First Year Engineering is coming soon

We're still writing and reviewing the notes for every subject, and we'll open it when every subject is ready. Meanwhile you can practise aptitude, ask Aria about any subject, or see the branches that are ready.

AC fundamentals: RMS and average values, phasors

AC fundamentals: measuring RMS and average values of periodic waveforms and using phasors to represent and add sinusoids of the same frequency.

Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.

Why it matters

RMS and average values tell you what a time-varying (AC) voltage or current actually “does” as heat and charge flow, so you can size wires, fuses, and equipment correctly. Phasors let you replace time-varying sinusoids by steady complex numbers, making addition, subtraction, and solving AC circuits (later topics) simple and systematic.

Key ideas

  • Instantaneous value: The value of a time-varying quantity at a specific instant t, written v(t) or i(t), in volts (V) or amperes (A).
  • Average (mean) value over an interval: The average of x(t) on interval [t1, t2] is x̄ = (1/(t2 − t1)) ∫_{t1}^{t2} x(t) dt. For a symmetric AC sine wave over a full cycle, the average is zero; in practice we often quote average over a half-cycle for rectified waveforms.
  • Average (mean) value of a periodic waveform: For one full period, x_avg,full = (1/T) ∫{0}^{T} x(t) dt. For waveforms that are symmetric about zero (like pure sine), this equals 0. For rectified waveforms, we commonly use the half-cycle mean x_avg,half = (2/T) ∫{0}^{T/2} x(t) dt.
  • RMS (root-mean-square) value: The effective value of a periodic current or voltage defined as the square root of the mean of the square over one period: X_rms = sqrt( (1/T) ∫_{0}^{T} [x(t)]^2 dt ). RMS produces the same heating (power in a resistor) as a DC quantity of the same magnitude.
  • Sine wave definitions: A sinusoidal voltage is v(t) = V_m sin(ωt + φ) or v(t) = V_m cos(ωt + φ), where V_m is peak (maximum) value, φ is phase angle. For a pure sine, v_rms = V_m/√2 and the average over a half-cycle is V_avg,half = (2/π) V_m.
  • Form factor: For any periodic waveform, Form factor = X_rms / X_avg,half. For a sine wave, Form factor = (V_m/√2) / (2V_m/π) = π/(2√2) ≈ 1.11.
  • Peak (crest) factor: Crest factor = X_peak / X_rms. For a sine wave, Crest factor = V_m / (V_m/√2) = √2 ≈ 1.414.
  • Phasor: A phasor is a complex-number representation of a sinusoid of a single fixed frequency, expressed as a rotating vector with constant magnitude at angular speed ω. We conventionally write a time-domain quantity as x(t) = X_m cos(ωt + φ). The corresponding phasor is X = X_rms ∠ φ (polar) or X = X_rms (cos φ + j sin φ) (rectangular), where j = √−1.
  • Reference and phase angle: In a phasor diagram, choose a reference (often the supply voltage). A phasor at angle +φ leads the reference by φ; at −φ lags by φ. Angle is measured counterclockwise from the positive real axis.
  • Addition of sinusoids using phasors: Sinusoids of the same frequency can be added by adding their phasors as complex numbers: X_total = X1 + X2 + … . The time-domain resultant is x_total(t) = √2·|X_total| cos(ωt + ∠X_total) if phasors are RMS-based. (If using peak-based phasors, omit √2.)
  • j-operator and rectangular/polar forms: A phasor X can be written X = a + jb (rectangular) or X = |X| ∠ θ (polar), with conversions: |X| = √(a^2 + b^2), θ = atan2(b, a), a = |X| cos θ, b = |X| sin θ.
  • Impedance phasors for basic elements (preview for later topics): For sinusoidal steady state at angular frequency ω: resistor Z_R = R ∠ 0° (Ω), inductor Z_L = jωL (Ω) = ωL ∠ +90°, capacitor Z_C = 1/(jωC) = −j/(ωC) (Ω) = (1/ωC) ∠ −90°. In a resistor, v and i are in phase; in an inductor, i lags v by 90°; in a capacitor, i leads v by 90°.

Common exam derivations and diagrams to draw

  • Derivation: RMS of a sine wave
    1. v(t) = V_m sin(ωt). Over one period T = 2π/ω.
    2. v_rms = sqrt( (1/T) ∫{0}^{T} v^2(t) dt ) = sqrt( (1/T) ∫{0}^{T} V_m^2 sin^2(ωt) dt ).
    3. Use identity sin^2 x = (1 − cos 2x)/2 and integrate over a full period to get average of sin^2 as 1/2.
    4. v_rms = V_m / √2.
  • Derivation: Average (half-wave) of a sine wave
    1. v(t) = V_m sin(ωt) for 0 to π (half-cycle in angle variable).
    2. V_avg,half = (1/π) ∫_{0}^{π} V_m sin θ dθ (use θ = ωt).
    3. Integrate to obtain (V_m/π)[−cos θ]_0^π = (V_m/π)(2) = 2V_m/π.
  • Diagram: Sine wave and labels
    • Draw a horizontal time axis t and vertical voltage axis v.
    • Plot one cycle of a sine wave starting at zero and peaking at V_m at ωt = π/2, crossing zero at π, negative peak at 3π/2, and back to zero at 2π.
    • Label peak value V_m, period T, and mark RMS level at V_m/√2 (use a dashed horizontal line).
  • Diagram: Phasor diagram
    • Draw horizontal real axis (Re) to the right and vertical imaginary axis (Im) upward.
    • Draw a reference phasor V along the real axis.
    • Draw another phasor I at angle −φ to indicate lag (or +φ for lead). Label magnitudes |V|, |I| and angle φ.
  • Diagram: Addition of two phasors
    • Draw X1 and X2 from origin with their angles. Construct the parallelogram; the diagonal from origin is the resultant X_total. Label the angles and magnitudes.

Assumptions behind phasors

  • All phasors in a problem refer to the same single frequency (steady-state sinusoidal). If frequencies differ, phasor addition is not valid; signals must be handled separately in time domain or via Fourier methods (beyond this topic).
  • RMS-based phasors are standard in electrical engineering for voltages and currents; be consistent. If you choose peak-based phasors, state it clearly and do not mix with RMS.

Formulas

f = 1/T

  • f: frequency (Hz), T: period (s); for any periodic signal.

ω = 2·π·f

  • ω: angular frequency (rad/s), f: Hz; sinusoidal steady state.

x_avg,full = (1/T) · ∫₀ᵀ x(t) dt

  • x_avg,full: average over a full cycle (same unit as x), T: period (s); general periodic function.

x_avg,half = (2/T) · ∫₀ᵀ⁄₂ x(t) dt

  • x_avg,half: average over a half-cycle (same unit as x); typically used for rectified waveforms.

x_rms = √[ (1/T) · ∫₀ᵀ (x(t))² dt ]

  • x_rms: RMS value (same unit as x); general periodic function.

v(t) = V_m · sin(ωt + φ)

  • v(t): instantaneous voltage (V), V_m: peak voltage (V), φ: phase angle (rad), ω: rad/s; sinusoid.

V_rms = V_m/√2

  • V_rms: RMS voltage (V), V_m: peak voltage (V); pure sine wave.

V_avg,half = (2/π) · V_m

  • V_avg,half: average of rectified sine over half-cycle (V), V_m: peak (V); sine wave magnitude over half cycle. For a full-wave rectified sine over one full period, V_avg,full-rect = (2/π) · V_m and V_rms = V_m/√2.

Form factor = X_rms / X_avg,half

  • Dimensionless; any periodic waveform (half-cycle average must be nonzero).

Crest factor = X_peak / X_rms

  • Dimensionless; any periodic waveform.

X = X_rms ∠ φ = X_rms (cos φ + j sin φ)

  • X: phasor (complex), X_rms: RMS magnitude (unit of x), φ: phase (rad or °), j: √−1; sinusoidal steady state phasor representation.

|X| = √(a² + b²), θ = atan2(b, a)

  • For X = a + jb (rectangular), magnitude |X| and angle θ in radians; conversion rectangular to polar.

a = |X| cos θ, b = |X| sin θ

  • For X = a + jb; conversion polar to rectangular.

X_total = X₁ + X₂ + … + X_n

  • Vector (complex) sum of phasors at the same frequency.

Z_R = R

  • Impedance of resistor R (Ω), angle 0°; sinusoidal steady state.

Z_L = j·ω·L

  • Impedance of inductor L (H), ω rad/s; angle +90°.

Z_C = 1/(j·ω·C) = −j/(ω·C)

  • Impedance of capacitor C (F), ω rad/s; angle −90°.

v(t) = √2 · Re{ V · e^{jωt} }

  • v(t): instantaneous voltage (V), V: RMS phasor (complex V), Re{}: real part; links phasor to time-domain cosine reference.

Worked examples

Example 1: RMS and average of a triangular waveform Given: A symmetrical triangular voltage v(t) of peak V_m = 12 V over period T, rising linearly from 0 to +12 V in T/4, then to −12 V in next T/2, and back to 0 in last T/4 (zero average over full cycle). Find (a) V_rms and (b) the average over half-cycle of its magnitude (rectified), V_avg,half.

  1. Identify piecewise linear symmetry: For a symmetric triangular wave with peak ±V_m, the RMS over a full cycle is V_rms = V_m/√3.
  2. Compute V_rms by integral to show steps:
    • Over 0 to T/2, v(t) ramps from 0 to +12 V then to 0; over T/2 to T it mirrors to negative and back. Square removes sign. Use known result or integrate line segments. Using known standard result for a symmetrical triangle:
    • V_rms = V_m/√3 = 12/√3 V = 6.928 V (approx).
  3. Average of rectified triangular wave over half-cycle: For a symmetric triangle, V_avg,half = V_m/2.
    • Thus V_avg,half = 12/2 = 6.0 V. Answer: (a) V_rms = 6.93 V (rounded to 2 d.p.) (b) V_avg,half = 6.00 V.

Example 2: RMS and average of a half-wave rectified sine current Given: i(t) = I_m sin(ωt) for 0 ≤ ωt ≤ π, and i(t) = 0 for π < ωt < 2π (half-wave rectified), with I_m = 5 A. Find (a) I_avg over full period, (b) I_rms over full period.

  1. Average over full period (nonzero only for half cycle):
    • I_avg = (1/2π) ∫₀^π I_m sin θ dθ = (I_m/(2π)) [−cos θ]_0^π = (I_m/(2π)) (2) = I_m/π.
    • Substitute I_m = 5 A: I_avg = 5/π A = 1.5915 A ≈ 1.592 A.
  2. RMS over full period:
    • I_rms = √[ (1/2π) ∫₀^π (I_m sin θ)² dθ ] = √[ (I_m²/(2π)) ∫₀^π sin² θ dθ ].
    • ∫₀^π sin² θ dθ = π/2. So I_rms = √[ (I_m²/(2π)) · (π/2) ] = I_m/2.
    • Substitute: I_rms = 5/2 A = 2.5 A. Answer: (a) I_avg = 1.592 A (approx) (b) I_rms = 2.50 A (exact).

Example 3: Phasor addition of two sinusoidal voltages Given: v1(t) = 120√2 cos(ωt + 20°) V and v2(t) = 80√2 cos(ωt − 40°) V. Find the resultant voltage v(t) in the form V_RMS ∠ φ and as a cosine in the time domain.

  1. Convert to RMS phasors (divide peaks by √2):
    • V1 = 120 ∠ 20° V, V2 = 80 ∠ (−40°) V.
  2. Convert to rectangular to add:
    • V1x = 120 cos 20° = 120 × 0.9396926 = 112.763 V; V1y = 120 sin 20° = 120 × 0.3420201 = 41.042 V.
    • V2x = 80 cos(−40°) = 80 × 0.7660444 = 61.2836 V; V2y = 80 sin(−40°) = 80 × (−0.6427876) = −51.4230 V.
  3. Sum components:
    • Vx = 112.763 + 61.2836 = 174.0466 V.
    • Vy = 41.042 + (−51.4230) = −10.3810 V.
  4. Convert to polar:
    • |V| = √(174.0466² + (−10.3810)²) ≈ √(30292.22 + 107.76) = √(30399.98) ≈ 174.3 V.
    • φ = atan2(Vy, Vx) = atan2(−10.3810, 174.0466) ≈ −3.42°.
  5. Write resultant phasor and time-domain voltage:
    • V = 174.3 ∠ (−3.42°) V (RMS).
    • v(t) = 174.3√2 cos(ωt − 3.42°) V = 246.5 cos(ωt − 3.42°) V. Answer: Resultant V ≈ 174.3 ∠ (−3.42°) V RMS; time-domain v(t) ≈ 246.5 cos(ωt − 3.42°) V.

Check of numeric steps (brief): cos 20° ≈ 0.93969, sin 20° ≈ 0.34202, cos 40° ≈ 0.76604, sin 40° ≈ 0.64279. Component sums and magnitude/angle recomputed above; final rounding to 0.1 V and 0.01°.

Example 4: Converting between time-domain and phasor, then adding currents in a branch Given currents: i1(t) = 10√2 cos(ωt) A and i2(t) = 6√2 cos(ωt − 90°) A flow into a node. Find total current as a phasor and as i(t).

  1. RMS phasors: I1 = 10 ∠ 0°, I2 = 6 ∠ (−90°) = 0 − j6.
  2. Rectangular form: I1 = 10 + j0, I2 = 0 − j6.
  3. Sum: I = 10 − j6. Magnitude |I| = √(10² + (−6)²) = √(100 + 36) = √136 = 11.6619 A.
  4. Angle φ = atan2(−6, 10) = −30.964° ≈ −30.96°.
  5. Phasor: I = 11.66 ∠ (−30.96°) A (RMS). Time-domain: i(t) = 11.66√2 cos(ωt − 30.96°) A = 16.49 cos(ωt − 30.96°) A. Answer: I ≈ 11.66 ∠ (−30.96°) A RMS; i(t) ≈ 16.49 cos(ωt − 30.96°) A.

Common mistakes

  • Using full-cycle average instead of half-cycle average when a question asks “average value” for a rectified waveform. State clearly whether you are giving full-cycle average (often zero) or half-cycle/rectified average.
  • Forgetting that RMS uses square–mean–square root. Averaging the raw values or taking mean of absolute values is not RMS.
  • Adding time-domain sinusoids directly with different phases (e.g., 10 cos ωt + 10 cos(ωt + 60°) = 20 cos ωt). This is wrong; use phasor or trigonometric identities.
  • Using degrees inside sin(), cos() of calculators set to radians (or vice versa). Set the correct mode and be consistent.
  • Writing phasor magnitudes as peak while impedances assume RMS, leading to wrong currents and powers.
  • Losing sign of angle: “lagging” means negative angle for current if voltage is reference; “leading” means positive.
  • For integrals: forgetting that average of sin² over a full cycle is 1/2; average of sin over a full cycle is zero.

For your exam

  • Derivations: Derive RMS of a sine wave; derive average of a half-wave rectified sine; show form factor for a sine is 1.11. Full marks: start with definitions, correct integrals over one period or half-period, correct identities, boundary values, and clean final expressions.
  • Numericals: Compute RMS and average for given waveforms (square, triangular, sawtooth, half-/full-wave rectified). Add two or more sinusoids of the same frequency with given amplitudes and phases. Full marks: list given data with units, show formula before substitution, carry units, result rounded with correct significant figures.
  • Phasor diagrams: Draw phasor of two voltages/currents showing lead/lag; parallelogram law for resultant. Full marks: axes labeled Re and Im, angles labeled with direction, magnitudes indicated, reference clearly stated.
  • Conceptual: Explain why phasors cannot add signals of different frequencies; distinguish RMS vs average; meaning of lead/lag. Full marks: clear, concise statements with one illustrative sentence.

Quick check

  1. What is the RMS value of a 230 V (RMS) household supply in terms of its peak value?
  2. State the average over a half-cycle of v(t) = V_m sin(ωt).
  3. Two RMS phasors: 20 ∠ 30° V and 15 ∠ (−60°) V. Which one leads the other, and by how many degrees?

Answers: 1) Peak V_m = √2 × 230 ≈ 325 V; RMS is already 230 V. 2) (2/π) V_m. 3) 20 ∠ 30° leads 15 ∠ (−60°) by 90°.

Finished this topic? Mark it so your progress, study plan and readiness keep up.

Stuck on something here?