Boiler troubles
Boiler troubles: scale and sludge formation, priming and foaming, carryover, boiler corrosion, and caustic embrittlement, with causes, chemistry, prevention, and treatments.
Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.
Why it matters
Boilers produce steam for power, heating, and process work. Deposits, corrosion, and steam-quality problems reduce efficiency, waste fuel, cause tube failures, and even lead to dangerous accidents. Understanding boiler troubles and their control is essential for safe, economic plant operation and for exams.
Key ideas
- Scale: A hard, adherent, crystalline deposit on boiler heat-transfer surfaces, mainly from salts whose solubility decreases or which decompose on heating (e.g., CaCO₃, CaSO₄, silicates). Scale resists heat flow and causes overheating.
- Sludge: A soft, loose, non-adherent precipitate that deposits in low-flow areas (mud drum). It usually forms from salts that precipitate as fine particles during heating and can be removed by blowdown.
- Priming: Carryover of liquid water droplets with steam due to violent boiling, high water level, or sudden load changes.
- Foaming: Stable foam on boiler water surface caused by oils, soaps, alkalis, or high TDS; leads to wet steam and carryover.
- Carryover: Entrainment of dissolved and suspended solids into steam due to priming/foaming; causes deposits in superheaters/turbines and corrosion in condensate lines.
- Boiler corrosion: Electrochemical attack of boiler metal by dissolved oxygen, carbon dioxide, acids, or under-deposit conditions, leading to pitting, wastage, and failures.
- Caustic embrittlement: Intergranular cracking of boiler steel at high-stress points due to concentration of NaOH and formation of alkaline corrosion products; aggravated by sodium carbonate/caustic treatment and leaks.
- Internal conditioning: Chemicals (phosphate, carbonate, calgon, dispersants, antifoams, oxygen scavengers) dosed into boiler/boiler feed to prevent scale, sludge deposition, foaming, and corrosion.
- External treatment: Pretreatment processes outside the boiler (softening, demineralization, deaeration) to remove hardness and gases before feeding to the boiler. For details, see other topics (Hardness; Water softening; Desalination).
Exact definitions for exams:
- Definition (Scale): “Scale is a hard, adherent deposit on boiler heat-transfer surfaces, formed by the precipitation or decomposition of dissolved salts (such as CaCO₃, CaSO₄, and silicates) under boiler conditions.”
- Definition (Sludge): “Sludge is a soft, loose, non-adherent precipitate formed within the boiler water, typically settling in areas of low flow.”
- Definition (Priming): “Priming is the mechanical carryover of liquid water droplets with steam from the boiler, usually due to high water level, sudden boiling, or impurities.”
- Definition (Foaming): “Foaming is the formation of persistent bubbles or foam on the boiler water surface, caused by the presence of oils, fatty acids, alkalis, or high dissolved solids.”
- Definition (Carryover): “Carryover is the transport of dissolved and suspended solids from boiler water into the steam due to priming and foaming.”
- Definition (Caustic embrittlement): “Caustic embrittlement is intergranular cracking of boiler steel under stress, caused by the concentration of caustic alkali (NaOH) at crevices and riveted joints.”
Why scale forms (thermodynamics and reactions):
- Decrease of solubility with temperature: e.g., CaSO₄ becomes less soluble as temperature increases; thus it precipitates as a hard scale at high-temperature surfaces.
- Thermal decomposition of bicarbonates: Temporary hardness salts decompose on heating:
- Ca(HCO₃)₂ → CaCO₃↓ + CO₂↑ + H₂O
- Mg(HCO₃)₂ → Mg(OH)₂↓ + 2CO₂↑
- Silica can form hard silicate scales (e.g., CaSiO₃) or deposit with magnesium as MgSiO₃.
Why sludge forms (hydrodynamics and precipitation):
- Fine precipitates form in bulk water and remain suspended or settle in low-flow zones (mud drum). They are soft and removable by blowdown.
Disadvantages:
- Scale: lower heat-transfer coefficient, higher fuel consumption, tube overheating and failure, reduced steam output, under-deposit corrosion.
- Sludge: chokes flow, reduces circulation, causes localized overheating and corrosion; but easier to remove than scale.
Internal conditioning chemistry:
- Phosphate conditioning (preferred): Convert hardness to soft, non-adherent sludges at controlled pH.
- 3Ca²⁺ + 2PO₄³⁻ → Ca₃(PO₄)₂↓
- Mg²⁺ + 2OH⁻ → Mg(OH)₂↓ (OH⁻ from phosphate hydrolysis)
- Sodium phosphates used: Na₃PO₄ (trisodium phosphate), Na₂HPO₄ (disodium), NaH₂PO₄ (mono) to buffer pH.
- Carbonate treatment (low-pressure only; control carefully):
- Ca²⁺ + CO₃²⁻ → CaCO₃↓
- Mg²⁺ + 2OH⁻ → Mg(OH)₂↓ (OH⁻ from carbonate hydrolysis)
- Calgon (sodium hexametaphosphate) sequestration: complexes Ca²⁺/Mg²⁺ to keep them soluble and non-scaling.
- Dispersants/conditioners (tannin, lignin, polymers): keep precipitates dispersed as sludge.
- Antifoams (silicones, poly-glycols): suppress foam.
- Oxygen scavengers: Na₂SO₃ + 1/2 O₂ → Na₂SO₄; N₂H₄ + O₂ → N₂ + 2H₂O.
External treatments supporting boilers:
- Softening (zeolite, ion exchange) to remove Ca²⁺/Mg²⁺.
- Demineralization to remove all ions when high-purity water is required.
- Deaeration (mechanical + chemical) to remove O₂ and CO₂.
Boiler corrosion mechanisms:
- Oxygen corrosion (pitting): 2Fe + O₂ + 2H₂O → 2Fe(OH)₂; further to Fe₂O₃·H₂O (rust). Prevent by deaeration and scavengers (sulfite, hydrazine).
- Carbon dioxide corrosion (carbonic acid in condensate): CO₂ + H₂O → H₂CO₃; Fe + 2H₂CO₃ → Fe(HCO₃)₂ + H₂↑. Prevent by removing CO₂ and maintaining alkalinity/neutralizing amines (plant-specific).
- Acid corrosion from MgCl₂ hydrolysis: MgCl₂ + 2H₂O → Mg(OH)₂ + 2HCl; HCl causes rapid metal loss unless neutralized by alkalinity.
- Under-deposit corrosion: Differential aeration cells under scale/sludge create anodic spots and pitting.
Caustic embrittlement mechanism and prevention:
- At crevices and leaks, water evaporates and concentrates NaOH. High-pH solution attacks iron along grain boundaries; protective magnetite film may be altered to soluble alkaline iron compounds (e.g., sodium ferrites), leading to intergranular cracking under stress.
- Prevention: Avoid excessive caustic/alkalinity, prefer coordinated phosphate treatment, eliminate leaks/crevices, use balanced sodium phosphate blends (phosphate-pH control), add inhibitors (e.g., sodium nitrate) where specified, and control boiler water pH within recommended range for the pressure class.
Priming, foaming, carryover — causes and control:
- Causes: High water level, sudden load increase, high TDS/suspended solids, foaming due to oil/alkali/organic matter, improper drum internals.
- Effects: Wet steam, deposits in superheaters/turbines, water hammer, erosion-corrosion.
- Control: Maintain proper drum level and firing, limit boiler-water TDS via blowdown, use antifoams, remove oil (degrease feedwater), use steam separators and demisters, ensure good drum internals.
Cleaning and removal of deposits:
- Sludge: removed by periodic and continuous blowdown.
- Scale: mechanical cleaning (scraping, brushing), chemical cleaning (inhibited 5–10% HCl or sulfamic acid), chelant cleaning (EDTA). Rinse and passivate after cleaning.
Typical diagram to draw and label (exam):
- “Boiler drum with deposits and steam separation”: Draw a horizontal drum. Mark: water level, bottom blowdown, riser tubes entering drum, scale on tubes (hard, adherent), sludge at bottom (soft layer), steam space with demister/separator, steam outlet, continuous blowdown line, chemical dosing point.
- “Electrochemical cell for oxygen corrosion under a deposit”: Sketch metal surface with a scale patch; label anodic area under deposit, cathodic area outside, oxygen gradient, electron flow in metal, ion flow in water, rust formation zone.
Formulas
- Thermal decomposition of calcium bicarbonate causing CaCO₃ scale. Applies in boilers heated above about 60–80 °C.
Mg(HCO3)2 → Mg(OH)2↓ + 2CO2↑- Thermal decomposition of magnesium bicarbonate, giving Mg(OH)₂ sludge/scale.
Ca2+ + CO3(2−) → CaCO3↓- Carbonate conditioning/precipitation reaction; CaCO₃ tends to form scale if not dispersed.
3Ca2+ + 2PO4(3−) → Ca3(PO4)2↓- Phosphate conditioning; forms a soft sludge if well-dispersed.
Na2SO3 + 1/2 O2 → Na2SO4- Oxygen scavenging by sodium sulfite; typical for low/medium pressure boilers.
N2H4 + O2 → N2 + 2H2O- Oxygen scavenging by hydrazine; gives no dissolved solids.
MgCl2 + 2H2O → Mg(OH)2 + 2HCl- Hydrolysis generating acid; leads to corrosion unless alkalinity neutralizes it.
- Definitions for cycles of concentration (C) and blowdown (B) at steady state:
C = (TDS in boiler water) / (TDS in makeup water)- Dimensionless; indicates concentration factor.
B / M = 1 / C- B = blowdown mass flow (kg/s), M = makeup water flow (kg/s). Applies when steam carries no TDS and system is at steady state.
B / S = 1 / (C − 1)- S = steam mass flow (kg/s); derived using M = S + B at steady state.
% blowdown of makeup = 100 / C- Percentage basis with respect to makeup flow.
Worked examples
- Theory: Distinguish scale and sludge; give causes, ill effects, and prevention. Model answer outline:
- Scale vs sludge: Scale is hard, adherent, crystalline; sludge is soft, non-adherent. Scale arises from decreased solubility (CaSO₄) and thermal decomposition (Ca(HCO₃)₂ → CaCO₃), plus silica. Sludge arises from fine precipitates (e.g., Mg(OH)₂, Ca₃(PO₄)₂) forming in bulk water and settling in low-flow zones.
- Ill effects: Scale reduces heat transfer, causes tube overheating and failure; sludge blocks circulation, causes under-deposit corrosion. Both lower efficiency and require shutdown for cleaning.
- Prevention: External softening/demineralization; internal phosphate conditioning with proper pH, dispersants; continuous/periodic blowdown to control TDS; oil removal to avoid foaming; regular monitoring of hardness, phosphate, pH, and TDS.
- Numerical: Calculate required blowdown rate. Given: Steam production S = 10.0 kg/s; TDS in makeup = 500 mg/L (≈ 500 ppm by mass ≈ 0.0005 kg/kg); allowable TDS in boiler water = 3500 mg/L; steady state. Steps:
- Compute cycles of concentration: C = TDS_boiler / TDS_makeup = 3500 / 500 = 7.0 (dimensionless).
- Use
B / S = 1 / (C − 1)with C = 7.0: B/S = 1 / (7.0 − 1) = 1/6 = 0.1667. - Compute blowdown mass flow: B = 0.1667 × S = 0.1667 × 10.0 kg/s = 1.667 kg/s.
- Compute makeup: M = S + B = 10.0 + 1.667 = 11.667 kg/s. Check: B/M = 1/C = 1/7 ≈ 0.1429 (consistent: 1.667/11.667 = 0.1429). Answer: Blowdown rate = 1.667 kg/s.
- Theory with reactions: Explain oxygen and carbon dioxide corrosion in boilers and their prevention. Model answer:
- Oxygen corrosion: Dissolved O₂ causes pitting: 2Fe + O₂ + 2H₂O → 2Fe(OH)₂ → rust (Fe₂O₃·H₂O). Prevention: mechanical deaeration (deaerator to <10–20 µg/L O₂), chemical scavengers (Na₂SO₃ → Na₂SO₄; N₂H₄ → N₂ + 2H₂O), maintain alkaline pH to stabilize magnetite film (Fe₃O₄), avoid stagnant zones.
- CO₂ corrosion: CO₂ forms carbonic acid: CO₂ + H₂O → H₂CO₃; in condensate lines, Fe + 2H₂CO₃ → Fe(HCO₃)₂ + H₂↑, thinning pipes. Prevention: remove CO₂ by proper external treatment and degassing; limit carbonate treatment to reduce CO₂ evolution; maintain condensate alkalinity/neutralizing amines as per plant practice; use deaeration and return-line monitoring.
Common mistakes
- Forgetting that blowdown must be calculated from TDS balance and cycles of concentration; using a wrong direct percent.
- Overdosing sodium carbonate for internal treatment, which can cause caustic embrittlement and CO₂ release that corrodes condensate lines.
- Ignoring dissolved oxygen — even a few µg/L can cause severe pitting.
- Drawing unlabeled diagrams; exam diagrams need clear labels (scale vs sludge positions, separators, blowdown lines).
For your exam
Quick check
- Write two chemical reactions that explain formation of scale from temporary hardness.
- State two causes and two remedies for foaming in boilers.
- A boiler operates at C = 6 cycles of concentration. What is the ratio B/S? Answers: 1) Ca(HCO₃)₂ → CaCO₃↓ + CO₂ + H₂O; Mg(HCO₃)₂ → Mg(OH)₂↓ + 2CO₂. 2) Causes: oil/alkali contamination, high TDS; Remedies: remove oil/organics, dose antifoam, control TDS via blowdown, improve drum internals. 3) B/S = 1/(C − 1) = 1/5 = 0.2.
Finished this topic? Mark it so your progress, study plan and readiness keep up.
Stuck on something here?