Interference in thin films
Interference in thin films: phase change on reflection, path difference 2·n·t·cos r, conditions for bright/dark in reflected/transmitted light, wedge fringes, Newton’s rings, and anti-reflection coatings.
Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.
Why it matters
Key ideas
- Refractive index (n): Ratio of speed of light in vacuum to that in the medium. It sets the wavelength in the medium as λ = λ₀/n, where λ₀ is the wavelength in vacuum/air.
- Phase change on reflection (π-shift rule): When light reflects from an interface going from a medium of lower refractive index to higher refractive index, the reflected wave suffers a phase reversal of π (equivalent to an extra path of λ/2). Reflection from higher to lower refractive index produces no phase reversal. Transmission never causes such jump; it only accumulates phase from propagation through thickness.
- Geometry and angles: Light of angle of incidence i enters the film at angle of refraction r, related by Snell’s law n₁·sin i = n₂·sin r. Inside the film, the optical path difference between the two main reflected (or transmitted) rays is governed by the double pass 2·n·t·cos r.
Exact statements and standard derivations
- Condition for interference in a uniform thin film (two-beam model)
- Assumptions: monochromatic, coherent light; transparent, non-absorbing film of refractive index n and thickness t; smooth, plane-parallel interfaces; multiple higher-order internal reflections are neglected (two-beam approximation, valid for weak reflectance). Air outside has n ≈ 1.
- Path difference: The second reflected ray traverses down and up inside the film. The physical path length inside the film is 2·t/ cos r along the ray, but after accounting for the equalization of emerging rays the net optical path difference is OPD = 2·n·t·cos r (measured relative to vacuum/air wavelength λ₀).
- Phase reversal term: Add an extra λ₀/2 to the OPD when there is exactly one phase reversal among the two interfering reflected rays (i.e., one reflection occurs from a lower-to-higher index and the other from higher-to-lower). If there are zero or two reversals, do not add λ₀/2.
Reflected light (two-beam):
- Constructive (bright): • If one phase reversal: 2·n·t·cos r = (m + 1/2)·λ₀, m = 0, 1, 2, … • If zero or two reversals: 2·n·t·cos r = m·λ₀.
- Destructive (dark): opposite of the above cases.
Transmitted light (two-beam):
- Constructive (bright): • If one phase reversal at reflection: 2·n·t·cos r = m·λ₀. • If zero or two reversals: 2·n·t·cos r = (m + 1/2)·λ₀.
- Note: “Opposite” conditions arise because the reflected pair and transmitted pair differ in their relative phase by π when energy is conserved in a lossless film.
What to draw (uniform film at oblique incidence):
- Draw two horizontal parallel lines as film boundaries. Label top medium n₁, film n, bottom medium n₃. Show incident ray at angle i to the normal, refracted ray inside at angle r, using a normal line to the interfaces. Mark two reflected rays: one from top interface and one returning from bottom. Label thickness t, angle r inside film, and indicate the extra optical path 2·n·t·cos r. Add a note: “π phase shift at reflection from lower to higher n.”
- Wedge-shaped film and straight fringes
- Wedge-shaped film: Two surfaces enclosing a small angle α (in radians), forming a film whose thickness increases linearly along x: for small α, t(x) ≈ x·α.
- Typical setup: Two glass plates with a spacer at one end create an air wedge (n ≈ 1). Light is incident nearly normal; fringes are localized near the wedge and appear as straight, equally spaced dark and bright bands parallel to the line of contact.
- Phase reversal: For an air wedge between glass plates, reflection at the top glass–air interface (viewed from air) involves lower-to-higher index at the first reflecting surface of the thin air film, and higher-to-lower at the second; net is one phase reversal for the two reflected rays. Hence, in reflected light, there is a dark fringe at the contact (t = 0).
- Conditions (normal incidence, air film): • Dark (reflected): 2·t = m·λ (here λ ≈ λ₀ in air), m = 0, 1, 2, … • Bright (reflected): 2·t = (m + 1/2)·λ.
- Fringe spacing (interfringe distance β): Using t = x·α and the dark condition, successive dark fringes at positions x_m satisfy 2·x_m·α = m·λ, so β = x_{m+1} − x_m = λ/(2·α), approximately constant for small α.
What to draw (wedge):
- Two long plates making a small angle α. Mark a thin spacer at one end. Show incident light and two reflected rays. Draw straight fringes parallel to the contact. Label t = x·α and indicate that the first dark fringe occurs at contact (x = 0).
- Newton’s rings (circular fringes)
- Setup: A plano-convex lens of large radius of curvature R placed on a flat glass plate forms a thin air film of varying thickness between them. Illumination is typically with monochromatic, collimated light, observed in reflection (dark center) or transmission (bright center for the same order).
- Geometry: For distance r from the point of contact, the thickness of the air film is t ≈ r²/(2·R) (lens sagitta formula, valid when r ≪ R).
- Reflected-light conditions (one phase reversal): • Dark rings: 2·t = m·λ ⇒ r_m² = m·λ·R, m = 0, 1, 2, … (m = 0 gives dark center) • Bright rings: 2·t = (m + 1/2)·λ ⇒ r_m² = (m + 1/2)·λ·R
- Diameters: D_m² = 4·m·λ·R (dark), and D_m² = 4·(m + 1/2)·λ·R (bright).
- In transmitted light, bright and dark conditions interchange.
What to draw (Newton’s rings):
- A plano-convex lens resting on a flat plate. Show circular fringes centered at contact. Label R (radius of curvature), r (radial distance), and t = r²/(2·R). Indicate dark center in reflection.
- Anti-reflection coating (quarter-wave film)
- Goal: Minimize reflected intensity at a design wavelength λ₀ for light from air onto a high-index substrate.
- Common design: A single-layer film of refractive index n_f between air (≈1) and substrate n_s, with n_s > n_f > 1, and thickness t = λ₀/(4·n_f).
- Reason: Reflections from the air–film and film–substrate interfaces have equal π phase reversals (two in total, net zero), but the extra optical path inside the film makes them out of phase by π when 2·n_f·t = λ₀/2. Amplitude matching is optimized when n_f ≈ √(n_air·n_s).
Other notes
- White-light illumination produces colored patterns because the bright/dark conditions depend on wavelength; different wavelengths satisfy conditions at different thicknesses.
- At oblique incidence, always use cos r (inside-film angle), not cos i.
- Multi-beam effects (Fabry–Pérot) produce sharper fringes when reflectivity is high; this note focuses on the standard two-beam model unless stated.
Formulas
n₁·sin i = n₂·sin r— Snell’s law: i is incidence angle, r refraction angle, n₁, n₂ refractive indices (dimensionless). Use to find r.OPD = 2·n·t·cos r— optical path difference from double pass inside film of index n and thickness t (m), for internal angle r (radians). Two-beam approximation.- Reflected-light conditions (two-beam):
• With one phase reversal:
2·n·t·cos r = (m + 1/2)·λ₀(bright),2·n·t·cos r = m·λ₀(dark); m = 0, 1, 2, … • With zero or two reversals:2·n·t·cos r = m·λ₀(bright),2·n·t·cos r = (m + 1/2)·λ₀(dark). - Transmitted-light conditions (two-beam): opposite to reflected-light conditions given above.
- Wedge thickness:
t(x) ≈ x·α— small-angle wedge with wedge angle α (radians) along distance x (m) from contact. - Wedge interfringe spacing (reflected, air film, near-normal incidence):
β = λ / (2·α)— β (m) is distance between successive dark (or bright) fringes. - Newton’s rings thickness:
t = r² / (2·R)— r is ring radius (m), R is lens radius of curvature (m). - Newton’s rings (reflected):
r_m² = m·λ·Rfor dark rings;r_m² = (m + 1/2)·λ·Rfor bright rings. Diameters:D_m² = 4·m·λ·R(dark). - Quarter-wave anti-reflection thickness:
t = λ₀ / (4·n_f)— n_f is coating index (dimensionless). Best amplitude match whenn_f ≈ √(n_s)for n_air ≈ 1.
Constants
- Speed of light in vacuum: c = 2.99792458 × 10⁸ m·s⁻¹ (exact, SI definition).
Worked examples
Example 1: Minimum thickness for anti-reflection at normal incidence
- Given: Glass substrate n_s = 1.52, coating MgF₂ with n_f = 1.38, design wavelength λ₀ = 550 nm, normal incidence (r = 0, cos r = 1).
- Required: Minimum thickness t for zero reflection at λ₀.
- Formula: t = λ₀ / (4·n_f).
- Steps:
- Substitute values: t = (550 × 10⁻⁹ m) / (4 × 1.38).
- Compute denominator: 4 × 1.38 = 5.52.
- t = 550e−9 / 5.52 m = 99.64 × 10⁻⁹ m.
- Answer: t = 9.964 × 10⁻⁸ m ≈ 100 nm (minimum thickness) — bold: 1.00 × 10⁻⁷ m.
Example 2: Fringe spacing in an air wedge
- Given: Monochromatic light λ = 589 nm (sodium D-line), wedge angle α = 0.050°, normal incidence; air film so n ≈ 1.
- Required: Interfringe spacing β between successive dark fringes in reflected light.
- Convert α to radians: α = 0.050° × (π/180) = 8.7266 × 10⁻⁴ rad (approx.).
- Formula: β = λ / (2·α).
- Steps:
- β = (589 × 10⁻⁹ m) / (2 × 8.7266 × 10⁻⁴).
- Denominator = 1.74532 × 10⁻³.
- β = 589e−9 / 1.74532e−3 m = 3.376 × 10⁻⁴ m.
- Answer: β = 3.38 × 10⁻⁴ m ≈ 0.338 mm.
Example 3: Diameter of the 10th dark Newton’s ring (reflected light)
- Given: λ = 546 nm (green mercury line), radius of curvature R = 1.00 m. Find diameter D₁₀ of the 10th dark ring in reflected light.
- Formula: D_m² = 4·m·λ·R (for dark rings in reflection).
- Steps:
- D₁₀² = 4 × 10 × (546 × 10⁻⁹ m) × (1.00 m) = 21.84 × 10⁻⁶ m² = 2.184 × 10⁻⁵ m².
- D₁₀ = √(2.184 × 10⁻⁵) m.
- Compute: √2.184 ≈ 1.478; √10⁻⁵ = 3.162 × 10⁻³.
- D₁₀ ≈ 1.478 × 3.162 × 10⁻³ m = 4.67 × 10⁻³ m.
- Answer: D₁₀ = 4.67 × 10⁻³ m = 4.67 mm.
Common mistakes
- Mixing wavelengths: using λ inside the film but also multiplying by n again; or using λ₀ in one step and λ in another without consistency. A safe rule: keep λ₀ in formulas that already include n explicitly (2·n·t·cos r = m·λ₀ or (m+1/2)·λ₀).
- Confusing order numbering m: whether m = 0 corresponds to the central dark or bright fringe depends on phase reversal and on whether observing reflection or transmission (e.g., Newton’s rings have a dark center in reflection).
- Ignoring small-angle approximations’ limits: t ≈ x·α and t ≈ r²/(2·R) are valid only for small α and r ≪ R.
- Forgetting that in an air wedge (reflected light) the contact is dark (t = 0), not bright.
- For anti-reflection coatings, forgetting the amplitude condition n_f ≈ √(n_s), which affects residual reflectance even if thickness is correct.
For your exam
- Derivations commonly asked:
- Derive OPD = 2·n·t·cos r and obtain conditions for maxima/minima in reflected light for (i) one phase reversal and (ii) zero/two phase reversals.
- Wedge fringes: derive β = λ/(2·α) and explain why the fringe at contact is dark in reflection.
- Newton’s rings: derive r_m² = m·λ·R and D_m² = 4·m·λ·R for reflected light. Comment on transmitted light.
- Anti-reflection coating: derive t = λ₀/(4·n_f) and n_f ≈ √(n_s) for minimal reflectance at λ₀.
- Diagrams: neat, large, with normals and angles labelled; show ray paths, thickness t, angles i and r, and indicate where phase reversal occurs. For Newton’s rings, show the lens–plate contact and circular fringes.
- Numericals: carry units throughout, convert degrees to radians for α, and be explicit about whether λ or λ₀ is used. State assumptions (normal incidence, air film, two-beam approximation, small-angle approximations) before solving.
- Short notes: colors in soap films with white light; effect of oblique incidence; difference between reflected and transmitted patterns.
Quick check
- In a uniform film of index n at angle r inside the film, what OPD enters the interference condition? State also when you must add λ₀/2.
- For Newton’s rings in reflected light, is the central spot bright or dark, and why?
- A single-layer AR coating of index n_f is deposited on glass (n_s). What thickness minimizes reflection at λ₀, and what index n_f gives best cancellation of amplitudes?
Answers: (1) OPD = 2·n·t·cos r; add λ₀/2 when there is exactly one phase reversal between the two reflected rays. (2) Dark, because at t = 0 there is one phase reversal in reflection, giving destructive interference. (3) t = λ₀/(4·n_f); optimal n_f �� √(n_s) for air–film–substrate.
Finished this topic? Mark it so your progress, study plan and readiness keep up.
Stuck on something here?