First Year Engineering is coming soon

We're still writing and reviewing the notes for every subject, and we'll open it when every subject is ready. Meanwhile you can practise aptitude, ask Aria about any subject, or see the branches that are ready.

Hall effect

Hall effect: transverse electric field and voltage in a current-carrying conductor/semiconductor placed in a perpendicular magnetic field; used to find carrier type, concentration, mobility, and to sense magnetic fields.

Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.

Why it matters

Engineers use the Hall effect to measure magnetic fields (Hall sensors in motors, automotive wheel speed, smartphones), and to characterize materials (finding carrier type, carrier concentration, and mobility in conductors and semiconductors). It also helps diagnose device behavior in electronics and is a standard lab method in materials and semiconductor process control.

Key ideas

  • Physical origin: moving charge carriers with drift velocity are deflected sideways by the magnetic Lorentz force until a steady-state transverse electric field builds up to balance that magnetic deflection.

  • Exact statement (Hall effect)

    • When a current density J flows in a conductor or semiconductor and a magnetic flux density B is applied perpendicular to J, a transverse electric field E_H appears such that E_H is proportional to the product of J and the perpendicular component of B. The proportionality constant is the Hall coefficient R_H.
  • Fundamental forces and drift

    • Bold definition: Lorentz force is the force on a charge q moving with velocity v in electric field E and magnetic field B: F = q(E + v × B). Assumption: classical, nonrelativistic speeds, uniform fields.
    • Bold definition: drift velocity v_d is the average velocity of charge carriers along the direction of current due to an applied electric field. For a single carrier type of density n and charge q, current density is J = n q v_d (magnitude if all are same sign carriers).
  • Hall balance and Hall field

    • In steady state, the net transverse force on carriers is zero: q E_y + q(v_d × B)_y = 0. For J along +x and B along +z, v_d × B points along −y; the magnetic force q(v_d × B) points along ±y depending on the sign of q. The steady transverse field E_y (the Hall field) balances the magnetic force.
    • Therefore E_y = −(v_d × B)_y. For a simple orthogonal case with v_d along x and B along z, magnitude E_y = v_d B (sign depends on carrier sign and field directions).
  • Bold definition: Hall coefficient R_H

    • Exact statement (single carrier type): R_H is defined by E_y = R_H J_x B_z, with R_H = 1/(n q). Assumptions: uniform sample; single dominant carrier type; low magnetic fields so that J remains along x (small Hall angle); classical transport.
    • Sign of R_H indicates carrier type: negative for electrons (q = −e), positive for holes (q = +e). Elementary charge e = 1.602176634 × 10^−19 C.
    • Units: R_H in m^3/C.
  • Bold definition: Hall voltage V_H

    • The Hall voltage is the potential difference across the width w due to E_y: V_H = E_y w. Using J_x = I/(w t) and E_y = R_H J_x B_z, we get V_H = (R_H I B_z)/t. Assumptions: uniform current density; thickness t measured along magnetic field direction; contacts sample full width.
    • Width w cancels out in the ideal formula, so V_H does not depend on w for a rectangular sample with uniform current.
  • Bold definition: Hall angle θ_H

    • Exact statement (Drude model): tan θ_H = E_y/E_x = μ_H B for a single carrier type, where μ_H = R_H σ is the signed Hall mobility and B is perpendicular to current. Assumptions: low-field, classical scattering with relaxation time τ; mobility magnitude μ = |q| τ/m*, so in magnitude |tan θ_H| = μ B; isotropic effective mass m*. At low fields, θ_H is small and current is nearly along x.
  • Bold definition: Mobility μ and its Hall relation

    • Mobility μ is defined by drift velocity per unit electric field: v_d = μ E_x (for the carrier). Conductivity σ = n |q| μ (single carrier type). Combining with R_H = 1/(n q) gives μ = σ |R_H| = |R_H|/ρ. Some texts keep the sign and write μ_H = R_H σ as the signed Hall mobility; exam answers should state the convention used.
  • Semiconductors vs metals

    • In metals, n is very large (∼10^28 m^−3), so |R_H| is small and Hall voltages are small; R_H is usually negative (electron-like) but can be positive in some metals due to complex band structures (multiple carrier types).
    • In doped semiconductors, n (or p) is much lower (∼10^20–10^22 m^−3), giving larger |R_H| and measurable Hall voltages. The sign of R_H directly gives n-type (negative) or p-type (positive). With both carriers present (intrinsic or compensated doping), the simple formula R_H = 1/(n q) does not apply; a two-carrier expression is needed, and a Hall factor r_H (≈ 1 for many scattering mechanisms) may appear.
  • Measurement of magnetic field

    • From V_H = (R_H I B)/t, if R_H, I, and t are known, a calibrated Hall sensor can measure B directly, including field polarity by sign of V_H.
  • What to draw and label (exam diagram)

    • Draw a rectangular slab. Label length along x, width w along y, thickness t along z. Draw current I entering at left face (x = 0) and exiting at right face (x = L). Draw magnetic field B by arrows pointing upward out of the top face or along +z (perpendicular to current). Show accumulation of charges on the top and bottom edges along y (e.g., negative on one side, positive on the other, depending on carrier type). Mark two small Hall voltage contacts on the sides across width w; label the measured Hall voltage V_H. Indicate E_y direction inside due to Hall field.
  • Typical derivations to prepare

    1. Derive Hall coefficient: Start with Lorentz force balance in y: q E_y + q v_d B = 0 → E_y = −v_d B. Replace v_d by J/(n q). Define R_H by E_y = R_H J B. Hence R_H = 1/(n q) (with sign of q). 2) Derive Hall voltage: V_H = E_y w = R_H (I/(w t)) B w = (R_H I B)/t. 3) Show μ = σ |R_H| (or μ_H = R_H σ if signed), using σ = n |q| μ and R_H = 1/(n q).

Formulas

  • E_y = R_H·J_x·B_z — Definition of Hall coefficient; E_y in V/m, J_x in A/m², B_z in T, R_H in m³/C; B perpendicular to current; single carrier or as a definition in general.
  • R_H = 1/(n·q) — Hall coefficient for a single carrier type; n in m⁻³, q in C; sign of R_H is sign of q; fails when both electrons and holes conduct significantly.
  • V_H = (R_H·I·B)/t — Hall voltage across width; V_H in V, R_H in m³/C, I in A, B in T, t in m; rectangular slab, uniform current, B perpendicular to current and along thickness.
  • tan(θ_H) = E_y/E_x = μ_H·B — Hall angle in Drude model (signed), where μ_H = R_H·σ; in magnitude, |tan θ_H| = μ·B with μ ≥ 0; θ_H dimensionless, μ in m²/(V·s), B in T; low-field condition μB ≪ 1 typically.
  • σ = n·|q|·μ — Conductivity for single carrier; σ in S/m, n in m⁻³, |q| in C, μ in m²/(V·s); neglecting multiband effects.
  • μ = σ·|R_H| = |R_H|/ρ — Mobility from Hall and resistivity; μ in m²/(V·s), σ in S/m, ρ in Ω·m; single dominant carrier.
  • B = (t·V_H)/(R_H·I) — Magnetic field from measured Hall voltage; B in T; sensor mode with known R_H, I, t.

Worked examples

  1. Hall voltage of a doped silicon sample Given: n-type Si bar, carrier concentration n = 5.0 × 10^21 m⁻³; thickness t = 0.30 mm; width w = 5.0 mm; current I = 20 mA; magnetic field B = 0.80 T (perpendicular to current, along +z). Find Hall voltage V_H and its sign.

Steps:

  1. Hall coefficient (single electron carriers): R_H = 1/(n q), with q = −e = −1.602176634 × 10^−19 C.
  2. Compute magnitude |R_H| = 1/(n e) = 1 / [(5.0 × 10^21)(1.602176634 × 10^−19)] m³/C.
  3. Use V_H = (R_H I B)/t; check sign from R_H.

Calculations:

  • Denominator for |R_H|: (5.0 × 10^21)(1.602176634 × 10^−19) = 5.0 × 1.602176634 × 10^(21−19) = 8.01088317 × 10^2 = 801.088317.
  • |R_H| = 1 / 801.088317 ≈ 1.2483 × 10^−3 m³/C.
  • R_H = −1.2483 × 10^−3 m³/C (negative for electrons).
  • Convert t = 0.30 mm = 0.00030 m; I = 20 mA = 0.020 A; B = 0.80 T.
  • V_H = (R_H I B)/t = [ (−1.2483 × 10^−3 m³/C) × (0.020 A) × (0.80 T) ] / (0.00030 m).
  • Numerator: (−1.2483 × 10^−3) × 0.020 × 0.80 = (−1.2483 × 10^−3) × 0.016 = −1.9973 × 10^−5 (units m³·A·T/C).
  • Divide by t: (−1.9973 × 10^−5) / 3.0 × 10^−4 = −0.066577 ≈ −6.6577 × 10^−2 V.

Answer: V_H ≈ −0.0666 V (−66.6 mV). Negative sign corresponds to electron carriers accumulating on one side consistent with n-type.

  1. Carrier concentration from measured Hall coefficient A thin metallic sample has measured Hall coefficient R_H = −7.0 × 10^−11 m³/C at room temperature. Assuming a single electron-like carrier, estimate carrier concentration n.

Steps:

  1. Use R_H = 1/(n q) → n = 1/(R_H q). For electrons, q = −e. We can use magnitudes since the sign only tells the carrier type.
  2. Compute n = 1 / (|R_H| e).

Calculations:

  • |R_H| = 7.0 × 10^−11 m³/C; e = 1.602176634 × 10^−19 C.
  • n = 1 / [ (7.0 × 10^−11)(1.602176634 × 10^−19) ] m⁻³.
  • Denominator: 7.0 × 1.602176634 × 10^(−11−19) = 11.2152364 × 10^−30 = 1.12152364 × 10^−29.
  • n = 1 / (1.12152364 × 10^−29) ≈ 8.92 × 10^28 m⁻³.

Answer: n ≈ 8.9 × 10^28 m⁻³ (typical electron concentration in metals), with negative R_H indicating electron-like carriers.

  1. Mobility from resistivity and Hall data (semiconductor) A p-type semiconductor wafer has resistivity ρ = 0.50 Ω·cm and Hall coefficient R_H = +4.0 × 10^−4 m³/C. Find the mobility μ of the majority carriers. State any conversions used.

Steps:

  1. Convert ρ to SI: 0.50 Ω·cm = 0.50 × 10^−2 Ω·m = 5.0 × 10^−3 Ω·m.
  2. Use μ = |R_H|/ρ for single carrier type (equivalently μ = σ|R_H| with σ = 1/ρ).

Calculations:

  • μ = (4.0 × 10^−4 m³/C) / (5.0 × 10^−3 Ω·m) = 0.080 (m³/(C·Ω·m)).
  • Note that 1 Ω = 1 V/A, and 1 C·Ω = V·s; using σ·R_H analysis gives units m²/(V·s) as required. Numerically: μ = 0.080 m²/(V·s).
  • Convert to the common semiconductor unit cm²/(V·s): 0.080 m²/(V·s) × 10^4 cm²/m² = 800 cm²/(V·s).

Answer: μ ≈ 0.080 m²/(V·s) (that is, 800 cm²/(V·s)) for holes (positive R_H indicates p-type).

Common mistakes

  • Using R_H = 1/(n q) when both electrons and holes contribute: In intrinsic or compensated semiconductors, the simple formula fails; a two-carrier model is needed.
  • Unit errors: Forgetting to convert mm to m or Ω·cm to Ω·m, or misreporting mobility units (should be m²/(V·s) in SI).
  • Confusing μ = σR_H with μ = |R_H|/ρ: Both are correct for a single carrier; since σ = 1/ρ, they are the same. If you use a signed R_H, be clear whether you mean signed Hall mobility μ_H = R_H σ or the conventional positive mobility magnitude μ = |R_H|/ρ.
  • Orientation errors in diagrams: B must be perpendicular to current; if B is parallel to current, there is no Hall effect.
  • Forgetting assumptions: Low-field limit (μB ≪ 1) is often assumed so that current remains along x and E_y ∝ B. At very high B, more complex behavior appears.

For your exam

  • Derivations: Derive R_H = 1/(n q) from Lorentz force balance; derive V_H = (R_H I B)/t for a rectangular sample; derive μ = σ|R_H| using σ = n|q|μ and R_H.
  • Diagrams: Rectangular sample with I, B, charge accumulation, E_y, and Hall contacts labeled; arrows for directions. Explain sign of V_H for n-type vs p-type.
  • Numericals: Compute V_H from given I, B, t, and n; compute n from given R_H; compute μ from given R_H and ρ; compute B from measured V_H for a Hall sensor.
  • What a full-marks answer includes: Clear labeled diagram; correct formulas with symbols defined and SI units; step-by-step derivation with assumptions (single carrier, uniform fields, steady state, low-field limit); correct sign discussion; numericals with units at each step and a boxed or clearly stated final answer.

Quick check

  1. A rectangular p-type sample carries current along x and is placed in a magnetic field along +z. Which side (±y) becomes at higher potential? Why?
  2. Write the formula for Hall voltage in a rectangular slab and define each symbol with SI units.
  3. A metal has R_H = +1.0 × 10^−10 m³/C. What does the sign suggest about the dominant charge carriers?

Answers: 1) For holes (positive carriers), v_d × B points along −y, so positive charge accumulates at −y, making the −y side higher potential than +y. 2) V_H = (R_H I B)/t; V_H in V is transverse voltage; R_H in m³/C is Hall coefficient; I in A is current; B in T is magnetic flux density perpendicular to current; t in m is sample thickness along B. 3) Positive R_H suggests hole-like dominant carriers (p-type behavior or complex band effects in a metal).

Finished this topic? Mark it so your progress, study plan and readiness keep up.

Stuck on something here?