Stress, strain and elastic constants
Builds the foundations of stress, strain, and elastic constants (E, G, K, ν), their relationships, and linear elastic constitutive laws in 1D and 3D, with sign conventions and standard results.
Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.
Why it matters
Understanding stress–strain relationships lets you size parts, predict deformations, and avoid failure. From bolts in tension to shafts in torsion and pressure vessels, every later topic uses these constants and laws. Clear command here saves time across design, analysis, and GATE ME problems.
Key ideas
- Stress (σ, τ): Internal force per unit area developed within a body to resist external loads. Normal stress (σ) acts perpendicular to the area; shear stress (τ) acts tangentially. Unit: Pa (N/m²).
- Sign conventions (this note’s convention): Tension is positive (+σ), compression negative (−σ). Engineering shear stress τ_xy is positive if it acts in the positive y-direction on the face whose outward normal is +x; the corresponding shear strain γ_xy is positive for the same sense of distortion.
- Axial/normal loading: Load parallel to the member’s axis produces normal stress, σ = P/A, when the load is centric and the section is uniform.
- Shear loading: Tangential load on an area produces shear stress τ = V/A (average on a plane). Complementary shear stresses appear on perpendicular planes; their magnitudes are equal and directions form a couple to satisfy moment equilibrium.
- Strain: Deformation measure.
- Normal strain (ε) = change in length/original length. Dimensionless.
- Shear strain (γ) = change in right angle between two initially perpendicular line elements; in radians (dimensionless).
- Small strain assumption: Deformations are small compared to dimensions so geometry changes do not significantly alter force directions or areas; strains add linearly.
- Elastic behavior: Material returns to original dimensions upon unloading (within elastic range). The linear portion follows laws below.
- Hooke’s law (1D): Within the proportional limit, normal stress is proportional to normal strain: σ = E·ε.
- Modulus of Elasticity (Young’s modulus, E): Ratio of normal stress to normal strain in uniaxial linear elastic response. Unit: Pa.
- Poisson’s ratio (ν): Negative ratio of lateral strain to longitudinal strain in uniaxial loading: ν = −(ε_lateral / ε_longitudinal). Dimensionless. Typical metals ~0.25–0.35; rubber-like solids approach 0.5.
- Shear modulus (modulus of rigidity, G): Ratio of shear stress to engineering shear strain in linear elastic response: τ = G·γ. Unit: Pa.
- Bulk modulus (K): Ratio of hydrostatic pressure to volumetric strain: K = −p / (ΔV/V). Unit: Pa. Larger K means lower compressibility.
- Volumetric strain (ε_v): Sum of normal strains in three orthogonal directions: ε_v = ε_x + ε_y + ε_z.
- Isotropic, homogeneous, linear elasticity (3D generalized Hooke’s law): For small strains and isotropy, the normal strain along an axis depends on all normal stresses:
- ε_x = (1/E)[σ_x − ν(σ_y + σ_z)], and cyclic permutations for ε_y, ε_z.
- Engineering shear strains: γ_xy = τ_xy / G, γ_yz = τ_yz / G, γ_zx = τ_zx / G.
- Interrelations of elastic constants (isotropic solids): Only two independent constants are needed. Standard identities:
- E = 2G(1 + ν)
- E = 3K(1 − 2ν)
- E = 9KG / (3K + G)
- ν = (3K − 2G) / [2(3K + G)]
- Plane stress vs. plane strain:
- Plane stress: σ_z ≈ 0 (thin plates under in-plane loads). Out-of-plane strain exists: ε_z = −(ν/E)(σ_x + σ_y).
- Plane strain: ε_z ≈ 0 (long bodies with uniform cross-section where out-of-plane strain is constrained). Then σ_z is generally non-zero; from Hooke’s law with ε_z = 0: σ_z = ν(σ_x + σ_y).
- Hydrostatic stress and volumetric strain: For σ_x = σ_y = σ_z = −p (compression positive as pressure), ε_v = (1/E)[(1 − 2ν)(σ_x + σ_y + σ_z)] = −3p(1 − 2ν)/E, hence K = E/[3(1 − 2ν)].
- Uniaxial loading (standard result): If σ_x = σ, σ_y = σ_z = 0, then ε_x = σ/E, ε_y = ε_z = −νσ/E. Volumetric strain ε_v = (1 − 2ν)σ/E.
- Pure shear (standard result): Under τ_xy = τ (other stresses zero), normal strains are zero (ε_x = ε_y = ε_z = 0); only shear strain occurs with γ_xy = τ/G. The principal stresses under pure shear are ±τ (directions at 45° to shear planes); covered in detail under Principal Stresses and Mohr’s Circle.
- Ranges and realism:
- Thermodynamic stability for an isotropic linear elastic solid requires −1 < ν < 0.5 and E > 0, G > 0, K > 0. Most engineering solids have 0 ≤ ν ≤ 0.5.
- Real materials show plasticity, creep, damage, anisotropy, temperature dependence; linear elastic, isotropic models approximate initial, small-strain behavior.
- Superposition: Within the linear elastic range, total strain equals the algebraic sum from individual stress components (compatibility and boundary conditions must be satisfied).
- Assumptions stated unless noted: small strains, linear elasticity, homogeneous, isotropic, loads applied gradually, stress uniform away from load application regions (Saint-Venant’s principle).
Formulas
σ = P / A — Normal stress; P: axial load (N), A: cross-sectional area (m²), σ: normal stress (Pa). Uniform, centric axial loading.
τ = V / A — Average shear stress; V: shear force (N), A: resisting area (m²), τ: shear stress (Pa). Uniform shear distribution assumption.
ε = ΔL / L — Normal strain; ΔL: change in length (m), L: original length (m), ε: strain (dimensionless). Small strain.
γ = Δθ — Engineering shear strain equals change in right angle; γ: shear strain (rad), Δθ: angular distortion (rad). Small angles (radians).
ε_xy = γ_xy / 2 — Relation between tensorial shear strain component ε_xy and engineering shear strain γ_xy; dimensionless.
σ = E·ε — Hooke’s law in 1D; σ: stress (Pa), ε: strain, E: Young’s modulus (Pa). Within proportional limit.
τ = G·γ — Linear shear response; τ: shear stress (Pa), γ: shear strain (rad), G: shear modulus (Pa). Within linear range.
ν = - ε_lateral / ε_longitudinal — Poisson’s ratio; dimensionless. Uniaxial stress in isotropic linear elastic material.
ε_v = ε_x + ε_y + ε_z — Volumetric strain; dimensionless. Small strain.
ε_x = (1/E)[σ_x − ν(σ_y + σ_z)] — 3D Hooke’s law; σ_i: normal stresses (Pa), ε_i: normal strains, E: Pa, ν: dimensionless. Isotropic, linear elastic.
γ_xy = τ_xy / G — Shear relation; τ_xy: shear stress (Pa), γ_xy: engineering shear strain (rad), G: Pa. Isotropic, linear elastic.
E = 2G(1 + ν) — Relation among elastic constants; isotropic linear elasticity.
E = 3K(1 − 2ν) — Relation among elastic constants; isotropic linear elasticity.
E = 9KG / (3K + G) — Relation among elastic constants; isotropic linear elasticity.
ν = (3K − 2G) / [2(3K + G)] — Relation among elastic constants; isotropic linear elasticity.
K = − p / (ΔV/V) — Bulk modulus; p: hydrostatic pressure (Pa, positive in compression by fluid convention), ΔV/V: volumetric strain (dimensionless). Uniform hydrostatic stress.
ε_v = (1/E)[(1 − 2ν)(σ_x + σ_y + σ_z)] — Volumetric strain under general triaxial normal stresses; isotropic linear elasticity.
ε_z = − (ν/E)(σ_x + σ_y) — Plane stress out-of-plane strain; σ_z = 0; isotropic linear elasticity.
σ_z = ν(σ_x + σ_y) — Plane strain with ε_z = 0; isotropic linear elasticity.
ε_v = (1 − 2ν)·(σ/E) — Volumetric strain under uniaxial stress σ; isotropic linear elasticity.
Worked examples
Example 1 — Direct application (uniaxial tension with Poisson effect) Given: Steel rod, diameter d = 20 mm, length L = 2.0 m, axial tensile load P = 30 kN. Material: E = 200 GPa, ν = 0.30. Find axial stress, axial extension, lateral contraction in diameter, and change in volume. Assume small strain, uniform stress.
Steps:
- Cross-sectional area: A = π d²/4 = π(0.020 m)²/4 = 3.1416×10⁻⁴ m².
- Axial stress: σ = P/A = 30,000 N / 3.1416×10⁻⁴ m² = 9.549×10⁷ Pa = 95.49 MPa.
- Axial strain: ε = σ/E = 95.49×10⁶ Pa / 200×10⁹ Pa = 4.7745×10⁻⁴.
- Axial extension: ΔL = ε·L = 4.7745×10⁻⁴ × 2.0 m = 9.549×10⁻⁴ m = 0.9549 mm.
- Lateral strain: ε_lat = −ν·ε = −0.30 × 4.7745×10⁻⁴ = −1.432×10⁻⁴.
- Change in diameter: Δd = ε_lat · d = −1.432×10⁻⁴ × 0.020 m = −2.864×10⁻⁶ m = −0.002864 mm.
- Initial volume: V₀ = A·L = 3.1416×10⁻⁴ m² × 2.0 m = 6.2832×10⁻⁴ m³.
- Volumetric strain under uniaxial stress: ε_v = (1 − 2ν)(σ/E) = (1 − 0.6) × 4.7745×10⁻⁴ = 1.9098×10⁻⁴.
- Change in volume: ΔV = ε_v · V₀ = 1.9098×10⁻⁴ × 6.2832×10⁻⁴ m³ = 1.200×10⁻⁷ m³.
Answer: Axial stress = 95.5 MPa; axial extension = 0.955 mm; diameter change = −0.00286 mm; change in volume = 1.20×10⁻⁷ m³.
Example 2 — Combined plane stress with shear; find strains and G Given: Thin plate in plane stress: σ_x = +80 MPa, σ_y = −40 MPa, τ_xy = +30 MPa. Material: E = 210 GPa, ν = 0.28. Find ε_x, ε_y, γ_xy, out-of-plane strain ε_z, and G.
Steps:
- Shear modulus from E, ν: G = E/[2(1 + ν)] = 210×10⁹ Pa / [2(1 + 0.28)] = 210×10⁹ / 2.56 = 8.203×10¹⁰ Pa = 82.03 GPa.
- Plane stress normal strains:
- ε_x = (1/E)[σ_x − νσ_y] = (1/210×10⁹)[80×10⁶ − 0.28(−40×10⁶)] = (91.2×10⁶) / 210×10⁹ = 4.343×10⁻⁴.
- ε_y = (1/E)[σ_y − νσ_x] = (1/210×10⁹)[−40×10⁶ − 0.28(80×10⁶)] = (−62.4×10⁶) / 210×10⁹ = −2.972×10⁻⁴.
- Shear strain: γ_xy = τ_xy / G = 30×10⁶ Pa / 82.03×10⁹ Pa = 3.659×10⁻⁴ rad.
- Out-of-plane strain (σ_z = 0 in plane stress): ε_z = −(ν/E)(σ_x + σ_y) = −(0.28/210×10⁹)(80×10⁶ − 40×10⁶) = −5.333×10⁻⁵.
- Volumetric strain: ε_v = ε_x + ε_y + ε_z = 4.343×10⁻⁴ − 2.972×10⁻⁴ − 5.333×10⁻⁵ = 8.381×10⁻⁵.
Answer: ε_x = 4.343×10⁻⁴; ε_y = −2.972×10⁻⁴; γ_xy = 3.659×10⁻⁴ rad; ε_z = −5.33×10⁻⁵; G = 82.0 GPa.
Common mistakes
- Mixing units (MPa vs Pa). Always convert stresses to Pa when using E in Pa.
- Using degrees instead of radians for shear strain; γ is in radians (dimensionless).
- Confusing engineering shear strain γ with the tensorial shear component ε_xy; remember γ = 2ε_xy.
- Sign errors: forgetting compression is negative under the chosen convention; misapplying Poisson’s ratio sign (lateral contraction should be negative if axial tension is positive).
- Applying plane stress formulas to plane strain (and vice versa), especially for ε_z and σ_z relations.
- Using the wrong area for stress (e.g., using deformed area instead of original engineering area when asked for engineering stress).
- Forgetting that only two elastic constants are independent in isotropic linear elasticity; check which relations apply before substituting.
- Ignoring out-of-plane strain ε_z in plane stress cases; it affects volumetric strain and thickness change.
- Misstating complementary shear: the companion shear on the perpendicular face must be equal in magnitude; otherwise, free-body moment equilibrium fails.
For GATE ME
- Quick conversions among elastic constants: compute G or K or ν from given E and one other constant; manipulate E = 2G(1 + ν) and E = 3K(1 − 2ν), and E = 9KG/(3K + G).
- Volumetric strain problems under hydrostatic pressure or under combined normal stresses; derive ΔV for a block or bar using ε_v.
- Plane stress strain computation: given σ_x, σ_y, τ_xy, find ε_x, ε_y, γ_xy, ε_z; occasionally, the reverse (given strains, find stresses) using generalized Hooke’s law.
- Uniaxial bar deformation: extension, lateral contraction, change in volume; some variants include composite members (covered under Simple Stresses and Strains) — here focus on single, uniform materials.
- Concept checks on ranges and meanings of ν, and the independence of elastic constants; recognition that ν close to 0.5 implies near-incompressibility.
- Complementary shear and the need for equal-magnitude shears on perpendicular planes; tie-in to principal stresses in pure shear (further explored under Principal Stresses and Mohr’s Circle).
- Watch for assumptions: small strain, isotropy, plane stress/strain identification — marks are often lost here.
Quick check
- A homogeneous isotropic bar is in uniaxial tension with ε_longitudinal = 600 µε and ν = 0.3. What is the lateral strain?
- For an isotropic material with E = 200 GPa and ν = 0.25, find G and K.
- Under plane stress, σ_x = 50 MPa, σ_y = 30 MPa, ν = 0.3, E = 210 GPa. What is ε_z?
Answers: (1) ε_lateral = −ν·ε_longitudinal = −180 µε. (2) G = E/[2(1 + ν)] = 80 GPa; K = E/[3(1 − 2ν)] = 133.33 GPa. (3) ε_z = −(ν/E)(σ_x + σ_y) = −(0.3/210×10⁹)(80×10⁶) = −1.143×10⁻⁴.
Finished this topic? Mark it so your progress, study plan and readiness keep up.
Stuck on something here?