Network theorems: superposition and Thevenin
Network theorems: superposition and Thevenin — statements, assumptions, procedures, formulas, and worked DC/AC examples for first-year exams.
Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.
Why it matters
Network theorems let you break complicated circuits into simpler parts so you can predict voltages, currents, and power without solving large simultaneous equations every time. Superposition explains how multiple sources combine in a linear circuit, and Thevenin’s theorem turns any linear two‑terminal network into a simple source with a single series resistance (or impedance) as seen by a load. These tools are used in sensor interfacing, biasing of amplifiers, power system fault approximations, and quickly checking design changes.
Key ideas
- Bilateral network: A network whose behavior is the same in both directions of current flow (e.g., resistors). Note: Superposition and Thevenin do not require bilateral elements; linearity is the key assumption.
- Independent source: A voltage or current source whose value is fixed by the source itself (not dependent on any circuit variable).
- Dependent source: A source whose value is a scaled version of some circuit voltage or current (controlled source); it is part of many linear models and is NOT turned off when “deactivating” independent sources.
- Open-circuit: Terminals not connected to any load; current is zero through the open branch.
- Short-circuit: Terminals directly connected by an ideal conductor (zero resistance); voltage between them is zero.
- Equivalent circuit: A simpler circuit that behaves the same as the original at specific terminals, for all external loads and for the specified operating conditions (DC or a given sinusoidal frequency with phasors).
Exact statements and assumptions (use these in exams):
- Superposition Theorem — Statement “In any linear circuit with multiple independent sources, the response (voltage across or current through any element) is the algebraic sum of the responses produced by each independent source acting alone, with all other independent voltage sources replaced by their internal resistances (ideal sources shorted) and all other independent current sources replaced by their internal resistances (ideal sources opened). Dependent sources, if present, remain as they are.”
Assumptions and applicability:
- The circuit must be linear (elements obey linear relationships; for AC, use linear impedances and phasors at a single frequency).
- Works for DC and single-frequency AC. For multi-frequency AC, apply superposition separately at each frequency.
- Power does not superpose directly (because power is quadratic). Voltages and currents do.
Procedure (exam-answer steps):
- Identify all independent sources.
- Select one source to keep active; deactivate all other independent voltage sources by replacing them with shorts, and all other independent current sources by replacing them with opens. Keep all dependent sources as they are.
- Solve the simpler circuit for the desired voltage or current (label it with a subscript for that source, e.g., V1-only).
- Repeat for each independent source.
- Algebraically sum the individual voltages or currents (include sign and, in AC, phasor angles) to get the total response.
Diagram to draw (describe):
- Draw the full given circuit with all sources and elements labeled (polarities, current directions). Then, for each source case, sketch the modified circuit (with other independent sources deactivated) and clearly indicate opens/shorts. Finally, show the vector/arithmetical sum of responses at the element of interest.
Derivation idea (brief):
- From linearity: If f(·) is a linear mapping from sources to responses, then for sources S = S1 + S2 + …, response R = f(S) = f(S1) + f(S2) + … . This is the mathematical justification.
- Thevenin’s Theorem — Statement “Any linear two-terminal network of sources and impedances, as seen from two terminals, is electrically equivalent to a single ideal voltage source Vth in series with an equivalent resistance Rth (for DC) or equivalent impedance Zth (for AC at a specified frequency). This equivalent produces the same terminal voltage and current for any external load connected to the two terminals.”
Assumptions and applicability:
- The internal network must be linear. Works for DC and single-frequency AC (use complex impedances in AC).
- Dependent sources are allowed; special care is needed when finding Rth/Zth.
How to find Thevenin equivalent (exam procedure): Method A (Open-circuit voltage and equivalent resistance/impedance):
- Identify the two terminals (where the load connects). Remove the load (open circuit it).
- Compute the open-circuit voltage across the terminals. This is Vth.
- Find Rth (or Zth in AC):
- Deactivate all independent sources: replace ideal voltage sources with shorts and ideal current sources with opens. Keep dependent sources active.
- Compute the equivalent resistance/impedance seen looking into the terminals (you may need series/parallel combinations or a test source if dependent sources are present).
Method B (Using short-circuit current):
- Compute the open-circuit voltage Vth as above.
- Short the terminals and compute the short-circuit current Isc.
- Then Rth = Vth / Isc (for DC). In AC, use Zth = Vth / Isc (phasor division). This is often faster when meshes are simple.
If dependent sources are present and you cannot directly zero all sources to measure Rth:
- Apply a known test source (voltage Vtest or current Itest) at the terminals with independent sources deactivated; compute the resulting Itest or Vtest; then Rth = Vtest / Itest (or Zth in AC).
Diagram to draw (describe):
- Original two-terminal network: show terminals a–b (or A–B), label all sources and elements. Next, draw the open-circuit condition and indicate the measured Vth across a–b (with polarity). Then draw the deactivated-source condition and show how to compute Rth looking into a–b (series/parallel reductions or a test source). Optionally, show the short-circuit with Isc arrow. Finally, draw the Thevenin equivalent: an ideal source Vth in series with Rth (or Zth), connected to the load RL.
Short notes to remember:
- Thevenin ↔ Norton: You can convert between them (Norton current In = Vth/Rth; Norton resistance = Rth). Mention only if asked; full Norton method is another theorem.
- In AC, always use phasors: V, I, and Z are complex; keep angles.
- Superposition and Thevenin both fail for nonlinear elements (e.g., diodes) unless operating in a linearized small-signal region.
Formulas
Vth = Voc
- Vth: Thevenin voltage (V), Voc: open-circuit terminal voltage (V). Applies to linear two-terminal networks (DC or single-frequency AC phasors).
Rth = Vth / Isc
- Rth: Thevenin resistance (Ω), Vth: Thevenin voltage (V), Isc: short-circuit current (A). For DC. In AC, use the phasor relation Zth = Vth / Isc.
Zth = Vth / Isc
- Zth: Thevenin impedance (Ω), Vth and Isc are phasors at the same frequency. Single-frequency AC.
Rth (with sources deactivated) = equivalent resistance seen into the terminals
- Replace independent voltage sources by shorts, independent current sources by opens; keep dependent sources. Result in Ω for DC. For AC at a single frequency, perform the same using complex impedances to obtain Zth (in Ω).
Superposition: total response = sum of individual responses
- For a chosen element:
V_total = Σ V_k,I_total = Σ I_k, where k indexes each independent source acting alone. Works for linear circuits; voltages/currents add algebraically (phasors in AC). Do not add powers directly.
ZC = 1 / (j·ω·C) = −j / (ω·C)
- ZC: capacitor impedance (Ω), j: √(−1), ω: angular frequency in rad/s (ω = 2πf), C: capacitance (F). Single-frequency AC.
ZL = j·ω·L
- ZL: inductor impedance (Ω), L: inductance (H). Single-frequency AC.
Voltage division (phasors in AC) : Vout = Vin × Z2 / (Z1 + Z2)
- Vout across Z2 in series with Z1. Applies to linear, series impedances.
Parallel combination: Z = (Z1·Z2) / (Z1 + Z2)
- Equivalent impedance of two parallel impedances Z1 and Z2. DC resistors or AC impedances.
Worked examples
Example 1 (Superposition, DC): Given: Ideal voltage source V1 = 12 V from ground to node L (positive at L). Resistor R1 = 3 Ω from node L to node N. Resistor R2 = 6 Ω from node N to ground. Ideal current source I1 = 2 A from ground to node N (arrow upward into N). Find: (a) Voltage at node N, (b) Current through R2, using superposition.
- With only V1 active (I1 deactivated → open circuit):
- Circuit reduces to V1 (node L at 12 V), R1 in series to node N, R2 from node N to ground.
- Use voltage division: Formula: V_N1 = Vin × R2/(R1+R2).
- Numbers: V_N1 = 12 V × 6 Ω/(3 Ω + 6 Ω) = 12 × 6/9 = 8 V.
- Current through R2 due to V1: I_R2_1 = V_N1/R2 = 8 V / 6 Ω = 1.3333 A (downward to ground).
- With only I1 active (V1 deactivated → short circuit):
- Node L becomes ground; R1 connects node N to ground (3 Ω), R2 connects node N to ground (6 Ω). They are in parallel.
- Equivalent resistance seen by the current source: Req = (R1·R2)/(R1+R2) = (3×6)/(3+6) = 18/9 = 2 Ω.
- Node voltage due to current source: V_N2 = I1 × Req = 2 A × 2 Ω = 4 V.
- Current through R2 due to I1: I_R2_2 = V_N2/R2 = 4 V / 6 Ω = 0.6667 A (downward).
- Total by superposition:
- Node voltage: V_N = V_N1 + V_N2 = 8 V + 4 V = 12 V.
- R2 current: I_R2 = I_R2_1 + I_R2_2 = 1.3333 A + 0.6667 A = 2.0000 A.
Answer: (a) V_N = 12 V. (b) I_R2 = 2.00 A (downward through R2).
Check (direct KCL with both sources): At node N, (V−12)/3 + V/6 = 2 ⇒ 3V = 36 ⇒ V = 12 V; I_R2 = 12/6 = 2 A. Matches.
Example 2 (Thevenin equivalent, DC, then load current): Given two-terminal network at terminals a (node B) and b (ground): Ideal voltage source V = 24 V from ground to node A (positive at A). Resistor R1 = 6 Ω from A to B. Resistor R2 = 12 Ω from B to ground. Find the Thevenin equivalent seen at a–b, then find the load current if RL = 8 Ω is connected between a and b.
- Open-circuit voltage Vth = Voc:
- With output open, R1 and R2 form a divider from 24 V to ground. Formula: V_B = 24 × R2/(R1 + R2).
- Numbers: Vth = 24 × 12/(6 + 12) = 24 × 12/18 = 24 × 2/3 = 16 V.
- Thevenin resistance Rth (deactivate independent sources):
- Deactivate V (ideal voltage source → short). Then R1 and R2 both connect B to ground in parallel.
- Rth = R1 || R2 = (6×12)/(6+12) = 72/18 = 4 Ω.
Thevenin equivalent: Vth = 16 V in series with Rth = 4 Ω at terminals a–b.
With load RL = 8 Ω connected: Load current by Thevenin: Formula: IL = Vth / (Rth + RL).
- Numbers: IL = 16 V / (4 Ω + 8 Ω) = 16/12 = 1.3333 A.
Answer: Thevenin equivalent is a 16 V source in series with 4 Ω. Load current IL = 1.333 A.
Check (original circuit): R2 || RL = 12 || 8 = (96)/(20) = 4.8 Ω; V at B = 24 × 4.8/(6 + 4.8) = 24 × 4.8/10.8 = 10.6667 V; IL = 10.6667/8 = 1.3333 A. Matches.
Example 3 (Thevenin equivalent, single-frequency AC phasors): Given: Frequency f = 50 Hz. Ideal sinusoidal source Vs = 10∠0° V (rms). Series resistor R1 = 5 Ω from source to node N. Capacitor C chosen such that XC = 10 Ω at 50 Hz; so C = 1/(ω·XC) with ω = 2πf. Thus C ≈ 1/(2π×50×10) ≈ 318 μF. Capacitor from node N to ground. Find Thevenin equivalent seen at node N–ground; then, with RL = 4 Ω connected at N–ground, find load current (phasor).
- Compute ZC at 50 Hz:
- ZC = −j·XC = −j10 Ω (since XC = 10 Ω by design).
- Open-circuit voltage Vth (voltage division with impedances):
- Vth = Vs × ZC / (R1 + ZC) = 10∠0° × (−j10) / (5 − j10).
- Compute complex ratio: (−j10)/(5 − j10) = (100 − j50)/125 = 0.8 − j0.4.
- So Vth = 10 × (0.8 − j0.4) = 8 − j4 V. Magnitude |Vth| = √(8² + (−4)²) = √(64+16) ≈ 8.944 V; angle ≈ −26.565°.
- Thevenin impedance Zth (deactivate independent source: Vs → short):
- Looking into node N, R1 is to ground and C is to ground, so Zth = R1 || ZC = (5 × (−j10)) / (5 − j10) = 4 − j2 Ω. Magnitude ≈ √(4² + (−2)²) = √20 ≈ 4.472 Ω; angle ≈ −26.565°.
- With RL = 4 Ω connected: Load current IL = Vth / (Zth + RL) = (8 − j4) / (8 − j2).
- Compute: (8 − j4)/(8 − j2) = [(8 − j4)(8 + j2)] / [(8 − j2)(8 + j2)] = (72 − j16)/68 ≈ 1.0588 − j0.2353 A.
- Magnitude |IL| ≈ √(1.0588² + (−0.2353)²) ≈ 1.085 A; angle ≈ −12.6°.
Answer: Vth = 8 − j4 V (≈8.94∠−26.6° V). Zth = 4 − j2 Ω (≈4.47∠−26.6° Ω). With RL = 4 Ω, IL = 1.059 − j0.235 A (≈1.085∠−12.6° A).
Diagram to sketch for AC case (describe):
- Original source Vs, series R1 to node N, capacitor from N to ground, terminals at N–ground. Next, the Thevenin equivalent: a single source Vth in series with impedance Zth feeding RL.
Common mistakes
- Adding powers from each superposition case. Only voltages and currents add. Compute power after summing the final voltage/current.
- Forgetting to open an independent current source or to short an independent voltage source when deactivating.
- Losing sign conventions and current directions; not marking reference polarities before starting.
- In AC, mixing magnitudes and phasors: adding magnitudes instead of complex numbers; forgetting angles.
- Assuming Rth is just the parallel of resistors without first deactivating sources; or forgetting that with a shorted ideal voltage source, some resistors become directly in parallel with others.
- For Thevenin with dependent sources only: trying to “turn off” and getting meaningless infinite/zero values; the correct method is to use a test source to find Zth.
- Units mistakes (e.g., using kΩ as Ω). Always write SI units.
For your exam
- Short notes: “When to use superposition,” “Test source method for Rth with dependent sources,” “Relation between Thevenin and Norton.” Keep it crisp, with 2–3 points.
- Derivations/proofs outline: Show linearity leading to superposition (homogeneity and additivity). For Thevenin, outline equivalence by matching Voc and Isc and hence matching all load behaviors.
- Procedures/algorithms: Numbered steps for superposition and for finding Vth and Rth (both deactivation and Isc methods). Marks come from correct steps even if arithmetic slips.
- Numericals (DC and AC): Carry units through each step, state formulas before substituting, show intermediate values, and box/bold the final answer with units. For AC, show phasor arithmetic or rectangular-to-polar conversions.
- Diagrams: Draw clean, labeled circuits; indicate opens/shorts when deactivating sources; mark terminal polarities and current directions.
Exam tip: If time is short, for Thevenin prefer Rth = Vth/Isc when meshes are simple; otherwise use deactivation or a test source as appropriate.
Quick check
- In superposition, how do you deactivate an ideal current source? How about an ideal voltage source?
- What is Rth if Vth = 15 V and Isc = 3 A? State units.
- For AC at 60 Hz, what is the impedance of a 100 μF capacitor? Give in rectangular form.
Answers: (1) Replace an ideal current source with an open circuit; replace an ideal voltage source with a short circuit. (2) Rth = 15/3 = 5 Ω. (3) ω = 2π×60 ≈ 377 rad/s; XC = 1/(ωC) ≈ 1/(377×100×10⁻⁶) ≈ 26.5 Ω; ZC = −j26.5 Ω.
Finished this topic? Mark it so your progress, study plan and readiness keep up.
Stuck on something here?