Work and energy methods
Work–energy principle, potential energy (gravity, springs), conservative vs non-conservative work, power, and energy methods for particles and rigid bodies (including rotation and rolling).
Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.
Why it matters
Work–energy methods turn force–motion problems into bookkeeping of energy: what you lose from potential or input as work becomes kinetic or heat. They are fast for variable forces, rolling bodies, pulleys with inertia, and spring-contact events where F=ma is awkward.
Key ideas
- Infinitesimal work: dW = F·ds (vector dot product). Along general curvilinear motion, only the tangential component contributes instantaneously.
- Kinetic energy (T): For a particle of mass m moving with speed v, T = 1/2·m·v². For a rigid body, T = 1/2·m·v_G² + 1/2·I_G·ω², where v_G is the speed of the center of mass G, I_G is mass moment of inertia about G, and ω is angular speed. Special case: pure rotation about a fixed axis through O gives T = 1/2·I_O·ω².
- Work–energy theorem (particle): The change in kinetic energy equals the total work of all forces: ΣW = ΔT. Exact statement: For a particle moving from position 1 to 2 under resultant force F, ∫₁² F·ds = 1/2·m·v₂² − 1/2·m·v₁². Assumptions: Newtonian mechanics, inertial frame, rigid particle, forces well-defined along the path.
- Work–energy (rigid body): For a rigid body, the work of all external forces (including couples) equals the change in total kinetic energy: ΣW_ext = ΔT. Internal forces of an ideal rigid body do no net work (pairs are equal and opposite with equal virtual displacements).
- Power: The rate of doing work. For a particle or a point on a rigid body, P = F·v (instantaneous). For a couple/torque M causing angular speed ω, P = M·ω. Average power over time Δt is W/Δt.
- Potential energy (V): For conservative forces, we can define a scalar V such that F = −∇V and the work done depends only on end states. Near Earth’s surface, gravitational V_g = m·g·h (h measured upward from a chosen datum). For a linear spring obeying Hooke’s law F_s = kx (x measured from natural length), spring energy V_s = 1/2·k·x². Datum choices shift V by a constant but do not affect physics.
- Conservative vs non-conservative forces:
- Conservative forces (e.g., gravity, ideal spring): path-independent work, admit a potential. In a closed loop, net work is zero.
- Non-conservative forces (e.g., kinetic friction, viscous drag): path-dependent, dissipate mechanical energy, cannot be captured by a single-valued potential.
- Mechanical energy and conservation: Define E = T + V for systems with conservative forces. Then T₁ + V₁ + W_nc = T₂ + V₂, where W_nc is work by non-conservative forces or external agents. If W_nc = 0 (isolated, conservative), then T + V is constant (mechanical energy conserved).
- Work of common forces:
- Weight: W_g = m·g·(h₁ − h₂) when moving between elevations h₁ and h₂ (positive if descending).
- Spring: W_s from x₁ to x₂ is −1/2·k·(x₂² − x₁²). The negative sign reflects the restoring nature of the spring.
- Constant couple/torque M through angle θ: W = M·θ (positive if torque and rotation have the same sense).
- Kinetic friction: W_f = −μ_k·N·s along the direction of relative motion over sliding distance s (always dissipative). Static friction can do positive, negative, or zero work depending on relative motion of the point of contact; for pure rolling without slip on a stationary surface, the instantaneous contact point is at rest, so ideal static friction does zero work.
- Rolling without slipping: The kinematic constraint is v_G = R·ω for a body of radius R. Energy method treats both translation and rotation. For ideal rolling on a stationary rigid surface without rolling resistance, static friction does no work and mechanical energy is conserved if other forces are conservative.
- Equivalent mass concept (useful heuristic): For a rolling rigid body on an incline without slipping, the acceleration is reduced compared to a smooth block because some potential goes into rotational KE. The rotational part can be seen as adding an "effective inertia" term proportional to I_G/R² in energy balances.
- Variable forces and F–x curves: In 1D motion along x with force F(x), the work from x₁ to x₂ is the area under F–x: W = ∫ₓ₁^ₓ₂ F(x) dx.
- Choosing the system and what does work: In energy methods, pick the system (single particle, rigid body, or a set connected by an inextensible rope) so that constraint forces either do no work or are internal. For ideal pulleys and massless ropes without slip, rope tension does work on masses but internal to a multi-body system it may cancel; however, if the pulley has inertia, the rope does work on the pulley too (rotational KE term appears).
- Real devices vs ideal models: Real springs can be nonlinear and have hysteresis; rolling bodies experience rolling resistance and micro-slip; bearings have drag torque; air drag is quadratic at speed; ropes and pulleys have mass and flexure losses. These appear as non-conservative work W_nc (negative) or additional energy storage terms.
- Energy diagrams and equilibrium (conservative 1-DOF systems): Equilibria occur at dV/dq = 0 (q: generalized coordinate). Stable if d²V/dq² > 0 (local minimum), unstable if < 0 (local maximum), neutral if = 0. This connects to Mechanical Vibrations for small oscillations around minima.
Formulas
dW = F · ds — Infinitesimal work; F is force (N), ds is displacement vector (m); applies in any motion, dot product.
W = F s cosθ — Work by a constant force over straight path; F (N), s (m), θ angle between F and displacement; use for constant F.
W = ∫₁² F · ds — General work along a path; integrates tangential component; F (N), s (m).
W = ∫ₓ₁^ₓ₂ F(x) dx — 1D work under variable force F(x); F (N), x (m); area under F–x curve.
T = 1/2 m v² — Kinetic energy of a particle; m (kg), v (m/s), T (J); always valid for a mass point.
T = 1/2 m v_G² + 1/2 I_G ω² — Kinetic energy of a rigid body; v_G (m/s), I_G (kg·m²), ω (rad/s), T (J); valid in plane/space motion.
T = 1/2 I_O ω² — Kinetic energy for pure rotation about a fixed point O; I_O (kg·m²), ω (rad/s); O must be fixed in inertial frame.
ΣW = ΔT — Work–energy theorem (particle); ΣW total work of all forces (J), ΔT change in KE (J); inertial frame.
ΣW_ext = ΔT — Work–energy (rigid body/system); ΣW_ext external work (J), ΔT total KE change (J); internal work cancels for ideal rigid bodies.
V_g = m g h — Gravitational potential energy near Earth; m (kg), g (9.81 m/s²), h elevation (m) above datum, V_g (J); uniform g assumption.
V_s = 1/2 k x² — Linear spring potential; k stiffness (N/m), x extension/compression from natural length (m), V_s (J); Hooke’s law regime.
W_s = -1/2 k (x₂² - x₁²) — Work done by a linear spring from x₁ to x₂; k (N/m), x (m), W_s (J).
T₁ + V₁ + W_nc = T₂ + V₂ — Energy balance with non-conservative work; W_nc includes friction, actuator work, etc. (J); conservative forces absorbed into V.
P = F · v — Instantaneous power; F (N), v point velocity (m/s), P (W); for any point force.
P = M ω — Rotational power; M torque/couple (N·m), ω (rad/s), P (W); for a torque about axis.
W_M = M θ — Work by a constant torque over rotation θ; M (N·m), θ (rad), W_M (J); sign by sense agreement.
W_g = m g (h₁ - h₂) — Work by weight between elevations h₁ and h₂; m (kg), g (m/s²), h (m), W_g (J); positive when descending.
W_f = - μ_k N s — Work by kinetic friction along sliding distance s; μ_k (–), N normal reaction (N), s (m), W_f (J); direction opposes motion.
v_G = R ω — No-slip rolling constraint; v_G center speed (m/s), R radius (m), ω (rad/s); instantaneous constraint on a stationary surface.
η = E_out / E_in = P_out / P_in — Efficiency; η (–) between 0 and 1, energies (J), powers (W); when input/output clearly defined.
Worked examples
- Direct application: Block on a rough incline Given: m = 10 kg; incline angle θ = 30°; initial speed u = 0; distance along plane s = 2.0 m; coefficient of kinetic friction μ_k = 0.20; g = 9.81 m/s². Find the speed at s.
Steps:
- Forces along the plane: Component of weight down-slope = m g sinθ. Normal reaction N = m g cosθ.
- Work by gravity over s: W_g = m g sinθ · s = 10×9.81×sin30°×2.0 = 98.1 J.
- Work by kinetic friction: W_f = − μ_k N s = −0.20 × (10×9.81×cos30°) × 2.0.
- Compute N = 98.1×cos30° ≈ 98.1×0.8660 ≈ 84.9 N.
- So W_f ≈ −0.20×84.9×2.0 ≈ −33.96 J.
- Net work: W_net = W_g + W_f ≈ 98.1 − 33.96 = 64.14 J.
- Work–energy: W_net = ΔT = 1/2 m v² − 0 ⇒ v = sqrt(2 W_net / m) = sqrt(2×64.14 / 10) m/s.
- Compute inside: 2×64.14/10 = 12.828 ⇒ v ≈ sqrt(12.828) ≈ 3.58 m/s.
Answer: The block’s speed after 2.0 m is 3.58 m/s.
- GATE-style combination: Two masses and a pulley with inertia (energy method) System: Two masses m₁ and m₂ connected by a light inextensible rope over a pulley of radius R and mass moment of inertia I about its axle. The rope does not slip on the pulley; axle friction is negligible. Initially at rest; m₁ > m₂ so m₁ moves down, m₂ up.
Given: m₁ = 6 kg; m₂ = 4 kg; pulley I = 0.50 kg·m²; pulley radius R = 0.20 m; vertical displacement s = 1.0 m; g = 9.81 m/s². Find the common speed v after m₁ descends s.
Steps:
- Choose the system as {m₁, m₂, pulley}. Rope tension does internal work transfers among components; no slip implies v = ωR.
- Potential energy change: m₁ descends s (loss m₁ g s); m₂ rises s (gain m₂ g s). Net loss ΔV = −(m₁ − m₂) g s.
- Numerically: ΔV = −(6 − 4)×9.81×1.0 = −19.62 J (this loss becomes kinetic energy).
- Kinetic energy at displacement s:
- m₁: T₁ = 1/2 m₁ v² = 0.5×6×v² = 3 v² J.
- m₂: T₂ = 1/2 m₂ v² = 0.5×4×v² = 2 v² J.
- Pulley rotation: T_p = 1/2 I ω² = 0.5×0.50×(v/R)² = 0.25×(v² / 0.04) = 6.25 v² J.
- Total T = (3 + 2 + 6.25) v² = 11.25 v² J.
- Energy balance: Loss of potential = gain in kinetic ⇒ (m₁ − m₂) g s = 11.25 v².
- Numerically: 19.62 = 11.25 v² ⇒ v² = 19.62 / 11.25 ≈ 1.744 ⇒ v ≈ 1.321 m/s.
Answer: The speed after m₁ descends 1.0 m is 1.32 m/s.
Assumptions (both examples): Ideal rigid bodies; g = 9.81 m/s²; no air drag; in example 2, massless rope, no slip on pulley, negligible axle friction, and the rope does not stretch.
Common mistakes
- Forgetting rotation energy. For rolling or rotating parts (wheels, pulleys, gears), include 1/2 I ω²; otherwise predicted speeds/accelerations are too high.
- Using v = R ω incorrectly. It holds only at the instantaneous contact when rolling without slip on a stationary surface and relates center speed to angular speed for pure rolling.
- Treating static friction as always zero work. It is zero for pure rolling on a stationary surface because the contact point is instantaneously at rest; but on a moving belt or deformable surface, static friction can do nonzero work.
- Dropping datum consistency. Potential energy differences are what matter; choose a datum and stick with it. Changing datum mid-solution introduces sign errors.
- Confusing external and internal work when selecting the “system.” If you include the pulley in the system, rope tensions are internal; exclude it, and tension can do external work. Be deliberate to simplify.
- Applying conservation of mechanical energy when non-conservative forces act (e.g., kinetic friction). In that case, include W_nc explicitly or use the work–energy theorem with friction work.
For GATE ME
- Compute speed or distance using work–energy with friction and/or springs (block–spring, rough incline, variable F–x).
- Rolling bodies on inclines (solid/hollow cylinder, sphere) comparing accelerations or speeds; sometimes with a spring at the end to find compression.
- Pulley/rope systems with rotating pulleys (finite I), flywheels, or gears—use v = ωR and include rotational KE.
- Power questions: find force or torque needed to maintain a speed against resistances; interpret P–v or F–x plots (area under curve as work).
- Energy in curvilinear motion: use tangential components/work to find speed at a point on a track (loops, dips), often invoking normal reaction separately for contact loss (but contact condition belongs with Kinematics/Forces topics).
- What to practise:
- Setting up T₁ + V₁ + W_nc = T₂ + V₂ with correct signs, including all KE terms (translation + rotation) and spring terms.
- Using F–x graphs to compute work; handling variable forces via integrals.
- Selecting the right system boundary to make constraint forces do zero or internal work.
- Relating v and ω via constraints in belts, pulleys, and rolling.
- Cross-checking with limiting cases: k → 0 (no spring), I → 0 (massless pulley), μ → 0 (smooth surface) to see if answers reduce to simpler known results.
Quick check
- A 2 kg block slides 3 m on a horizontal surface with μ_k = 0.25 starting at 4 m/s. What is its speed at the end? (g = 9.81 m/s²)
- A solid cylinder (I_G = 1/2 mR²) rolls without slipping down an incline dropping height h. What fraction of m g h becomes translational KE at the bottom?
- The torque on a shaft is 40 N·m at 600 rpm. What is the power?
Answers: 1) v = sqrt(4² − 2 μ_k g s) = sqrt(16 − 2×0.25×9.81×3) ≈ 1.69 m/s. 2) Translational fraction = 1 / (1 + I_G/(mR²)) = 1 / (1 + 1/2) = 2/3. 3) P = M ω = 40 × (2π×600/60) ≈ 2.51 kW.
Finished this topic? Mark it so your progress, study plan and readiness keep up.
Stuck on something here?