Mechanical Engineering (University) is coming soon

We're still writing and reviewing the notes for every subject, and we'll open it when every subject is ready. Meanwhile you can practise aptitude, ask Aria about any subject, or see the branches that are ready.

Moment of inertia

Moment of inertia (mass and area), parallel and perpendicular axis theorems, radius of gyration, standard formulas for common shapes, and composite/shift calculations with examples.

Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.

Why it matters

  • Transfer inertias between axes (machine design, robotics) and compute composite sections (structural design).

Key ideas

  • Definition: Polar moment of inertia (area) about a point O (z-axis perpendicular to the plane) is J_O = ∫ r² dA, where r² = x² + y². Units: m⁴. It is used in torsion of circular shafts.
  • Theorem (Perpendicular Axis, for plane areas): “For a plane area lying in the x–y plane, the polar moment of inertia about the z-axis through point O (perpendicular to the plane) equals the sum of its moments of inertia about two mutually perpendicular axes x and y through O in the plane: J_O = Iₓ + Iᵧ.” Assumptions: thin plane area; axes intersect at O and are mutually perpendicular.
    • Derivation outline: At a point (x, y), r² = x² + y², so J_O = ∫ r² dA = ∫ (x² + y²) dA = ∫ x² dA + ∫ y² dA = Iᵧ + Iₓ. Diagram to draw: x and y axes in the plane, z-axis out of plane at O; show a small dA at (x, y), label x, y, r.
  • Theorem (Parallel Axis): For a plane area of total area A, “The moment of inertia about any axis parallel to an axis through the centroid G is I = I_G + A d², where d is the perpendicular distance between the axes.” For mass: “I = I_G + m d².” Assumptions: same orientation of axes; centroid is correctly located.
    • Derivation outline (area): For axis X–X at distance d from centroidal axis G–G: Iₓ = ∫ y² dA = ∫ (y_G + d)² dA = ∫ (y_G² + 2 d y_G + d²) dA = I_G + 2 d ∫ y_G dA + d² ∫ dA. Since ∫ y_G dA = 0 (definition of centroid), Iₓ = I_G + A d². Diagram to draw: two parallel horizontal axes, centroid G marked, offset d shown; show a strip dA at distance y_G from G–G.
  • Definition: Radius of gyration about a given axis is “the distance k from the axis at which the entire area (or mass) can be assumed concentrated without changing the moment of inertia about that axis.” Formulas: k = √(I/A) for area, k = √(I/m) for mass. Units: m.
  • Standard centroidal axes and symmetry: For shapes with symmetry about an axis, the centroidal axis lies on the symmetry line and the product of inertia I_xy about centroidal axes aligned with the symmetry axes is zero. Definition: I_xy = ∫ x y dA (used in advanced topics like principal axes; not used directly in basic bending formulas).
  • Derivations commonly asked:
    1. Rectangle (b × h) about centroidal x-axis: Divide into horizontal strips of thickness dy at distance y from the centroid (origin at centroid). dA = b dy; Iₓ = ∫ y² dA = b ∫{-h/2}^{h/2} y² dy = b [y³/3]{-h/2}^{h/2} = b (2 (h/2)³ /3) = b h³ /12. Diagram: rectangle, centroid at center, x-axis through centroid parallel to base; show a strip b × dy at y.
    2. Triangle (base b on x-axis, height h on y-axis) about base: At a distance y above base, strip width w(y) = b (1 − y/h). dA = w dy. I_base = ∫ y² dA = ∫₀^h y² b (1 − y/h) dy = b [y³/3 − y⁴/(4 h)]₀^h = b (h³/3 − h³/4) = b h³ /12. Then, centroidal I parallel to base: I_G = I_base − A d², where A = b h/2 and d = h/3: I_G = (b h³/12) − (b h/2)(h²/9) = (b h³/12 − b h³/18) = b h³/36. Diagram: right triangle with base on x-axis, vertical y; strip at height y with width w(y).
    3. Circle (radius R) about a centroidal diameter (x or y): Use polar form or standard result: Iₓ = Iᵧ = (π R⁴)/4. Polar J_O = Iₓ + Iᵧ = (π R⁴)/2. Diagram: circle centered at O with x and y diameters shown.

Formulas

  • Iᵧ = ∫ x² dA — AMOI about y-axis; x (m); dA (m²); Iᵧ (m⁴); use for bending about y.
  • J_O = ∫ r² dA = Iₓ + Iᵧ — Polar AMOI about point O (z-axis); r² = x² + y²; J_O (m⁴); use for torsion of circular sections; perpendicular axis theorem applies to plane areas.
  • I = I_G + m d² — Parallel axis (mass); I about any axis; I_G about parallel centroidal axis; m (kg); d (m).
  • I = I_G + A d² — Parallel axis (area); I about any axis; I_G about parallel centroidal axis; A (m²); d (m).
  • k = √(I/m) — Radius of gyration for mass; k (m); I (kg·m²); m (kg).
  • k = √(I/A) — Radius of gyration for area; k (m); I (m⁴); A (m²).
  • Iₓ(rectangle, centroidal) = b·h³/12 — b (m): width along x; h (m): depth along y; Iₓ (m⁴); axis through centroid parallel to base.
  • Iᵧ(rectangle, centroidal) = h·b³/12 — Iᵧ (m⁴); axis through centroid parallel to side.
  • I_base(rectangle) = b·h³/3 — about base side of height h; via parallel axis from centroidal.
  • I_base(triangle) = b·h³/12 — base (m), height (m); axis along base.
  • I_centroidal‖base(triangle) = b·h³/36 — centroidal axis parallel to base through centroid.
  • I(about centroidal diameter of circle) = (π·R⁴)/4 = (π·D⁴)/64 — R (m), D (m = 2R); I (m⁴); about x or y diameter.
  • J_O(circle) = (π·R⁴)/2 = (π·D⁴)/32 — polar AMOI (m⁴) about center.
  • I(hollow circle, centroidal diameter) = (π/64)·(D_o⁴ − D_i⁴) — D_o, D_i in m; I (m⁴).
  • I(composite area) = Σ I_part (about the same axis) — add for material present; subtract for holes; include parallel-axis shifts for each part to the common reference axis.
  • I_end(slender rod, perpendicular to length) = (1/3)·m·L² — MMOI about end; L (m), m (kg).
  • I_centroid(slender rod, midpoint) = (1/12)·m·L² — MMOI about centroidal axis perpendicular to length.
  • I(disk, about central axis) = (1/2)·m·R² — MMOI of solid circular disk about axis normal to disk through center.
  • I(thin hoop/ring, about central axis) = m·R² — MMOI when mass concentrated at radius R.

Worked examples

Example 1: Area MOI of a rectangular plate with a central circular hole Given: A rectangular plate, width b = 300 mm, height h = 400 mm, with a central circular hole of diameter D = 150 mm. Find (a) Iₓ through the centroidal horizontal axis, (b) Iᵧ through the centroidal vertical axis, and (c) Iₓ about the bottom edge (base). Use SI units.

  1. Convert to meters:
    • b = 0.300 m, h = 0.400 m, D = 0.150 m; R = D/2 = 0.075 m.
  2. Areas:
    • Rectangle: A_rect = b·h = 0.300 × 0.400 = 0.120 m².
    • Hole (circle): A_hole = π·R² = π × 0.075² = π × 0.005625 = 0.01767146 m² (rounded to 7 significant figures).
    • Net area: A_net = A_rect − A_hole = 0.120 − 0.01767146 = 0.10232854 m² (rounded to 8 significant figures; 0.1023285 m² to 7 significant figures).
  3. Moments of inertia about centroidal axes (hole is central, so same centroid):
    • Rectangle about centroidal x-axis: Iₓ_rect = b·h³/12 = 0.300 × 0.400³ / 12 = 0.300 × 0.064 / 12 = 0.0192 / 12 = 0.0016 m⁴.
    • Rectangle about centroidal y-axis: Iᵧ_rect = h·b³/12 = 0.400 × 0.300³ / 12 = 0.400 × 0.027 / 12 = 0.0108 / 12 = 0.0009 m⁴.
    • Hole (circle) about centroidal diameter: Iₓ_hole = Iᵧ_hole = (π·R⁴)/4. Compute R⁴: 0.075² = 0.005625; (0.005625)² = 0.000031640625. Then Iₓ_hole = Iᵧ_hole = (π/4) × 0.000031640625 = 0.785398163 × 0.000031640625 = 0.00002485049 m⁴ (to 7 significant figures: 2.485049×10⁻⁵ m⁴).
  4. Net centroidal MOI (subtract the hole):
    • Iₓ_centroid = Iₓ_rect − Iₓ_hole = 0.0016 − 0.00002485049 = 0.00157514951 m⁴.
    • Iᵧ_centroid = Iᵧ_rect − Iᵧ_hole = 0.0009 − 0.00002485049 = 0.00087514951 m⁴.
  5. Shift Iₓ to the bottom edge (base) using parallel axis. Distance from centroidal x-axis to base is d = h/2 = 0.200 m. Use net area for the shift:
    • Iₓ_base = Iₓ_centroid + A_net·d² = 0.00157514951 + 0.1023285 × 0.200² = 0.00157514951 + 0.1023285 × 0.040 = 0.00157514951 + 0.00409314 = 0.00566828951 m⁴.

Answer: (a) Iₓ(centroid) = 0.00157514951 m⁴; (b) Iᵧ(centroid) = 0.00087514951 m⁴; (c) Iₓ(base) = 0.00566828951 m⁴. Final answers in engineering notation: (a) 1.57515×10⁻³ m⁴; (b) 8.75150×10⁻⁴ m⁴; (c) 5.66829×10⁻³ m⁴. Keep guard digits in intermediate steps; round consistently (e.g., 6–7 significant figures) only at the end.

Example 2: MMOI of a solid disk and shift to a parallel axis Given: Solid steel disk, mass m = 10.0 kg, radius R = 0.200 m. Find (a) MMOI about its central axis normal to the disk, (b) MMOI about a parallel axis 0.50 m away.

  1. About the central axis (z through center): Formula I_c = (1/2)·m·R².
    • I_c = 0.5 × 10.0 × (0.200)² = 5.0 × 0.040 = 0.200 kg·m².
  2. About a parallel axis at distance d = 0.50 m: Use parallel axis (mass) I = I_G + m d².
    • I = 0.200 + 10.0 × (0.50)² = 0.200 + 10.0 × 0.25 = 0.200 + 2.50 = 2.700 kg·m².

Answer: (a) 0.200 kg·m²; (b) 2.700 kg·m². Both to 3 significant figures.

Example 3: Slender rod — MMOI about end, and radius of gyration Given: Uniform slender rod, length L = 1.20 m, mass m = 4.00 kg. Find (a) MMOI about an axis through one end, perpendicular to the rod, (b) MMOI about centroidal axis, (c) radius of gyration about the end axis.

  1. MMOI about end: I_end = (1/3)·m·L² = (1/3) × 4.00 × (1.20)² = (1/3) × 4.00 × 1.44 = (1/3) × 5.76 = 1.92 kg·m².
  2. MMOI about centroid (midpoint): I_centroid = (1/12)·m·L² = (1/12) × 4.00 × 1.44 = (4.00 × 1.44)/12 = 5.76/12 = 0.480 kg·m².
  3. Radius of gyration about end: k_end = √(I_end/m) = √(1.92 / 4.00) = √(0.480) = 0.6928 m (rounded to 4 significant figures).

Answer: (a) 1.92 kg·m²; (b) 0.480 kg·m²; (c) k_end = 0.693 m (3 significant figures).

How to present diagrams in exams (describe and draw):

  • Show the body/area with clearly labeled dimensions.
  • Mark centroid G where known. Draw reference axes with arrow directions and names (x, y, z); indicate distances d for parallel-axis shifts.
  • For integration proofs, draw a typical elemental strip dA with its location variable (x or y) and thickness (dx or dy); label w(y) if width varies.

Common mistakes

  • Forgetting to subtract holes or forgetting to apply parallel-axis shift to each part to the same axis before adding.
  • Using diameter in a radius-based formula without converting, or vice versa. For a circle: I = (π·R⁴)/4 = (π·D⁴)/64 — do not mix R and D.
  • Assuming the centroid of a composite area stays at the geometric center after removing/adding asymmetrical parts; first locate centroid, then compute MOI.
  • Dropping units in intermediate steps; this hides errors and loses marks.
  • Rounding too early; keep guard digits to avoid cumulative error, round only at the end.

For your exam

  • Derivations: Standard derivations for I of rectangle about centroidal axis; triangle about base and then centroidal via parallel axis; circle about centroidal diameter (give final form and, if deriving, show the integral setup in polar coordinates or use perpendicular axis with polar J_O).
  • Numericals: Composite areas (with cutouts or additions), shifting to non-centroidal axes; MMOI of standard bodies (rods, disks, rings) and transfers using parallel axis. Always: 1) sketch, 2) write formulas before substituting, 3) carry SI units, 4) box final answers.
  • Diagrams: Clean, labeled axes, dimensions, centroid G, distances for shifts, and elemental strips for integration.
  • Short notes: Radius of gyration meaning and use; difference between AMOI and MMOI; when J = Iₓ + Iᵧ applies.

Quick check

  1. Write the parallel-axis theorem for (a) area and (b) mass, define each symbol.
  2. A rectangle 200 mm × 300 mm has Iₓ(centroid) = ? Give in m⁴.
  3. A thin hoop of mass 2 kg and radius 0.4 m has MMOI about its central axis = ?

Answers: (1) Area: I = I_G + A d²; Mass: I = I_G + m d²; where I is MOI about any axis, I_G is MOI about parallel centroidal axis, A is area (m²), m is mass (kg), d is perpendicular distance (m). (2) Iₓ = b·h³/12 = 0.200 × 0.300³ / 12 = 0.200 × 0.027 / 12 = 0.00045 m⁴. (3) I = m·R² = 2 × 0.4² = 0.32 kg·m².

Finished this topic? Mark it so your progress, study plan and readiness keep up.

Stuck on something here?