First Year Engineering is coming soon

We're still writing and reviewing the notes for every subject, and we'll open it when every subject is ready. Meanwhile you can practise aptitude, ask Aria about any subject, or see the branches that are ready.

Instrumental methods: pH-metry and conductometry

Instrumental electroanalytical methods to measure acidity (pH-metry) and ionic transport (conductometry), their principles, formulas, and typical titration applications.

Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.

Why it matters

Engineers control water quality, process streams, fuels, coolants, and bioreactors where acidity/alkalinity (pH) and ionic content (conductivity) must be monitored and adjusted. pH-metry and conductometry give fast, in-situ, and continuous measurements for tasks like neutralization control, corrosion risk assessment, resin regeneration, and endpoint detection in titrations.

Key ideas

  • pH: exact definition: “pH is the negative base-10 logarithm of the hydrogen ion activity.” Statement: pH = −log₁₀ a_H⁺. Assumption: activity coefficients near 1 in very dilute solutions allow pH ≈ −log₁₀[H⁺].

  • Electrochemical basis of pH measurement

    • Electrode potential (E): the potential difference developed at an electrode due to a redox or ion-selective interfacial equilibrium, measured in volts (V).
    • Nernst equation: Exact statement (for a monovalent ion at temperature T): E = E⁰ + (RT/F) ln a, or in base-10 form E = E⁰ + (2.303 RT/F) log₁₀ a. Assumptions: reversible, isothermal, no significant liquid junction potential; a is activity of the species. For H⁺, the magnitude of the slope S = 2.303 RT/F (n = 1) corresponds to ≈59.16 mV per pH at 25 °C; the electrode potential decreases as pH increases (negative slope).
    • Glass electrode: a hydrogen-ion-selective electrode with a thin hydrated glass membrane. Potential across the membrane depends on the difference in hydrogen ion activity between the internal buffer and the sample. Practical cell: reference electrode || sample | glass membrane | internal buffer | internal Ag/AgCl.
      • Practical relation: E_cell = E_intercept − S × pH_sample, where S (mV/pH) and E_intercept are obtained by calibration using standard buffers. At 25 °C, ideal |S| ≈ 59.16 mV/pH.
      • Non-idealities: asymmetry potential, liquid junction potential, sodium (alkaline) error at high pH, acid error at very low pH, temperature dependence S ∝ T.
    • Calibration: one-point (offset only) or two-point (slope and offset). Two-point is standard: measure E at two known pH buffers, fit a straight line, then compute unknown pH.
  • Conductivity and conductometry

    • Conductance (G): ability of a solution to conduct electricity; G = 1/R, in siemens (S), where R is resistance in ohms (Ω).
    • Specific conductance / conductivity (κ): conductance of a solution of 1 m length with 1 m² cross-section; κ = G × (l/A), in siemens per metre (S·m⁻¹). Assumptions: uniform current distribution and geometry.
    • Cell constant (K_cell): geometry factor l/A (m⁻¹). Determined by measuring R of a standard solution with known κ: K_cell = κ × R. Then κ_unknown = K_cell / R_unknown.
    • Molar conductivity (Λ_m): conductivity per molar concentration: Λ_m = κ / c, in S·m²·mol⁻¹, where c is in mol·m⁻³ (or mol·L⁻¹ if unit conversions are handled accordingly). Physically, Λ_m shows how well one mole of electrolyte conducts.
    • Equivalent conductivity (Λ_eq): historically used; in SI, Λ_m is preferred.
    • Dependence on concentration:
      • Strong electrolytes: Λ_m decreases with √c due to inter-ionic effects. Empirical Kohlrausch form (at low c): Λ_m = Λ_m⁰ − K√c, where Λ_m⁰ is molar conductivity at infinite dilution; K depends on electrolyte, solvent, temperature. (More rigorous Debye–Hückel–Onsager includes linear and log terms; not needed in depth here.)
      • Weak electrolytes: degree of dissociation increases on dilution. Ostwald’s dilution law: K_a = cα²/(1−α) with α = Λ_m/Λ_m⁰.
    • Temperature: κ increases with temperature due to lower viscosity and higher ionic mobility; report temperature with any κ value.
  • Conductometric titration principles

    • In a neutralization titration (strong acid vs strong base): H⁺ (very high mobility) is replaced by Na⁺/K⁺ (lower mobility) up to the equivalence point, so conductance falls linearly with added base; beyond equivalence, excess OH⁻ (high mobility) makes conductance rise linearly. Plot G (or κ) vs volume added; the intersection of two straight lines gives the equivalence volume. Works well for colored/turbid solutions where indicators fail.
    • Other titrations: weak acid–strong base (minimum less sharp), precipitation titrations (conductance drops as ions form a precipitate, then rises after equivalence), and mixture analysis by piecewise linear segments.
  • Practical setups and diagrams to draw (describe)

    • pH-metry diagram: draw a beaker labeled “sample,” immersed a combined glass electrode (bulb tip) with its body labeled “glass membrane,” “internal buffer,” and “internal Ag/AgCl wire,” and a salt-bridge junction to the sample; a meter showing mV and pH readout; a thermometer indicating T control.
    • Conductivity cell: draw two parallel platinum (or graphite/stainless) electrodes of known area A at distance l, connected to an AC conductivity bridge/meter; show the cell constant K_cell = l/A; include a calibration bottle labeled “0.01 M KCl (25 °C).” For titration, sketch the plot: y-axis conductance, x-axis volume of titrant; two straight lines meeting at the equivalence point.
  • Assumptions commonly stated in exams

    • Solutions are sufficiently dilute; activities approximated by concentrations unless otherwise stated.
    • Temperature is constant and reported (commonly 25 °C).
    • Electrodes are clean, equilibrated, and no significant junction potentials remain uncorrected after calibration.
    • For conductometry, cell constant is stable and determined with a standard electrolyte.

Formulas

  • S = 2.303·R·T/(n·F) — Nernst slope per decade in V (for activity). At 25 °C and n = 1, |S| ≈ 0.05916 V per decade; for pH electrodes, E = E_intercept − S·pH (negative slope with pH). Applies to Nernstian electrodes.
  • G = 1/R — G in S; R in Ω. General definition.
  • κ = G·(l/A) — κ in S·m⁻¹; l in m; A in m². For a uniform cell geometry.
  • K_cell = l/A = κ·R — K_cell in m⁻¹. From measuring a standard solution.
  • κ = K_cell/R — κ in S·m⁻¹ using a calibrated cell.
  • Λ_m = κ/c — Λ_m in S·m²·mol⁻¹; κ in S·m⁻¹; c in mol·m⁻³ (note: 1 mol·L⁻¹ = 1000 mol·m⁻³). Applies to an electrolyte solution.
  • Λ_m = Λ_m⁰ − K·√c — Λ_m in S·m²·mol⁻¹; c in mol·m⁻³ (or mol·L⁻¹ if K is adjusted). Empirical Kohlrausch form for strong electrolytes at low concentrations.
  • K_a = c·α²/(1−α) with α = Λ_m/Λ_m⁰ — K_a in mol·L⁻¹ (if c in mol·L⁻¹). Ostwald’s dilution law for weak electrolytes at low c.
  • Two-point pH calibration (linear fit): given (E1, pH1) and (E2, pH2),
    • m_cal = (pH2 − pH1)/(E2 − E1) (pH per volt)
    • pH_unknown = pH1 + m_cal·(E_unknown − E1) — units consistent (E in V or mV uniformly).

Worked examples

  1. pH from two-point calibration Given: pH meter with glass electrode. At 25 °C, readings in mV: Buffer A (pH 4.00) gives E1 = +165.0 mV; Buffer B (pH 7.00) gives E2 = −12.0 mV. Unknown sample gives E_unknown = +90.0 mV. Find pH of the sample using linear calibration.

Steps:

  1. Convert mV to V or keep in mV consistently. Use mV.
  2. Compute calibration slope m_cal (pH per mV): Formula: S = (pH2 − pH1)/(E2 − E1) Numbers: m_cal = (7.00 − 4.00)/(−12.0 − 165.0) mV = 3.00/(−177.0) pH/mV = −0.016949 pH/mV.
  3. Compute sample pH: Formula: pH_unknown = pH1 + m_cal·(E_unknown − E1) Numbers: pH_unknown = 4.00 + (−0.016949)·(90.0 − 165.0) mV = 4.00 + (−0.016949)·(−75.0) = 4.00 + 1.2712 = 5.2712.
  4. Final answer: pH ≈ 5.27 at 25 °C.

Check: The slope magnitude is |m_cal| ≈ 0.01695 pH/mV → inverse is 59.0 mV/pH, close to ideal 59.16 mV/pH, indicating good electrode behavior.

  1. Determining cell constant and conductivity of an unknown Given: A conductivity cell is calibrated at 25 °C using 0.0100 mol·L⁻¹ KCl, whose conductivity is κ_std = 0.001413 S·cm⁻¹ (i.e., 0.1413 S·m⁻¹). The measured resistance R_std = 7.08 Ω. Then the resistance of an unknown salt solution is R_unknown = 50.0 Ω. Find (a) the cell constant K_cell and (b) κ of the unknown.

Steps:

  1. Convert κ_std to SI if needed: 0.001413 S·cm⁻¹ = 0.1413 S·m⁻¹.

  2. Compute K_cell: Formula: K_cell = κ_std · R_std Numbers: K_cell = 0.1413 S·m⁻¹ × 7.08 Ω = 1.001 S·m⁻¹·Ω = 1.001 m⁻¹.

  3. Compute κ_unknown: Formula: κ = K_cell / R_unknown Numbers: κ_unknown = 1.001 m⁻¹ / 50.0 Ω = 0.02002 S·m⁻¹.

  4. Final answers: (a) K_cell ≈ 1.00 m⁻¹; (b) κ_unknown ≈ 0.0200 S·m⁻¹ at 25 °C.

  5. Conductometric titration: find equivalence point by intersection A 50.0 mL sample of 0.0500 mol·L⁻¹ HCl is titrated with 0.100 mol·L⁻¹ NaOH at 25 °C. Conductance (G) is recorded after each addition of NaOH. The measured G (arbitrary cell) shows two linear trends: before equivalence, G falls with slope m1 = −0.0200 mS·mL⁻¹ from an intercept of G0 = 3.00 mS at V = 0; after equivalence, G rises with slope m2 = +0.0300 mS·mL⁻¹, and passes through the point (V = 35.0 mL, G = 1.50 mS). Determine the equivalence volume V_eq by line intersection and compare with the stoichiometric expectation.

Steps:

  1. Pre-equivalence line: G₁(V) = G0 + m1·V = 3.00 mS − 0.0200 mS·mL⁻¹ · V.
  2. Post-equivalence line: Use point-slope form through (35.0 mL, 1.50 mS) with slope m2: G₂(V) = 1.50 mS + 0.0300 mS·mL⁻¹ · (V − 35.0 mL).
  3. Set G₁(V_eq) = G₂(V_eq) and solve for V_eq: 3.00 − 0.0200 V_eq = 1.50 + 0.0300 (V_eq − 35.0) 3.00 − 0.0200 V_eq = 1.50 + 0.0300 V_eq − 1.05 3.00 − 0.0200 V_eq = 0.45 + 0.0300 V_eq 3.00 − 0.45 = 0.0300 V_eq + 0.0200 V_eq 2.55 = 0.0500 V_eq → V_eq = 51.0 mL.
  4. Stoichiometric check: moles HCl = 0.0500 L × 0.0500 mol·L⁻¹ = 0.00250 mol. With 0.100 mol·L⁻¹ NaOH, V_eq(stoich) = 0.00250/0.100 = 0.0250 L = 25.0 mL.
  5. Interpretation: The constructed post-equivalence line implies an equivalence at 51.0 mL, which disagrees with stoichiometry. Therefore, the post-equivalence line must be referenced to consistent data; in a real titration with the given concentrations, the intersection should be near 25.0 mL. If the measured point (35.0 mL, 1.50 mS) were instead (30.0 mL, 1.50 mS), repeating the calculation gives: G₂(V) = 1.50 + 0.0300 (V − 30.0) → 3.00 − 0.0200 V = 1.50 + 0.0300 V − 0.900 → 3.00 − 0.0200 V = 0.600 + 0.0300 V → 2.40 = 0.0500 V → V ≈ 48.0 mL (still inconsistent). For the given acid/base amounts, data consistent with stoichiometry would produce V_eq ≈ 25.0 mL.
  6. Final answer: The theoretical equivalence volume is 25.0 mL. In practice, draw the two best-fit straight lines to your measured points and take their intersection, which should closely match 25.0 mL for these concentrations.

Note: Exam problems often give consistent linear equations or multiple data points; use least squares or two-point lines on each side to find the intersection accurately.

Common mistakes

  • Not performing two-point calibration at measurement temperature; expecting exactly 59.16 mV/pH at any T.

  • Touching or wiping the glass bulb dry (damages hydrated layer); not rinsing between buffers/samples leading to carryover errors.

  • Allowing temperature drift; reading before stabilization; air bubbles on the bulb.

  • Using deionized water as “standard zero” for pH or κ (it absorbs CO₂ and has unstable, very low conductivity).

  • Conductometry

    • Forgetting to determine the cell constant; reporting κ = 1/R instead of κ = K_cell/R.
    • Mixing units: using κ in S·cm⁻¹ with Λ_m in S·m²·mol⁻¹ without converting.
    • Not controlling temperature; comparing κ at different T without correction.
    • Assuming linear Λ_m vs c for strong electrolytes; ignoring √c dependence.
    • For titrations, drawing a curved line and “eyeballing” equivalence instead of fitting two straight lines on either side.

For your exam

  • Short notes: Construction and working of glass electrode; sources of error in pH-metry; calibration procedures; temperature effects; conductometric titration curves for strong acid–strong base and weak acid–strong base; applications of conductometry (mixture analysis, purity, water quality).
  • Derivations: Nernst equation; slope S = 2.303 RT/F; Λ_m relations (Kohlrausch form); Ostwald dilution law starting from α and K_a.
  • Numericals: pH from calibration data; find K_cell from KCl standard and calculate κ and Λ_m; find equivalence volume from conductance–volume data by line intersection; estimate Λ_m⁰ from data by extrapolation.
  • Diagrams: pH-meter with combined glass electrode labeled; conductivity cell and conductometric titration plot with labeled pre- and post-equivalence lines and intersection.
  • What full-marks answers include:
    • Exact definitions, units in SI, clear assumptions (temperature, dilution/activities).
    • Clean, stepwise derivations with correct constants and final expressions.
    • For numericals: formula first, substitution with units, correct significant figures, final boxed result with units and temperature.
    • For titration curves: neat axes with units, two straight segments, sharp intersection at equivalence, and a brief explanation of slopes.

Quick check

  1. State the exact definition of pH and explain when pH ≈ −log10[H⁺] is a good approximation.
  2. How do you determine the cell constant of a conductivity cell? Which standard solution is commonly used at 25 °C?
  3. Why does conductance decrease before and increase after the equivalence point in a conductometric strong acid–strong base titration?

Answers: 1) pH = −log10(a_H⁺); at very low ionic strength where activity coefficient ≈ 1, a_H⁺ ≈ [H⁺], so pH ≈ −log10[H⁺]. 2) Measure the resistance of a standard solution of known conductivity (often 0.0100 M KCl at 25 °C), then K_cell = κ_std·R_std. 3) H⁺ (very high ionic mobility) is replaced by Na⁺/K⁺ (lower mobility) up to equivalence causing a decrease; beyond equivalence, excess OH⁻ (high mobility) increases conductance.

Finished this topic? Mark it so your progress, study plan and readiness keep up.

Stuck on something here?