Plane motion of rigid bodies

Plane motion of rigid bodies: decompose general planar motion into translation plus rotation, use relative velocity/acceleration, instantaneous center, rolling constraint, and Coriolis term for sliders in rotating links.

Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.

Why it matters

Machine links, vehicle wheels, cams, gears, and slider-crank mechanisms all move in a plane. Knowing how to compute velocities and accelerations of any point on a rigid body lets you size actuators, estimate forces later, and check mechanisms quickly in design and in exams.

Key ideas

  • A rigid body is an idealized body whose distances between any two points do not change. In real devices there is small elastic deformation; here we ignore it unless stated.
  • Plane motion means all points of the body move in planes parallel to a fixed reference plane, with a fixed axis of rotation perpendicular to that plane. Thin plates, links, wheels on flat roads often satisfy this approximately.
  1. Decomposition of motion
  • Any general plane motion can be decomposed as the vector sum of a translation of the body plus a rotation about some point (or about an axis perpendicular to the plane). This is kinematics only; no forces are assumed here.
  • Define a reference point A on the body. The motion of any other point B is obtained by adding the motion due to translation of A and the motion due to rotation about A.
  1. Angular kinematics
  • Define angular position θ, angular velocity ω = dθ/dt, and angular acceleration α = dω/dt. For this topic, positive is taken counterclockwise (CCW) unless stated otherwise. Units: ω in rad/s, α in rad/s².
  1. Relative velocity for a rigid body in a plane
  • Exact statement: For any two points A and B on a rigid body in plane motion, the velocity of B is given by v_B = v_A + ω × r_B/A, where r_B/A is the position vector of B relative to A, and the axis of ω is perpendicular to the plane.
  • In 2D component form with k out of plane: if r_B/A = (Δx i + Δy j), then ω k × r_B/A = ω(−Δy i + Δx j). Magnitude of relative velocity equals ω times the distance AB, and it is perpendicular to the line AB.
  • Special cases:
    • Pure translation: ω = 0, so v_B = v_A for all points.
    • Pure rotation about fixed point O: v_P = ω × r_P/O, perpendicular to OP with magnitude ω r.
  1. Relative acceleration for a rigid body in a plane
  • Exact statement: For any two points A and B on a rigid body in plane motion, the acceleration of B is a_B = a_A + α × r_B/A − ω² r_B/A.
  • Interpretation: α × r_B/A is the tangential component (perpendicular to AB), while −ω² r_B/A is the normal component directed from B toward A along AB. In planar components: α k × (Δx i + Δy j) = α(−Δy i + Δx j); and −ω² r_B/A = −ω²(Δx i + Δy j).
  • Special cases:
    • Pure translation: ω = 0, α = 0, so a_B = a_A.
    • Pure rotation about fixed O: a_P = α × r_P/O − ω² r_P/O, with tangential part magnitude α r and normal part magnitude ω² r toward O.
  1. Instantaneous center of zero velocity (IC or ICZV)
  • Exact statement: If a rigid body has a nonzero angular velocity ω at some instant, there exists a unique point I in the plane such that its velocity is zero at that instant, and the velocity of any point P on the body equals v_P = ω × r_P/I.
  • How to locate I: Draw the velocity directions of two noncollinear points on the body. Through each point, draw a line perpendicular to its velocity direction. Their intersection is I. If the body is in pure translation (ω = 0), I is at infinity in the direction perpendicular to the common velocity.
  • Standard results:
    • Pure rotation about fixed O: I coincides with O.
    • Rolling without slipping on a fixed surface: I is at the contact point, and v_contact = 0 instantaneously. Caution: acceleration of that instantaneous contact point on the body is not zero in general; only its velocity is zero.
  • Practical note: IC is powerful for velocity calculations; use the acceleration formula for accelerations (IC does not directly give accelerations unless extra care is taken).
  1. Rolling without slipping
  • No-slip constraint on a wheel or disc of radius R on a fixed surface: the velocity of the contact point relative to ground is zero, so v_O = ω R for the center O, with direction tangent to the path of the center.
  • If ω = 0, it is pure translation and no rolling. If v_O ≠ ω R, there is slip. Real wheels may have small slip or rolling resistance; ideal theory assumes a geometric point contact without slip and without penetration.
  1. Slider-crank and link mechanisms
  • A common planar mechanism has a crank OA rotating at angular speed Ω, a connecting rod AB, and a slider B constrained to move along a straight line. The constraints (pin joints, straight guide) fix directions of some velocities and accelerations.
  • For velocity analysis: use v_B = v_A + ω_AB × r_B/A together with direction constraints (for a slider, v_B is along its guide; for a fixed pin O, v_O = 0). Solve for unknown scalar components and ω_AB.
  • For acceleration analysis with constant Ω: use a_A = −Ω² r_A/O (towards O) and a_B = a_A + α_AB × r_B/A − ω_AB² r_B/A, then apply direction/constraint equations to solve for α_AB and a_B.
  1. Coriolis acceleration in planar mechanisms with sliding on a rotating link
  • Exact statement: If a point P slides with relative velocity v_rel along a slot or link that rotates with angular velocity ω, then in addition to tangential and normal terms, the absolute acceleration gains a Coriolis component a_cor = 2 ω × v_rel. Direction in the plane is obtained by rotating the vector v_rel by 90 degrees in the direction of ω (CCW positive) and multiplying by 2ω in magnitude.
  • Applicability: only when there is relative sliding along a path that itself rotates. If the point is pinned to the rotating link (rigid), there is no Coriolis term.
  1. Sign conventions and modeling assumptions
  • Take CCW positive for ω and α. Rightward i and upward j positive.
  • Units: length in m, velocity in m/s, acceleration in m/s², angles in rad.
  • Rigid joints and zero clearance are assumed. Real mechanisms have backlash, compliance, and friction; those alter responses slightly and are handled in separate topics such as Friction and Kinetics.
  1. Kennedy’s theorem (three centers in a line)
  • Exact statement: For three bodies having plane motion relative to each other, the three instantaneous centers corresponding to each pair of bodies lie on a straight line at any instant. This is useful in linkages to locate ICs graphically.

Outline of key derivations

  • Relative velocity: For a rigid body, the distance AB is constant. Differentiating r_B = r_A + r_B/A with respect to time gives v_B = v_A + d(r_B/A)/dt. Since the rotation is about an axis k with rate ω, d(r_B/A)/dt = ω k × r_B/A.
  • Relative acceleration: Differentiate once more. d²(r_B/A)/dt² = α k × r_B/A + ω k × (ω k × r_B/A) = α × r_B/A − ω² r_B/A.
  • Rolling no-slip: Enforce v_contact = 0 to relate v_O and ω via the relation v_O = ω R; do not set a_contact = 0 unless specifically analyzing the ground point, because the material point in contact at that instant will not remain in contact.

Why real devices differ from the ideal

  • Small elastic strains alter instantaneous distances slightly, violating rigid-body assumptions at high speeds.
  • Slip occurs due to limited friction; then v_O ≠ ω R and IC is not exactly at contact.
  • Clearances in pins cause small impacts, affecting acceleration spikes not captured by smooth rigid kinematics.

Formulas

v_B = v_A + ω × r_B/A

  • v_A, v_B: velocities of points A, B (m/s). ω: angular velocity vector perpendicular to plane (rad/s). r_B/A: position vector from A to B (m). Applies to any two points on the same rigid body in plane motion.

a_B = a_A + α × r_B/A − ω² r_B/A

  • a_A, a_B: accelerations of points A, B (m/s²). α: angular acceleration vector (rad/s²). ω: angular velocity magnitude (rad/s). r_B/A: position vector from A to B (m). Applies to any two points on the same rigid body in plane motion.

v_P = ω × r_P/O

  • v_P: velocity of point P on a body rotating about fixed point O (m/s). ω: angular velocity (rad/s). r_P/O: position vector from O to P (m). Pure rotation about fixed O.

a_P = α × r_P/O − ω² r_P/O

  • a_P: acceleration of P (m/s²). α: angular acceleration (rad/s²). ω: angular velocity (rad/s). r_P/O: position vector from O to P (m). Pure rotation about fixed O.

v_O = ω R

  • v_O: speed of center of a rolling wheel (m/s). ω: angular speed (rad/s). R: radius (m). Rolling without slipping on a fixed surface; direction tangent to path of center.

a_cor = 2 ω × v_rel

  • a_cor: Coriolis acceleration (m/s²). ω: angular velocity of the rotating path or link (rad/s). v_rel: velocity of sliding relative to the rotating path (m/s). Applies when a point slides along a rotating link or slot.

v_P = ω r and a_t = α r, a_n = ω² r

  • Magnitudes for a point at radius r from the rotation center. v_P speed (m/s). a_t tangential acceleration (m/s²). a_n normal acceleration (m/s²). Pure rotation.

x_slider = r cos θ + √(l² − r² sin² θ)

  • x_slider: displacement of slider along its guide measured from crank center line (m). r: crank length (m). l: connecting rod length (m). θ: crank angle from line of stroke (rad). Ideal slider-crank geometry (planar, pin joints).

Worked examples

Example 1 — Direct rigid rotation about a fixed point Given: A disc of radius R = 0.20 m rotates CCW about its center O with angular velocity ω = 10 rad/s and angular acceleration α = 15 rad/s². Find the velocity and acceleration components of a rim point P located at θ = 30 degrees above the positive x-axis. Assumptions: Rigid disc, pure rotation about fixed O, CCW positive.

Steps

  1. Velocity of P: use v_P = ω × r, components v_x = − ω R sin θ, v_y = ω R cos θ.
    • Numbers: sin 30° = 0.5, cos 30° = 0.8660.
    • v_x = − 10 × 0.20 × 0.5 = −1.00 m/s.
    • v_y = 10 × 0.20 × 0.8660 = 1.732 m/s.
    • Speed check: |v| = ω R = 2.00 m/s (consistent with components).
  2. Acceleration of P: a_P = α × r − ω² r. Components a_x = − α R sin θ − ω² R cos θ, a_y = α R cos θ − ω² R sin θ.
    • ω² R = 100 × 0.20 = 20.0 m/s²; α R = 15 × 0.20 = 3.0 m/s².
    • a_x = − 3.0 × 0.5 − 20.0 × 0.8660 = −1.50 − 17.320 = −18.820 m/s².
    • a_y = 3.0 × 0.8660 − 20.0 × 0.5 = 2.598 − 10.0 = −7.402 m/s².

Answer: Velocity v_P = (−1.00 i + 1.732 j) m/s; Acceleration a_P = (−18.82 i − 7.40 j) m/s². Magnitudes: |v_P| = 2.00 m/s, |a_P| ≈ 20.22 m/s². Final answers: v_P components and a_P components as above in SI units.

Example 2 — Slider-crank kinematics at a given crank angle (GATE-level) Given: Crank OA of length r = 50 mm rotates CCW at constant Ω = 300 rpm. Connecting rod AB length l = 200 mm. Slider B moves along a horizontal guide through O. At the instant when crank angle θ = 60 degrees from the line of stroke, find (i) slider velocity v_B, (ii) slider acceleration a_B, (iii) angular velocity ω_AB, and (iv) angular acceleration α_AB of the connecting rod. Assumptions: Planar, rigid links, ideal pin joints, uniform Ω (α_OA = 0), CCW positive, SI units. Data in SI: r = 0.050 m; l = 0.200 m; Ω = 300 rpm = 300 × 2π / 60 = 10π ≈ 31.416 rad/s; θ = 60° so sin θ = 0.8660, cos θ = 0.5. Geometry: A has coordinates (x_A, y_A) = (r cos θ, r sin θ) = (0.0250, 0.04330) m. The slider is at y = 0. From geometry, along AB: Δx = x_B − x_A = √(l² − r² sin² θ) = √(0.0400 − 0.0025 × 0.75) = √(0.038125) ≈ 0.19526 m. Also Δy = y_B − y_A = − y_A = −0.04330 m.

Step 1: Velocity of crank pin A

  • v_A magnitude: r Ω = 0.050 × 31.416 = 1.5708 m/s.
  • Components: v_Ax = − r Ω sin θ = −1.3603 m/s; v_Ay = r Ω cos θ = 0.7854 m/s.

Step 2: Relative velocity relation for rod AB

  • v_B = v_A + ω_AB × r_B/A. In components: v_Bx = v_Ax + ω_AB y_A; v_By = v_Ay + ω_AB Δx.
  • Constraint: slider moves horizontally, so v_By = 0.
  • Solve for ω_AB: 0 = v_Ay + ω_AB Δx ⇒ ω_AB = − v_Ay / Δx = − 0.7854 / 0.19526 ≈ −4.02 rad/s (negative means clockwise at this instant).
  • Slider velocity: v_Bx = v_Ax + ω_AB y_A = −1.3603 + (−4.02) × 0.04330 ≈ −1.3603 − 0.1741 = −1.5344 m/s.

Step 3: Acceleration of crank pin A (constant Ω)

  • a_A = − Ω² r_A/O, components: a_Ax = − r Ω² cos θ, a_Ay = − r Ω² sin θ.
  • Compute r Ω² = 0.050 × (31.416)² ≈ 49.348 m/s².
  • a_Ax = − 49.348 × 0.5 = −24.674 m/s²; a_Ay = − 49.348 × 0.8660 = −42.746 m/s².

Step 4: Relative acceleration relation for rod AB

  • a_B = a_A + α_AB × r_B/A − ω_AB² r_B/A.
  • Components: a_Bx = a_Ax + α_AB y_A − ω_AB² Δx; a_By = a_Ay + α_AB Δx + ω_AB² y_A.
  • Constraint: a_By = 0 for the slider.
  • Solve for α_AB: 0 = a_Ay + α_AB Δx + ω_AB² y_A ⇒ α_AB = − (a_Ay + ω_AB² y_A) / Δx.
  • Numbers: ω_AB² ≈ (−4.02)² = 16.160; ω_AB² y_A ≈ 16.160 × 0.04330 ≈ 0.700 m/s².
  • α_AB ≈ − (−42.746 + 0.700) / 0.19526 = 42.046 / 0.19526 ≈ 215.3 rad/s² (CCW).
  • Slider acceleration: a_Bx = a_Ax + α_AB y_A − ω_AB² Δx ≈ −24.674 + (215.3 × 0.04330) − (16.160 × 0.19526) ≈ −24.674 + 9.323 − 3.155 ≈ −18.51 m/s².

Answers:

  • Slider velocity v_B ≈ −1.534 m/s (to the left along the guide).
  • Slider acceleration a_B ≈ −18.51 m/s² (to the left).
  • Angular velocity of rod ω_AB ≈ −4.02 rad/s (clockwise).
  • Angular acceleration of rod α_AB ≈ +215.3 rad/s² (counterclockwise).

Checks:

  • Direction consistency: At θ = 60° with CCW crank, the slider moving toward the crank (negative x) is expected at this position.
  • Dimensions: all velocities in m/s, accelerations in m/s², angular rates in rad/s and rad/s².

Common mistakes

  • Dropping the normal term −ω² r_B/A in acceleration, leading to large errors; remember both tangential (α × r) and normal (ω² r toward center) parts.
  • Using the instantaneous center to compute accelerations directly or assuming the acceleration at the IC is zero. IC guarantees zero velocity only, not zero acceleration.
  • Assigning the wrong sign for ω and α; define CCW positive and stick to it. Always carry vector directions or i, j components.
  • Assuming rolling without slipping implies zero acceleration at the contact point; only the instantaneous velocity is zero.
  • Mixing units (mm with m, rpm with rad/s). Convert at the start.
  • In slider-crank, forgetting that v_By = 0 and a_By = 0 constraints come from the guide, not from the rod.
  • Coriolis acceleration direction errors; use the 90-degree rule in the direction of ω and the factor 2.

For GATE ME

  • Quick kinematics of links: compute velocity and acceleration of a point on a rotating link given ω and α, often at a specified angle. Practise component calculations and vector directions.
  • Relative velocity and acceleration in slider-crank: solve for slider velocity/acceleration and rod ω, α at a given θ. Practise setting up two scalar equations from constraints (e.g., v_By = 0, a_By = 0).
  • Instantaneous center method for velocity: locate IC by perpendiculars to velocities to get speeds of points, including rolling discs and linkages. Be ready for conceptual MCQs where the IC is at infinity for pure translation.
  • Rolling without slipping: relate v_O and ω, speed of specific points on the rim, and directions. Focus on why acceleration at contact is not zero.
  • Coriolis acceleration: sliders in rotating slots, compute a_cor = 2 ω × v_rel and add to other terms. Expect direction tests and magnitude estimates.
  • Kennedy’s theorem in mechanisms: identify the three ICs and use collinearity to find an unknown IC for velocity calculations.
  • Practise: draw neat kinematic diagrams, annotate known directions, write vector equations first, then substitute numbers. Do a dimensional check before final answers.

Quick check

  1. A rigid rod AB rotates about a fixed point A with ω = 12 rad/s CCW and α = 0. What are the magnitudes of tangential and normal accelerations of a point 0.3 m from A?
  2. For a wheel rolling without slipping at speed v_O = 5 m/s, what is the instantaneous speed of the topmost point on the rim relative to ground?
  3. A slider moves in a slot of a link rotating at ω = 6 rad/s. If the slider’s speed relative to the slot is 0.8 m/s outward along the slot, what is the magnitude of Coriolis acceleration?

Answers: 1) a_t = α r = 0, a_n = ω² r = 43.2 m/s². 2) 2 v_O = 10 m/s. 3) a_cor = 2 ω v_rel = 9.6 m/s².

Finished this topic? Mark it so your progress, study plan and readiness keep up.

Stuck on something here?