Applications of lasers
Practical uses of lasers in engineering: manufacturing (cutting, welding, drilling, surface treatment), measurements and metrology (interferometry, alignment, ranging), communication and sensing (optical discs, barcode scanners, LIDAR), and medicine and safety.
Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.
Why it matters
Engineers use lasers for precision tasks where ordinary light or mechanical tools are not accurate or fast enough. Examples include micrometer-accurate measurements on shop floors, high-speed cutting and welding of metals and polymers, long-range surveying (LIDAR), and medical procedures with minimal damage to surrounding tissue.
Key ideas
Recap (from “Lasers: principle and types”): stimulated emission produces a photon identical to the incident photon; population inversion (more atoms in an excited state than in a lower state) and an optical resonator (two-mirror cavity) are required to achieve laser action.
Beam quality and focusing (why lasers can deliver energy precisely)
- Beam divergence (θ) is the half-angle angular spread of the beam. For a circular diffraction-limited beam of diameter D at the exit aperture, the half-angle to the first minimum is approximately θ ≈ 1.22·λ/D (small-angle, θ in radians). Lower divergence means energy stays concentrated over long distances.
- Focusing by a lens concentrates the beam to a small spot. For a circular aperture lens of focal length f and clear aperture D, the radius to the first dark ring (Airy radius) in the focal plane is r ≈ 1.22·λ·f/D. Smaller wavelength λ, larger D, or shorter f give a smaller spot.
- Intensity (I) is power per unit area. High intensity at the focus enables rapid heating, melting, or vaporization in materials processing.
Photons and energy delivery
- A photon is a quantum of light with energy E = h·ν = h·c/λ. For cutting or surgery, both the total power and how strongly the material absorbs at the laser’s wavelength control heating.
- Absorption coefficient (α) describes how strongly a material absorbs light at a wavelength. Materials are chosen or surface-treated to increase absorption for efficient processing.
Continuous-wave vs pulsed lasers (matching application to source)
- A continuous-wave (CW) laser emits constant power over time; useful for steady heating (e.g., welding and cutting of sheets).
- A pulsed laser emits energy in short bursts. The pulse energy (E_p) and peak power (P_peak = E_p/τ_p) can be very high even if average power is moderate; this enables drilling, micromachining, shock peening, and minimally thermal damage when the pulse is shorter than the heat diffusion time.
- Q-switching and mode-locking are methods (see earlier topic) to obtain high-energy or ultrashort pulses. In applications, you choose pulse duration to control the heat-affected zone.
Key application domains
- Materials processing: cutting, drilling, welding, surface hardening, cladding, additive manufacturing. Lasers deliver controlled energy with minimal mechanical force, small kerf width, and high repeatability.
- Metrology and alignment: interferometric displacement measurement, straightness/level alignment lines, laser trackers, and calibration of machine tools.
- Ranging and imaging: LIDAR (Light Detection and Ranging) for distance and 3D mapping using time-of-flight or phase shift measurement.
- Information and consumer devices: optical data storage (CD/DVD/Blu-ray), barcode scanners, laser printers.
- Medicine: ophthalmic surgery (e.g., LASIK), dermatology (tattoo removal, hair removal), photocoagulation in retina, soft tissue cutting with minimal bleeding.
- Communication: laser diodes couple into optical fibers for long-distance, high-bandwidth links (see “Optical fibres”).
- Holography: recording and reconstruction of 3D images using interference; applications include data storage, microscopy, and metrology (surface profiling, vibration analysis).
Measurement principles commonly examined
- Interferometry with a laser (Michelson interferometer): coherent, monochromatic light produces stable fringes; mirror displacement causes fringe shifts. One fringe shift corresponds to a path change of one wavelength; a mirror movement of λ/2 changes the round-trip path by λ.
- Time-of-flight ranging: distance R = c·Δt/2 from transmitted pulse to received echo; factor 1/2 because light travels out and back.
- Laser Doppler (for velocity): frequency shift f_d relates to target velocity. In simple backscatter geometry at normal incidence, f_d ≈ 2·v/λ.
Safety and standards (engineering practice)
- Laser safety classes (IEC 60825-1): broadly, Class 1 (safe under normal use) to Class 4 (hazardous to eye/skin, fire risk). Engineering controls (enclosures, interlocks), administrative controls (training, signage), and personal protective equipment (appropriate optical density goggles at the laser wavelength) are mandatory in labs and factories.
Diagrams to draw in exams
- Laser machining setup: draw and label laser source, beam expander/collimator, mirrors, focusing lens, workpiece on translation stage; indicate focused spot and assist gas nozzle if mentioned.
- Michelson interferometer: laser, beam splitter at 45°, two mirrors (one movable), recombined beams at detector/screen; mark optical paths.
- Time-of-flight LIDAR block diagram: laser transmitter, scanner optics, target, receiver telescope, photodetector, timing/counter module, and processor.
Formulas
θ ≈ 1.22·λ/D— Far-field divergence (radians) of a diffraction-limited circular beam; λ: wavelength (m), D: beam diameter at aperture (m). Small-angle approximation.r ≈ 1.22·λ·f/D— Airy disk radius at the focal plane of a lens (m); f: focal length (m), D: lens clear aperture (m). Diffraction-limited focusing.d ≈ 2·r— Approximate focused spot diameter (m) for a circular aperture, first-dark-ring to first-dark-ring. Diffraction-limited condition.N_photons/s = P/E_photon— Photon flux; P: laser power (W), E_photon: energy per photon (J). Applies when monochromatic.L_c ≈ c/Δν— Coherence length; Δν: spectral linewidth (Hz). Approximate; exact prefactor depends on lineshape (e.g., Lorentzian: L_c = c/(π·Δν); Gaussian: L_c ≈ 0.44·c/Δν). For exams, quoting L_c ≈ c/Δν with stated assumption is acceptable; c: m/s.Δx = m·λ/2— Mirror displacement from m fringe shifts in a Michelson interferometer; Δx: displacement (m), m: number of fringes, λ: laser wavelength (m). Assumes normal incidence and equal-arm geometry.R = c·Δt/2— Time-of-flight range; R: distance to target (m), Δt: round-trip time (s), c: speed of light (m/s). Assumes propagation in air approximated as vacuum and negligible processing delays.f_d ≈ 2·v/λ— Laser Doppler frequency shift for backscatter at normal incidence; f_d: Hz, v: target speed along beam (m/s), λ: wavelength (m). Valid for v ≪ c and direct backscatter.v_scan ≈ η·P/E′— Steady-state laser cutting scan speed; v_scan: m/s, η: coupling efficiency (0–1), P: laser power incident (W), E′: required energy per unit length to cut (J/m). Empirical E′ depends on material and thickness.
Worked examples
- Power density and scan speed in laser cutting Given: A 200 W CW laser is focused to a circular spot of diameter 50 µm on a steel sheet. The process requires an effective energy per unit length E′ = 5.0×10³ J/m to achieve full cut-through. Assume coupling efficiency η = 0.20 (20% of laser power becomes useful cutting energy). Find (a) the intensity at the spot, and (b) the maximum scan speed to maintain the cut.
Steps:
- Spot area A for diameter d = 50 µm = 50×10⁻⁶ m. Radius r = d/2 = 25×10⁻⁶ m. Area
A = π·r².- A = π·(25×10⁻⁶ m)² = π·625×10⁻¹² m² = 1.9635×10⁻⁹ m² (rounded).
- Intensity
I = P/A.- I = 200 W / 1.9635×10⁻⁹ m² = 1.019×10¹¹ W/m².
- Answer (a): I ≈ 1.0×10¹¹ W/m².
- Available useful power
P_useful = η·P = 0.20×200 W = 40 W. - Scan speed
v_scan = P_useful/E′.- v_scan = 40 W / (5.0×10³ J/m) = 8.0×10⁻³ m/s.
- Convert: 8.0×10⁻³ m/s = 8.0 mm/s.
Final answers: (a) Intensity ≈ 1.0×10¹¹ W/m². (b) Maximum scan speed ≈ 8.0 mm/s. Both are reasonable for thin-sheet cutting with modest power and moderate coupling.
- Displacement measurement with a laser interferometer Given: In a Michelson interferometer illuminated by a 532 nm laser (green), a mirror is moved slowly and 250 bright fringes pass a reference point. Find the mirror displacement.
Steps:
- For each fringe shift, the optical path difference changes by one wavelength λ, but mirror movement Δx changes round-trip by 2·Δx. Thus
Δx = m·λ/2. - λ = 532 nm = 532×10⁻⁹ m; m = 250.
- Compute Δx: Δx = 250 × (532×10⁻⁹ m)/2 = 250 × 266×10⁻⁹ m = 66,500×10⁻⁹ m = 6.65×10⁻⁵ m.
Final answer: Mirror displacement = 66.5 µm (i.e., 6.65×10⁻⁵ m). The arithmetic checks out.
- LIDAR time-of-flight range Given: A pulsed laser LIDAR measures a round-trip time Δt = 3.20 µs for a reflection from a distant wall. Estimate the distance R (ignore air refractive index corrections and electronics delay).
Steps:
- Use
R = c·Δt/2. - c ≈ 3.00×10⁸ m/s; Δt = 3.20 µs = 3.20×10⁻⁶ s.
- Compute: R = (3.00×10⁸ m/s × 3.20×10⁻⁶ s)/2 = (960 m)/2 = 480 m.
Final answer: Distance to the wall ≈ 480 m.
Common mistakes
- Assuming intensity equals power without dividing by area; not converting spot diameter to area via πr².
- Claiming zero heat-affected zone with lasers; even ultrashort pulses can create some thermal or shock effects depending on material and pulse parameters.
- Ignoring coupling efficiency and reflectivity in cutting/welding calculations; overestimates achievable speeds.
- Confusing beam divergence formulas for near-field vs far-field; θ ≈ 1.22·λ/D applies to diffraction-limited, circular apertures only.
- Using optical fiber concepts (attenuation in dB/km, numerical aperture) as if they directly describe free-space laser beams; different models apply (see “Optical fibres”).
For your exam
- Derivations and standard results: Airy disk spot size r ≈ 1.22·λ·f/D; divergence θ ≈ 1.22·λ/D; interferometric displacement Δx = m·λ/2; time-of-flight range R = c·Δt/2; simple Doppler f_d ≈ 2·v/λ (state assumptions clearly).
- Numericals: power density at a focus; photon flux for a given laser; displacement from fringe counts; LIDAR distance from timing; scan speed from power and energy-per-length requirement.
- Diagrams: neatly labeled laser machining optical train; Michelson interferometer; LIDAR block diagram. Use straight rays, 90°/45° optics as appropriate, show beam splitter orientation, and label all distances if asked.
- What full-marks answers include: clear definitions in bold/underlined words, correct formulas with units, assumptions stated (e.g., diffraction-limited, small angles, negligible losses), clean step-by-step calculations with unit conversions, and neat annotated diagrams when relevant.
Quick check
- A He–Ne laser (λ ≈ 632.8 nm) is focused by a lens (f = 100 mm, D = 25 mm). Estimate the diffraction-limited spot diameter at focus.
- A time-of-flight LIDAR measures Δt = 0.500 µs. What is the distance to the target?
- In a Michelson interferometer with λ = 633 nm, 40 fringes pass. How far did the mirror move?
Answers: (1) r ≈ 1.22·λ·f/D = 1.22×(632.8×10⁻⁹ m)×0.100 m/0.025 m ≈ 3.09×10⁻⁶ m, so d ≈ 6.18 µm. (2) R = c·Δt/2 ≈ (3.00×10⁸ m/s×0.500×10⁻⁶ s)/2 ≈ 75.0 m. (3) Δx = m·λ/2 = 40×633×10⁻⁹/2 ≈ 12.66 µm.
Finished this topic? Mark it so your progress, study plan and readiness keep up.
Stuck on something here?