intercept b from Point A: b = BP₁ − a · ṁ_f1 = 18 − 6.4286 · 4.0 = −7.714 kW
  • Therefore FP = −b = 7.714 kW
  1. At BP = 36 kW, compute indicated power and mechanical efficiency
  • Formula: IP = BP + FP
  • Numbers: IP = 36.000 + 7.714 = 43.714 kW
  • Mechanical efficiency: η_mech = BP/IP = 36.000 / 43.714 = 0.823
  1. Thermal efficiencies at BP = 36 kW
  • Fuel rate: ṁ_f = 6.8 kg/h = 6.8/3600 = 0.0018889 kg/s
  • Fuel energy rate: ṁ_f · LHV = 0.0018889 · 43×10⁶ = 81.222 kW
  • Brake thermal efficiency: η_b,th = BP/(ṁ_f LHV) = 36.000 / 81.222 = 0.443
  • Indicated thermal efficiency: η_i,th = IP/(ṁ_f LHV) = 43.714 / 81.222 = 0.538
  1. bmep and imep at BP = 36 kW
  • Total swept volume per cylinder: V_s,cyl = (π/4) · d² · L = (π/4)·(0.08)²·0.10 = 5.0266×10⁻⁴ m³
  • Total swept volume (4 cylinders): V_s,total = 4 · 5.0266×10⁻⁴ = 0.0020106 m³
  • Displacement flow (4‑stroke): V̇_d = V_s,total · (N_rpm/2)/60 = 0.0020106 · (3000/2)/60 = 0.0020106 · 25 = 0.050265 m³/s
  • bmep = BP/V̇_d = 36,000 / 0.050265 = 7.162×10⁵ Pa = 7.16 bar
  • imep = IP/V̇_d = 43,714 / 0.050265 = 8.694×10⁵ Pa = 8.69 bar

Final answers: FP = 7.714 kW; at BP = 36 kW: IP = 43.714 kW, η_mech = 0.823, η_b,th = 0.443, η_i,th = 0.538, bmep = 7.16 bar, imep = 8.69 bar.

Common mistakes

  • Using 4‑stroke displacement flow formula for a 2‑stroke (or vice versa), leading to a factor-of-two error in power/MEP.
  • Confusing imep with bmep; using IP with bmep or BP with imep inconsistently.
  • Calculating bsfc in kg/s per kW and not converting to kg/kWh (multiply by 3600).
  • Using HHV instead of LHV for engine thermal efficiency (unless the problem specifies HHV).
  • In Morse test, assuming FP changes when a cylinder is cut, or allowing speed to vary significantly; both break the method’s assumptions.
  • In Willans line, plotting ṁ_f vs BP but interpreting the intercept incorrectly; the BP vs ṁ_f line’s BP-axis intercept is −FP at that speed.
  • Forgetting to use total swept volume (all cylinders) in V̇_d and MEP calculations.
  • Not carrying units through belt/rope brake formulas (confusing kgf with N or mixing radii).

For GATE ME

  • Straight numericals: compute BP from torque and speed; compute IP from imep and displacement flow; get η_mech, η_b,th, bsfc, bmep/imep. Expect unit conversions (rpm↔rps, bar↔Pa, kg/h↔kg/s).
  • Test-based performance:
    • Morse test: given BP with all cylinders firing and BP with each cylinder cut, find FP, IP, η_mech. Sometimes assumes identical cylinders; sometimes not.
    • Willans line: given two or more (BP, ṁ_f) points at a fixed speed, find FP from intercept; then find efficiencies at a specific load.
    • Dynamometer problems: rope brake/prony brake tensions or load cell force and arm → torque → BP.
  • Heat balance questions: compute fractions of fuel energy going to brake work, cooling water, and exhaust using measured flows and temperature rises; report percentages.
  • Conceptuals: relation of bmep to torque and why bmep is a convenient, speed-independent load measure; differences between SI and CI typical bsfc/bmep; why 2‑strokes have higher specific output at same displacement and rpm.

Practise:

  • Quickly computing V̇_d for 4‑stroke vs 2‑stroke; converting between bar and Pa, rpm and rps; intercept–slope calculations for Willans line; summations for Morse test; and careful unit handling in bsfc (kg/kWh or g/kWh).

Quick check

  1. A 4‑stroke engine has V_s,total = 1.6 L and runs at 2400 rpm. What is V̇_d?
  2. Why is bmep a better comparative performance metric than BP for engines of different sizes?
  3. In a Morse test on a 4‑cylinder engine, BP_full = 60 kW. With cylinders cut in turn, the measured BPs are 45, 44, 43, and 46 kW. What are FP and IP_total?

Answers: 1) V̇_d = 0.0016 m³ · (2400/2)/60 = 0.032 m³/s. 2) It normalizes brake work to displacement flow, removing the effect of size and speed, and is proportional to torque per unit displacement. 3) Drops ΔBP: 15, 16, 17, 14 kW → IP_total ≈ 62 kW; FP = IP_total − BP_full = 2 kW.

Finished this topic? Mark it so your progress, study plan and readiness keep up.

Stuck on something here?