Liquid fuels, cracking and octane number
Definitions, processes and calculations for liquid fuels, cracking (thermal, catalytic, hydrocracking) and octane number (RON, MON, AKI), with properties, apparatus, formulas, examples, and exam tips.
Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.
Why it matters
Liquid fuels power spark-ignition (SI) engines in two-wheelers, cars and small generators, and are key feedstocks in chemical processing. Engineers must understand how to convert heavy crude fractions into high-octane gasoline using cracking and how to measure and specify octane number to avoid engine knock and ensure performance and emissions compliance.
Key ideas
Crude oil refining: The sequence of steps converting crude oil into value-added products.
- Desalting: Removal of water-soluble salts to prevent corrosion/fouling.
- Atmospheric distillation (fractional distillation): Physical separation by boiling range at ≈ 1 atm.
- Vacuum distillation: Distillation below 1 atm to reduce cracking and boiling temperature for heavy residues.
- Conversion processes: Cracking, reforming, isomerization, alkylation to improve yield and quality (e.g., octane number).
How to draw the fractional distillation column (for exam diagrams): Draw a tall vertical column with trays. From bottom to top, label: furnace (feed preheater), column bottom (residue), side draws: diesel (higher boiling), kerosene, naphtha/gasoline (lower boiling), top condenser and reflux drum. Show rising vapors and descending liquid (reflux).
Key properties of liquid fuels (definitions used in specifications):
- Density (ρ): Mass per unit volume, kg·m⁻³, affects mass flow and energy per litre.
- Viscosity (μ): Resistance to flow, Pa·s; important for fuel handling and injection.
- Flash point: Lowest temperature at which vapor above a liquid ignites momentarily on applying a flame under specified conditions. Indicates flammability hazard.
- Fire point: Lowest temperature at which vapors burn continuously for 5 s under specified test.
- Pour point: Lowest temperature at which the fuel just flows. Important in cold climates.
- Cloud point: Temperature at which wax crystals first appear in fuels containing paraffins (important for diesel).
- Aniline point: The lowest temperature at which equal volumes of aniline and the fuel are completely miscible. Lower aniline point indicates higher aromatic content (tendency to swell rubbers; index of solvency). Units: K or °C.
- These are specification tests; calorific value and coal analysis are covered in the topic “Fuels: calorific value and analysis of coal”.
Cracking: The chemical decomposition of heavy hydrocarbon molecules into lighter molecules by breaking carbon–carbon bonds, using heat (thermal cracking) and/or catalysts (catalytic cracking), often with hydrogen (hydrocracking).
- Purpose: increase gasoline yield and improve quality (octane number), and make light olefins for petrochemicals.
- Reactions involved: C–C bond scission, isomerization (rearrangement), dehydrogenation (H₂ formation), cyclization and aromatization, hydrogen transfer.
Thermal cracking: Cracking driven primarily by heat and free-radical mechanisms.
- Vapor-phase thermal cracking: higher temperature, lower pressure; liquid-phase thermal cracking: lower temperature, higher pressure to keep feed in liquid phase.
- Typical conditions (ranges widely by unit): vapor phase ≈ 600–650 °C (873–923 K), ≈ 0.1–0.5 MPa; liquid phase ≈ 425–500 °C (698–773 K), ≈ 1–7 MPa to suppress coking. Assumption: feeds are gas oils/resids; severity controls products (more olefins at higher temperature).
- Products: gasoline-range hydrocarbons, olefins (ethylene, propylene, butenes), coke, H₂; gasoline has moderate octane.
- Advantages: simple, produces olefins; limitations: lower selectivity to high-octane gasoline, more coke.
- Diagram to draw: A furnace feeding a tubular reactor, followed by a quench tower and fractionator. Label temperatures, pressure, and product draws (gas, gasoline, gas oil, residue). Common industrial thermal processes include visbreaking (mild thermal cracking to reduce viscosity of resid) and coking (delayed or fluid coking) that produce lighter products and petroleum coke.
Catalytic cracking: Cracking using acid catalysts to promote carbocation mechanisms; higher gasoline yield and octane, less coke than thermal at similar conversion.
- Industrially, Fluid Catalytic Cracking (FCC) is dominant.
- Catalyst: acidic zeolites (e.g., faujasite-type Zeolite Y) supported on silica–alumina; particle size ≈ 50–100 μm (fluidizable).
- Conditions: ≈ 450–550 °C (723–823 K) in the riser reactor; pressure slightly above atmospheric (≈ 0.15–0.3 MPa total) to move vapors. Short residence time (seconds). Catalyst-to-oil ratio adjusted to control severity.
- Operation: powdered catalyst carries cracking reactions in a riser; spent catalyst is regenerated by burning coke in air; heat from regeneration drives endothermic cracking.
- Products: gasoline with high octane (due to isoparaffins and aromatics), LPG rich in propylene/butenes, light cycle oil, slurry oil.
- Fixed-bed/moving-bed units (older): e.g., Houdry process (fixed-bed) and Thermofor (moving-bed); now largely replaced by FCC.
- Diagram to draw: FCC unit with a vertical riser (reactor) carrying upflowing oil vapor and catalyst from the regenerator; cyclones at top to separate catalyst; a stripper; a separate regenerator vessel with air inlet and flue gas outlet; main fractionator receiving reactor effluent. Clearly label reactor, regenerator, cyclones, stripper, fractionator, catalyst circulation loop, and product draws.
- Industrially, Fluid Catalytic Cracking (FCC) is dominant.
Hydrocracking: Catalytic cracking in the presence of hydrogen.
- Catalysts: bifunctional—acidic support (zeolite or amorphous silica–alumina) plus hydrogenation–dehydrogenation metals (e.g., Ni–Mo, Co–Mo sulfides, or noble metals like Pt).
- Conditions: ≈ 350–450 °C (623–723 K); high total pressure ≈ 7–20 MPa with substantial H₂ partial pressure to suppress coke and saturate aromatics/olefins.
- Products: very clean fuels (low sulfur), high middle-distillate (jet, diesel) or high-octane naphtha depending on catalyst/severity; produces H₂-rich gas recycle.
- Advantages: handles difficult feeds (resids, heavy gas oils), low coke, desulfurization.
Reaction pathways (simplified, for conceptual understanding):
- Thermal cracking: free-radical chain reactions—initiation (C–C homolysis), propagation (β-scission, hydrogen abstraction), termination (radical recombination). Favours formation of olefins at high temperature.
- Catalytic cracking: carbocation mechanism—protonation of hydrocarbons on acid sites, β-scission of carbocations, hydride transfer (forms isoparaffins and naphthenes), cyclization/aromatization. Branching and aromatics increase in gasoline fraction.
Knocking (in SI engines): Abnormal combustion characterized by auto-ignition of end-gas ahead of the flame front, causing pressure oscillations, metallic “ping” sound, loss of efficiency and engine damage.
- Conditions favouring knock: high compression ratio, high inlet temperature, low octane fuel, deposits/hot spots.
- Anti-knock strategies: use higher octane fuels; reduce charge temperature; adjust spark timing; engine design changes; use effective additives (modern oxygenates), and refining processes that increase octane (reforming, isomerization, alkylation).
Octane number (ON): A measure of a gasoline’s resistance to knocking in a standard SI engine test.
- Exact definition: Octane number of a fuel is the percentage by volume of iso-octane (2,2,4-trimethylpentane) in a mixture with normal heptane (n-heptane) that matches the knock intensity of the test fuel under specified conditions in a standard test engine.
- Reference fuels: n-heptane (assigned octane number 0) and iso-octane (assigned octane number 100). Mixtures of these are called primary reference fuels (PRF).
- Determination: In a standardized single-cylinder CFR (Cooperative Fuel Research) engine, adjust compression ratio to a knock standard and compare test fuel to PRF blends. Two main methods:
- Research Octane Number (RON): Measured under mild conditions (600 rpm, specified inlet temperature and humidity). Indicates part-throttle, low-speed performance.
- Motor Octane Number (MON): Measured under more severe conditions (900 rpm, higher inlet temperature, variable spark timing). Indicates high-speed, high-load performance.
- Anti-Knock Index (AKI) or Pump Octane Number (PON): The average (RON + MON)/2; commonly displayed at retail pumps in some countries. Reflects real-world mix of driving conditions.
- For fuels exceeding 100 octane by RON (due to aromatics/oxygenates), the old practice used a Performance Number (PN) scale relative to iso-octane performance; modern practice reports RON > 100 using different reference methods. In exams, if asked, state: beyond 100 RON, octane can be reported using PN or by using secondary reference fuels with toluene.
- Factors affecting octane number:
- Molecular structure: aromatics > iso-paraffins > olefins > naphthenes > normal paraffins (lowest).
- Increased branching raises octane; longer straight chains lower octane; ring formation and aromatics increase octane.
- Additives and blending: oxygenates (e.g., ethanol) generally increase octane; lead alkyls (e.g., tetraethyl lead) were highly effective but are now phased out for environmental reasons.
- Refining processes that raise octane: catalytic reforming (forms aromatics, isoparaffins), isomerization (raises C5–C6 octane), alkylation (combines isobutane with olefins to make high-octane iso-alkanes).
How to draw the CFR engine test schematic (exam diagram): Draw a single-cylinder, variable-compression engine labeled CFR. Include: carburetor/mixture control (for test fuel), intake air heater (for MON), cylinder with adjustable cylinder head (compression ratio adjustment), knock meter connected to cylinder pressure transducer, speed control (600 rpm for RON, 900 rpm for MON), exhaust. Label the comparison with PRF blends to match knock intensity.
Assumptions often required in exam derivations and numericals:
- Ideal blending of octane numbers by volume is assumed unless specified otherwise (linear additivity). Real blending shows non-linear behavior; state this limitation if asked.
- For simple cracking kinetics problems, a first-order lumped model may be assumed for conversion of a heavy fraction to lighter products.
Formulas
AKI: Anti-Knock Index (dimensionless); RON: Research Octane Number (dimensionless); MON: Motor Octane Number (dimensionless). Applies to pump labelling; arithmetic mean of standardized test results. AKI = (RON + MON)/2. Sensitivity S = RON − MON.
ON_blend = v1·ON1 + v2·ON2 + … + vn·ONn(idealized) ON_blend: octane number of blend (dimensionless); vi: volume fraction of component i (dimensionless; sum vi = 1); ONi: octane number of component i. Applies under the assumption of linear blending by volume (exam simplification).X = 1 − exp(−k·t)X: fractional conversion in a batch first-order cracking model (dimensionless); k: rate constant (s⁻¹); t: time (s). Applies when modeling a single-lump thermal or catalytic cracking step as first-order with constant k and isothermal conditions.k = A·exp(−Ea / (R·T))k: rate constant (units depend on order; s⁻¹ for first-order); A: pre-exponential factor (s⁻¹); Ea: activation energy (J·mol⁻¹); R: gas constant (8.314 J·mol⁻¹·K⁻¹); T: absolute temperature (K). Applies to Arrhenius temperature dependence if kinetics are provided.ΔT(°C) = ΔT(K)A reminder: temperature differences are numerically equal in °C and K; use absolute temperature (K) inside exponential formulas like Arrhenius.
Worked examples
- Octane number from PRF comparison (conceptual and numerical) Given: In a CFR engine under RON conditions, a test gasoline shows the same knock intensity as a blend containing 88% by volume iso-octane and 12% by volume n-heptane.
Steps:
- State definition: Octane number equals the volume percent iso-octane in the PRF blend matching knock.
- Compute ON using the PRF composition.
Calculation:
ON = 88(since iso-octane fraction is 0.88 by volume).
Answer: The RON of the test gasoline is 88.
- Blending octane numbers (ideal additivity assumption) Problem: Two gasoline streams A and B with RON values 95 and 80 are blended in the volume ratio 3:2 (A:B). Find the blend RON and the pump AKI if MON for A is 86 and for B is 74 (assume MON blends linearly by volume).
Given:
- RON_A = 95, MON_A = 86; RON_B = 80, MON_B = 74; volume fractions: v_A = 3/5 = 0.6, v_B = 0.4.
Steps:
- Use linear blending:
ON_blend = v_A·ON_A + v_B·ON_B. - Compute RON_blend and MON_blend, then AKI.
Calculations:
RON_blend = 0.6·95 + 0.4·80 = 57 + 32 = 89MON_blend = 0.6·86 + 0.4·74 = 51.6 + 29.6 = 81.2AKI = (RON_blend + MON_blend) / 2 = (89 + 81.2)/2 = 170.2/2 = 85.1
Answer: Blend RON = 89, MON = 81.2, AKI = 85.1.
- Short theory model answer: Compare thermal, catalytic and hydrocracking Write a structured answer as follows (bullet points accepted in many exams):
- Definition: Cracking is the decomposition of heavy hydrocarbons into lighter ones by breaking C–C bonds using heat and/or catalysts.
- Thermal cracking:
- Mechanism: free-radical chain reactions (initiation, β-scission, termination).
- Typical conditions: vapor-phase ≈ 600–650 °C at ≈ 0.1–0.5 MPa; liquid-phase ≈ 425–500 °C at ≈ 1–7 MPa to suppress coking.
- Products: gasoline with moderate octane, olefins (ethylene, propylene), coke, H₂.
- Pros/cons: simpler but less selective; higher coke and gum; lower gasoline octane compared to catalytic.
- Catalytic cracking (FCC):
- Mechanism: carbocations on acidic zeolites (Zeolite Y); β-scission, isomerization, hydrogen transfer; higher isoparaffin/aromatic content.
- Conditions: ≈ 450–550 °C, slight pressure ≈ 0.15–0.3 MPa; seconds of contact; catalyst continuously regenerated.
- Products: high-octane gasoline, LPG with propylene/butenes, light cycle oil.
- Pros/cons: higher gasoline yield and octane; lower coke than thermal; needs catalyst/regenerator.
- Hydrocracking:
- Mechanism: bifunctional—acid cracking plus metal-catalyzed hydrogenation; saturates aromatics, removes sulfur/nitrogen.
- Conditions: ≈ 350–450 °C; high H₂ pressure ≈ 7–20 MPa.
- Products: low-sulfur middle distillates or high-octane naphtha; very clean fuels.
- Pros/cons: flexible and clean but high capital and hydrogen demand.
- Conclusion: Choose process based on feed quality and desired product slate; catalytic and hydrocracking dominate modern refineries for fuel quality and emissions.
Common mistakes
- Assuming blending octane is always linear. In reality, blending is non-ideal (e.g., ethanol shows octane synergy). State the assumption when you use linear additivity in numericals.
- Mixing up RON and MON test conditions or their interpretation; RON is milder (600 rpm) and higher than MON for the same fuel; “sensitivity” = RON − MON.
- Giving non-SI units without conversion. Use K for absolute T and Pa/MPa for pressure. If quoting °C in industrial ranges, include the equivalent K in parentheses when needed.
- Drawing incomplete diagrams: forgetting to show FCC catalyst regenerator, cyclones, or the reflux in a distillation column.
- Stating that lead additives are still used in automotive gasoline. They are largely phased out globally due to toxicity; aviation gasoline is a separate case.
For your exam
Expect a mix of:
- Definitions: fuel, liquid fuel, flash point, fire point, pour point, aniline point, knocking, octane number, RON, MON, AKI.
- Short notes: thermal vs catalytic cracking; FCC unit operation and catalyst; hydrocracking advantages; factors affecting octane number; role of oxygenates (ethanol) and environmental aspects of lead.
- Diagrams: fractional distillation column; FCC reactor–regenerator with main fractionator; CFR engine setup for octane measurement. Draw cleanly, label streams/components and operating conditions.
- Derivations/structured answers: carbocation vs free-radical mechanisms (schematic), effect of molecular structure on octane with examples (n-heptane vs iso-octane, toluene).
- Numericals: octane number by PRF comparison; blend octane by linear additivity; compute AKI and sensitivity from given RON/MON; simple first-order cracking conversion problems.
- What full-marks answers include: precise definitions with units; clearly stated assumptions; neat, well-labeled diagrams; steps with formulas before numbers; final answers emphasized; limitations acknowledged (e.g., non-ideal blending).
Quick check
- Define octane number and name the two primary reference fuels with their assigned numbers.
- List two differences between thermal cracking and catalytic cracking.
- A gasoline has RON 92 and MON 84. Find its AKI and sensitivity.
Answers: 1) Octane number is the volume percent of iso-octane in a mixture with n-heptane that shows the same knock intensity as the test fuel in a standard engine; reference fuels are n-heptane (0) and iso-octane (100). 2) Thermal: free-radical, higher T and (often) lower selectivity, more olefins/coke; Catalytic: carbocation on acidic zeolites at lower T, higher gasoline yield and octane with continuous catalyst regeneration (FCC). 3) AKI = (92 + 84)/2 = 88; sensitivity = RON − MON = 8.
Finished this topic? Mark it so your progress, study plan and readiness keep up.
Stuck on something here?