Mohr's circle for plane stress and strain

Graphical and analytical method to transform plane stresses/strains, find principal values, maximum shear, and plane orientations using Mohr’s circle.

Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.

Why it matters

Mohr’s circle lets you see at a glance the critical (principal and maximum shear) stresses/strains and the planes on which they act, without cranking through equations for every angle. Designers use it to judge failure risk, orient fibers or cuts, and interpret strain-gauge data — fast and reliably — in plates, shafts, and thin-walled parts under multiaxial loading.

Key ideas

  • Plane states:
    • Plane stress: Only in-plane normal stresses (σx, σy) and in-plane shear (τxy) are significant; out-of-plane stress σz ≈ 0 (thin plates). Assumptions: small deformation, linear elasticity for constitutive links, material possibly isotropic when linking stress and strain.
    • Plane strain: Out-of-plane strain εz ≈ 0 (long bodies with constrained thickness change), but σz generally nonzero.
  • Stress components and sign conventions (used consistently here):
    • Normal stress σ: tensile positive, compressive negative.
    • Shear stress τxy: positive when it acts on the positive x-face in the positive y-direction (the usual ME sign leading to a clockwise tendency of the element). With this convention, when drawing Mohr’s circle of stress, plot τ positive downward. Note: Some texts plot τ upward as positive; if you switch, the sine terms in transformation equations change sign. Be consistent within a problem.
  • Mohr’s circle (stress): A graphical representation of the general 2D stress transformation. Horizontal axis is σ, vertical axis is τ (positive downward under our convention). The state on a plane rotated by physical angle θ from the x-plane appears at a point reached by rotating 2θ around the circle. Key geometric facts:
    • Center C at σ = (σx + σy)/2, τ = 0
    • Radius R = √[ ((σx − σy)/2)² + τxy² ]
    • Points representing the x- and y-faces: A(σx, τxy), B(σy, −τxy). A and B are endpoints of the diameter.
    • Principal stresses occur where τ = 0 (circle intersects the σ-axis). Maximum shear occurs at the top/bottom of the circle (±R from center vertically).
    • Direction mapping: If the physical plane is rotated by +θ counterclockwise from the x-plane, the corresponding point on Mohr’s circle is rotated by 2θ clockwise (because τ is plotted positive downward under our convention). Remember “double the angle, reverse the sense.”
  • Transformation equations (stress) arise from tensor rotation (or equilibrium of a turned element). For a plane rotated by θ counterclockwise from the x-plane:
    • σx′ = (σx + σy)/2 + (σx − σy)/2 cos 2θ + τxy sin 2θ
    • σy′ = (σx + σy)/2 − (σx − σy)/2 cos 2θ − τxy sin 2θ
    • τx′y′ = −(σx − σy)/2 sin 2θ + τxy cos 2θ These produce the circle by eliminating θ (complete the square in σ′ and τ′).
  • Principal stresses and orientations:
    • Principal stresses σ1 ≥ σ2 are the eigenvalues of the 2D stress tensor and lie at C ± R.
    • Principal planes (no shear) are found from tan 2θp = 2τxy / (σx − σy). The two principal planes are 90° apart; θp is usually reported as the smaller-magnitude angle from the x-plane to the σ1-plane (counterclockwise positive by our convention). Use atan2 for correct quadrant.
    • On planes of maximum in-plane shear, τmax = R, and their normals are at θs = θp + 45° from the σ1-plane (i.e., halfway between principal planes). The normal stress on these planes equals the average, (σx + σy)/2.
  • Special/limiting cases (stress):
    • Uniaxial: σx = σ0, σy = 0, τxy = 0 ⇒ C = σ0/2, R = |σ0|/2 ⇒ σ1 = σ0, σ2 = 0, τmax = |σ0|/2 at ±45°.
    • Pure shear: σx = σy = 0, τxy = τ0 ⇒ C = 0, R = |τ0| ⇒ σ1 = +|τ0|, σ2 = −|τ0|, principal planes at ±45° to the shear planes.
    • Equal biaxial: σx = σy = σb ⇒ C = σb, R = |τxy|; if τxy = 0, the circle collapses to a point (hydrostatic state), and all planes see the same normal stress and zero shear.
  • Mohr’s circle (strain) parallels the stress circle but note the shear ordinate uses half the engineering shear strain:
    • Plot ε on the horizontal axis and γ/2 on the vertical axis (again positive downward under the same graphical convention to match algebra). Center Cε = (εx + εy)/2, radius Rε = √[ ((εx − εy)/2)² + (γxy/2)² ].
    • Principal strains: ε1,2 = (εx + εy)/2 ± Rε; orientation: tan 2θp = γxy / (εx − εy) (same θp as stress if material is isotropic and principal axes coincide, but stress-strain linkage is separate).
    • Maximum in-plane shear strain: γmax = 2 Rε; its planes are 45° from the principal strain planes.
  • Linking stress and strain (isotropic, linear elastic):
    • Generalized Hooke’s law in 3D: εx = (1/E)[σx − ν(σy + σz)], εy = (1/E)[σy − ν(σz + σx)], εz = (1/E)[σz − ν(σx + σy)], and γxy = τxy/G with G = E/[2(1 + ν)].
    • Plane stress (σz = 0): εz = −ν/E (σx + σy). Use σx = E/(1 − ν²)(εx + ν εy), σy = E/(1 − ν²)(εy + ν εx), τxy = G γxy.
    • Plane strain (εz = 0): σz = ν(σx + σy). In principal directions: ε1 = (1/E)(σ1 − ν σ2), ε2 = (1/E)(σ2 − ν σ1). Invert to σ1 = E/(1 − ν²)(ε1 + ν ε2), σ2 = E/(1 − ν²)(ε2 + ν ε1).
  • How the circle is derived (outline):
    1. Write σx′, τx′y′ as functions of θ using equilibrium or tensor rotation, yielding cos 2θ and sin 2θ terms.
    2. Subtract the average stress: σx′ − (σx + σy)/2 = (σx − σy)/2 cos 2θ + τxy sin 2θ.
    3. Square and add with τx′y′ expression, rearrange to (σx′ − C)² + (τx′y′)² = R² — the circle equation.
  • Why real devices differ from the ideal:
    • Thickness and 3D effects: real plates may have through-thickness gradients; near holes/notches (see Stress Concentration), stress is 3D.
    • Material anisotropy or plasticity: principal stress and strain directions can deviate; Hooke’s isotropy constants do not apply.
    • Large rotations: Mohr’s circle assumes small deformation kinematics and linear superposition; at large strains, definitions of shear and rotation change.

Formulas

C = (σx + σy) / 2 Center of Mohr’s stress circle; σx, σy in Pa; applies to plane stress.

R = √[ ((σx − σy)/2)² + τxy² ] Radius of Mohr’s stress circle; τxy in Pa; plane stress.

σ1,2 = C ± R Principal stresses; Pa; plane stress.

tan 2θp = 2 τxy / (σx − σy) Orientation of principal stress planes; θp in radians or degrees; use atan2(2τxy, σx − σy) for quadrant; plane stress; counterclockwise positive.

τmax = R Maximum in-plane shear stress; Pa; occurs on planes at θs = θp + 45° from the σ1-plane.

σn on max-shear planes = (σx + σy) / 2 Normal stress on the planes of maximum shear; Pa; plane stress.

σx′ = (σx + σy)/2 + (σx − σy)/2 cos 2θ + τxy sin 2θ Normal stress on a plane rotated by θ (CCW) from x-plane; Pa; plane stress with τ plotted downward positive in Mohr’s construction.

τx′y′ = −(σx − σy)/2 sin 2θ + τxy cos 2θ Shear stress on a plane rotated by θ (CCW) from x-plane; Pa; same sign convention as above.

Cε = (εx + εy) / 2 Center of Mohr’s strain circle; strain is dimensionless.

Rε = √[ ((εx − εy)/2)² + (γxy/2)² ] Radius of strain circle; engineering shear strain γxy dimensionless.

ε1,2 = Cε ± Rε Principal strains; dimensionless; plane strain or plane stress kinematics.

γmax = 2 Rε Maximum in-plane shear strain; dimensionless.

tan 2θp = γxy / (εx − εy) Orientation of principal strain planes; θp measured CCW from x-plane; dimensionless inputs.

εx′ = (εx + εy)/2 + (εx − εy)/2 cos 2θ + (γxy/2) sin 2θ Normal strain on a plane at θ; dimensionless; small-strain assumption.

γx′y′/2 = −(εx − εy)/2 sin 2θ + (γxy/2) cos 2θ Shear strain on a plane at θ (engineering measure); dimensionless.

G = E / [2(1 + ν)] Shear modulus for isotropic materials; Pa; linear elasticity.

Plane stress: σx = E/(1 − ν²) (εx + ν εy), σy = E/(1 − ν²) (εy + ν εx), τxy = G γxy Stress–strain link under plane stress; SI units: Pa; isotropic linear elastic.

Plane strain: σz = ν (σx + σy) Out-of-plane stress under plane strain; Pa; isotropic linear elastic.

Plane stress: εz = −ν/E (σx + σy) Out-of-plane strain under plane stress; dimensionless; isotropic linear elastic.

Worked examples

Example 1 — Direct: Principal stresses, max shear, and orientations from σx, σy, τxy Given: σx = 80 MPa (tension), σy = −20 MPa (compression), τxy = +30 MPa. Assume plane stress, small deformations, sign convention as stated (τ plotted downward positive in Mohr’s circle).

  1. Center and radius
  • Formula: C = (σx + σy)/2; R = √[ ((σx − σy)/2)² + τxy² ]
  • Numbers: C = (80 − 20)/2 = 30 MPa; (σx − σy)/2 = (80 − (−20))/2 = 50 MPa; R = √(50² + 30²) MPa = √(2500 + 900) MPa = √3400 MPa ≈ 58.31 MPa.
  1. Principal stresses
  • Formula: σ1,2 = C ± R
  • Numbers: σ1 = 30 + 58.31 = 88.31 MPa; σ2 = 30 − 58.31 = −28.31 MPa.
  1. Maximum in-plane shear stress and normal stress on shear planes
  • Formula: τmax = R; σn on max-shear planes = (σx + σy)/2
  • Numbers: τmax = 58.31 MPa; σn = 30 MPa.
  1. Orientation of principal planes
  • Formula: tan 2θp = 2 τxy / (σx − σy)
  • Numbers: tan 2θp = (2×30)/(80 − (−20)) = 60/100 = 0.6 ⇒ 2θp = arctan(0.6) ≈ 30.964° ⇒ θp ≈ 15.48° (measured CCW from x-plane to σ1-plane under our convention). The σ2-plane is at θp + 90° ≈ 105.48°. Max-shear planes are at θp ± 45° ≈ 60.48° and −29.52°.

Answer: σ1 ≈ 88.31 MPa, σ2 ≈ −28.31 MPa, τmax ≈ 58.31 MPa; σ1-plane ≈ 15.48° CCW from x-plane.

Example 2 — GATE-style: From measured strains to principal strains, orientations, and principal stresses A thin isotropic steel plate is under plane stress. Measured engineering strains: εx = +800 με, εy = −200 με, γxy = +600 με. Material: E = 210 GPa, ν = 0.30. Find (a) ε1, ε2 and their directions, γmax; (b) σ1, σ2 (principal stresses).

Given: εx = 800×10⁻⁶, εy = −200×10⁻⁶, γxy = 600×10⁻⁶; E = 210 GPa, ν = 0.30. Assume small strains, linear isotropic elasticity, plane stress.

(a) Principal strains and orientations

  1. Center and radius of strain circle
  • Formula: Cε = (εx + εy)/2; Rε = √[ ((εx − εy)/2)² + (γxy/2)² ]
  • Numbers: Cε = (800 − 200)/2 ×10⁻⁶ = 300×10⁻⁶; (εx − εy)/2 = (800 − (−200))/2 ×10⁻⁶ = 500×10⁻⁶; γxy/2 = 300×10⁻⁶.
  • Rε = √[(500×10⁻⁶)² + (300×10⁻⁶)²] = √(250000 + 90000)×10⁻¹² = √340000×10⁻⁶ ≈ 583.095×10⁻⁶.
  1. Principal strains
  • Formula: ε1,2 = Cε ± Rε
  • Numbers: ε1 = 300×10⁻⁶ + 583.095×10⁻⁶ = 883.095×10⁻⁶; ε2 = 300×10⁻⁶ − 583.095×10⁻⁶ = −283.095×10⁻⁶.
  1. Orientation
  • Formula: tan 2θp = γxy / (εx − εy)
  • Numbers: tan 2θp = 600×10⁻⁶ / (1000×10⁻⁶) = 0.6 ⇒ 2θp = arctan(0.6) ≈ 30.964° ⇒ θp ≈ 15.48° CCW from x-plane to ε1-plane. The ε2-plane is at θp + 90° ≈ 105.48°.
  1. Maximum in-plane shear strain
  • Formula: γmax = 2 Rε
  • Numbers: γmax = 2 × 583.095×10⁻⁶ = 1.16619×10⁻³ = 1166.19 με.

(b) Principal stresses (plane stress) We can work in principal strain directions (no shear) using isotropic relations.

  1. Constitutive relation in principal directions
  • Formula: σ1 = E/(1 − ν²)(ε1 + ν ε2), σ2 = E/(1 − ν²)(ε2 + ν ε1)
  • Numbers: E/(1 − ν²) = 210 GPa / (1 − 0.3²) = 210/0.91 GPa ≈ 230.769 GPa.
    • ε1 + ν ε2 = 883.095×10⁻⁶ + 0.3×(−283.095×10⁻⁶) = 883.095×10⁻⁶ − 84.9285×10⁻⁶ = 798.1665×10⁻⁶.
    • ε2 + ν ε1 = −283.095×10⁻⁶ + 0.3×883.095×10⁻⁶ = −283.095×10⁻⁶ + 264.9285×10⁻⁶ = −18.1665×10⁻⁶.
  1. Compute σ1, σ2
  • σ1 = 230.769×10⁹ × 798.1665×10⁻⁶ Pa ≈ 184.19×10⁶ Pa = 184.19 MPa.
  • σ2 = 230.769×10⁹ × (−18.1665×10⁻⁶) Pa ≈ −4.19×10⁶ Pa = −4.19 MPa.

Optional cross-check (not required): τxy = G γxy with G = E/[2(1 + ν)] = 210 GPa / 2.6 ≈ 80.769 GPa ⇒ τxy ≈ 80.769×10⁹ × 600×10⁻⁶ ≈ 48.46 MPa. Using σx = E/(1 − ν²)(εx + ν εy) and σy = E/(1 − ν²)(εy + ν εx), one finds σx ≈ 170.77 MPa, σy ≈ 9.23 MPa; Mohr’s circle from these yields principal stresses close to 184.19 MPa and −4.19 MPa (small differences from rounding).

Final answers: ε1 ≈ 883.10 με at θp ≈ 15.48° CCW from x, ε2 ≈ −283.10 με at θp + 90°; γmax ≈ 1166.19 με; σ1 ≈ 184.19 MPa, σ2 ≈ −4.19 MPa.

Common mistakes

  • Inconsistent shear sign: taking τ positive upward while using equations derived for τ positive downward (or vice versa).
  • Using engineering shear strain γ directly in the strain circle ordinate instead of γ/2.
  • Dropping the average term: trying to take σ1,2 as ±R instead of C ± R.
  • Not using atan2 for tan 2θp, leading to a 90° or 180° orientation error.
  • Mixing plane stress and plane strain constitutive links (e.g., using E/(1 − ν²) incorrectly for a plane strain stress from εx, εy without care).
  • Unit slips: forgetting that strains are dimensionless (με = 10⁻⁶), or mixing MPa with Pa.

For GATE ME

  • Direct computation of principal stresses/strains and maximum shear from given σx, σy, τxy (or εx, εy, γxy), including orientations using tan 2θp.
  • Transformation at a specified angle: compute σx′, τx′y′ or εx′, γx′y′ at θ = given degrees.
  • Special cases: uniaxial, pure shear, equal biaxial, and identification of hydrostatic states (circle radius zero).
  • Strain-to-stress conversion in plane stress using E, ν; principal strain use to find principal stresses quickly.
  • Conceptual checks: normal stress on max-shear planes equals average stress; principal planes are orthogonal; max-shear planes are 45° from principal planes.
  • Graphical reasoning: identifying center, radius, and mapping rotations (2θ, reverse sense) on Mohr’s circle. Practice: quick mental center/radius estimates, careful atan2 usage, converting με to strain, and keeping a consistent sign convention throughout a problem.

Quick check

  1. A state of pure shear has τxy = 50 MPa, σx = σy = 0. What are σ1, σ2 and the principal plane orientations?
  2. In uniaxial tension σx = 120 MPa (σy = τxy = 0), what is τmax and at what plane orientation does it occur?
  3. If εx = εy = ε0 and γxy ≠ 0, what are ε1, ε2 and the orientation of principal strain planes?

Answers: (1) σ1 = +50 MPa, σ2 = −50 MPa; principal planes at ±45° to the original x-plane. (2) τmax = 60 MPa on planes at ±45° to the x-plane, with normal stress σn = 60 MPa there. (3) ε1,2 = ε0 ± |γxy|/2; principal strain planes at ±45° from the original axes (direction depends on sign of γxy).

Finished this topic? Mark it so your progress, study plan and readiness keep up.

Stuck on something here?