Mechanical Engineering (University) is coming soon

We're still writing and reviewing the notes for every subject, and we'll open it when every subject is ready. Meanwhile you can practise aptitude, ask Aria about any subject, or see the branches that are ready.

Friction and belt friction

Basics of dry friction and belt (capstan) friction, including laws, angle of friction, angle of repose, cone of friction, capstan equation for flat and V-belts, and related calculations.

Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.

Why it matters

Key ideas

  • Limiting friction (Fmax): The maximum possible static friction just before motion begins. Law: Fmax = μs·N, where μs is the coefficient of static friction.
  • Kinetic (sliding) friction (Fk): Friction during relative motion. Law: Fk = μk·N, with μk ≤ μs.
  • Coefficient of friction (μ): A dimensionless constant that depends on the pair of surfaces and their condition. Separate values are used for static (μs) and kinetic (μk) friction.
  • Angle of friction (φ): The angle between the resultant reaction and the normal reaction at limiting equilibrium. Exact statement: At the onset of sliding, tan φ = μs. Assumptions: rigid bodies, dry surfaces, friction proportional to normal reaction, and independent of apparent area for given N.
  • Angle of repose (θr): The maximum angle of an inclined plane at which a body at rest is on the point of sliding down due to its own weight. Exact result: For impending motion down the plane, tan θr = μs. Hence, θr = φ.
  • Cone of friction: For a 3D contact with all possible directions of impending motion, the locus of resultant reactions at limiting equilibrium forms a right circular cone with semi-vertical angle φ (angle of friction). If the resultant lies inside the cone, no motion occurs; on the surface, impending motion; outside, motion occurs.

Derivations commonly asked

  1. Angle of friction relation tan φ = μ
  • Consider a block at limiting equilibrium on a rough horizontal plane under a horizontal force P. Friction acts opposite to P with magnitude Fmax = μs·N. Resultant reaction R is vector sum of N and Fmax. So tan φ = Fmax / N = μs.

Diagram to draw: A block on a horizontal plane. Show N upward, W downward (weight), P to the right, friction F to the left at contact. Show resultant R making angle φ with the normal.

  1. Angle of repose equals angle of friction
  • Block of weight W on a rough inclined plane at angle θ with horizontal. For impending motion downwards:
    • Components of W: along plane W sin θ, normal to plane W cos θ.
    • Normal reaction N = W cos θ.
    • Limiting friction Fmax = μs N = μs W cos θ acts up the plane.
    • Equilibrium along plane at impending motion: W sin θ = Fmax = μs W cos θ ⇒ tan θ = μs.
    • At limiting condition, θ = θr and tan θr = μs. Also tan φ = μs, hence θr = φ.

Diagram to draw: Inclined plane at angle θ, block on it. Show W vertically down, resolve into W sin θ along plane (downwards) and W cos θ normal to plane. Show N perpendicular to plane, friction up the plane at impending down-slope motion.

  1. Capstan (belt friction) equation for a flat belt/rope: T1/T2 = e^(μθ)
  • System: A flexible belt or rope on a fixed rough cylinder/pulley. T1 is the larger (tight) side tension, T2 is the smaller (slack) side tension. θ is the wrap/contact angle in radians. Assume: perfectly flexible, inextensible belt; uniform normal pressure; no belt mass or centrifugal effects; impending slip condition (limiting friction) everywhere in contact.
  • Consider an elemental belt segment subtending small angle dθ at the pulley center. Let belt tension at the start be T and at the end be T + dT. Normal reaction on element dN directed radially. Friction force magnitude μ dN, direction opposite to motion tendency, tangential.
  • Force balance on the element:
    • Radial (normal) equilibrium: dN = T dθ (using small-angle approximation, resultant of T at ends ≈ T dθ radially). Strictly, radial component sum ≈ T dθ when dθ is small.
    • Tangential (along belt) equilibrium at limiting friction: dT = μ dN = μ T dθ.
  • Separate variables and integrate from slack to tight side:
    • ∫(dT/T) = μ ∫ dθ ⇒ ln(T1/T2) = μ θ ⇒ T1/T2 = e^(μ θ).

Diagram to draw: Circle for pulley. Small belt element subtending dθ at contact. Show T at one end, T + dT at the other, dN pointing to pulley center, friction μ dN tangential opposite impending motion. Indicate wrap angle θ from entry to exit.

  1. V-belt (grooved pulley) modification
  • When the belt runs in a V-groove of included groove angle β, the effective normal reaction increases. The capstan formula becomes T1/T2 = e^(μ' θ) with μ' = μ / sin(β/2) under the same assumptions as above. This result comes from resolving forces on both sides of the groove; the net normal reaction is higher by the factor 1/sin(β/2).
  1. Power transmitted by a belt (basic, ignoring belt mass and slip)
  • Power P is force times velocity along the belt: P = (T1 − T2) · v, where v is belt linear speed. Assumptions: steady state, no slip or negligible slip, belt mass neglected (so centrifugal effects ignored), flat belt unless otherwise stated.
  1. Centrifugal tension (at high belt speeds)
  • If belt mass per unit length is m, the moving belt experiences centrifugal tension Tc due to rotation over the pulley. For steady circular motion along the pulley arc, Tc = m v² acting equally on tight and slack sides. This reduces the effective belt tensions available for friction/power by Tc. Common design relation for maximum power (with friction and pulley sized accordingly) is: Maximum power occurs when Tc = T/3, where T is the maximum permissible belt tension (due to strength). Then v_max = √(T / (3 m)). Use these only when the problem states or implies centrifugal effects. In such cases, use the modified tension ratio: (T1 − Tc)/(T2 − Tc) = e^(μ θ).

Formulas

  • Fk = μk·N
    • Fk: kinetic (sliding) friction (N). μk: coefficient of kinetic friction (dimensionless). N: normal reaction (N). Applies during steady sliding.
  • tan φ = μs
    • φ: angle of friction (rad or deg). μs: coefficient of static friction (dimensionless). At limiting equilibrium.
  • tan θr = μs
    • θr: angle of repose (rad or deg). μs: coefficient of static friction (dimensionless). For a block on an inclined plane at impending motion.
  • T1/T2 = e^(μ θ)
    • T1: tight side tension (N). T2: slack side tension (N). μ: coefficient of friction (dimensionless). θ: wrap angle in radians. Flat belt/rope, impending slip, no belt mass/centrifugal effects.
  • T1/T2 = e^( (μ / sin(β/2)) · θ )
    • β: groove angle of V-belt pulley (rad or deg; use sin of half-angle). Others as above. For V-belts under impending slip.
  • P = (T1 − T2) · v
    • P: power (W). T1, T2: N. v: belt speed (m/s). For belt drives without significant slip/centrifugal effects.
  • v = π D n
    • v: belt speed (m/s). D: pulley diameter (m). n: pulley rotational speed (rev/s). For a belt on a pulley of diameter D rotating at n revolutions per second.
  • Tc = m v²
    • Tc: centrifugal tension per side (N). m: belt mass per unit length (kg/m). v: belt speed (m/s). For high-speed belts; acts on both sides.
  • v_max = √(T / (3 m))
    • v_max: belt speed for maximum power (m/s). T: maximum permissible belt tension (N). m: belt mass per unit length (kg/m). Applies when including centrifugal tension and the standard maximum power criterion.

Worked examples

Given: A rope is wrapped 2.5 turns around a fixed bollard. Coefficient of friction μ = 0.3. The load tension on the tight side is T1 = 8.0 kN. Find the minimum holding force T2 at the free end.

Steps:

  1. Data: Number of turns = 2.5 ⇒ wrap angle θ = 2.5 · 2π = 5π rad ≈ 15.708 rad. μ = 0.3. T1 = 8.0 kN = 8000 N.
  2. Formula: T1/T2 = e^(μ θ) ⇒ T2 = T1 / e^(μ θ).
  3. Substitute: Exponent μ θ = 0.3 × 15.708 = 4.7124. Then e^(4.7124) ≈ 111.32 (checked).
  4. Compute: T2 = 8000 N / 111.32 ≈ 71.9 N.

Answer: The minimum holding force is approximately 72 N (to two significant figures).

  1. Flat belt drive — tensions and power Given: A flat belt runs over a 0.50 m diameter pulley with angle of contact θ = 160°. Coefficient of friction μ = 0.28. Pulley speed = 600 rpm. Maximum belt tension (allowed by strength) T = 1000 N. Assume belt mass is negligible and no slip. Find (a) T1, T2, and (b) power transmitted.

Steps:

  1. Convert angle: θ = 160° = 160 × (π/180) = 2.7925 rad.
  2. Tension ratio: T1/T2 = e^(μ θ) = e^(0.28 × 2.7925) = e^(0.7819) ≈ 2.185.
  3. With negligible mass and given maximum tension limiting tight side, take T1 = T = 1000 N. Then T2 = T1 / 2.185 = 1000 / 2.185 = 457.9 N.
  4. Belt speed: v = π D n. Here D = 0.50 m, n = 600 rpm = 10 rps. So v = π × 0.50 × 10 = 5π = 15.708 m/s.
  5. Power: P = (T1 − T2) v = (1000 − 457.9) N × 15.708 m/s = 542.1 × 15.708 = 8514 W.

Answers: (a) T1 ≈ 1000 N, T2 ≈ 458 N; (b) Power ≈ 8.51 kW.

  1. V-belt on a grooved pulley — required tight-side tension Given: A V-belt runs in a pulley with groove angle β = 40°. μ between belt and groove faces = 0.22. Angle of contact θ = 150° on the pulley. The slack-side tension T2 must be at least 300 N to avoid belt flutter. Find the required tight-side tension T1 for impending slip.

Steps:

  1. Convert: β/2 = 20°, so sin(β/2) = sin 20° = 0.3420 (checked). Effective friction μ' = μ / sin(β/2) = 0.22 / 0.3420 = 0.643.
  2. Convert θ: θ = 150° = 150 × π/180 = 2.6180 rad.
  3. Tension ratio: T1/T2 = e^(μ' θ) = e^(0.643 × 2.6180) = e^(1.684) = 5.388.
  4. Compute T1: T1 = 5.388 × 300 N = 1616 N.

Answer: The required tight-side tension is approximately 1.62 kN.

Note: If the problem requires power, compute P = (T1 − T2) v using the belt speed.

Common mistakes

  • Taking the given maximum belt tension as the net tight-side tension without checking centrifugal effects when belt speeds are high. If m and speed are significant, reduce the available tight- and slack-side tensions by Tc.
  • Forgetting that for V-belts the effective friction is μ / sin(β/2), not μ × sin(β/2).
  • Reversing tight and slack sides or computing T2/T1 instead of T1/T2.
  • Not carrying units and not checking reasonableness (e.g., a tiny holding force with many wraps is expected; the opposite suggests a mistake).

For your exam

  • Numericals: Typical problems include computing holding force on a rope with multiple turns; determining T1, T2, and power for a belt drive; V-belt tension ratio; including belt speed from pulley dimensions and rpm. Sometimes include centrifugal tension and maximum power speed; write assumptions clearly if you use them.
  • Diagrams: Free-body diagrams of a block on a plane; the belt elemental segment on a pulley showing T, T + dT, dN, μ dN; V-groove contact with resolved normals. Label all forces and angles.
  • Full-marks answers: Begin with a clean FBD, state assumptions, write governing equations symbolically before substituting numbers, keep units throughout, and present a boxed or bold final answer with appropriate significant figures.

Quick check

  1. The angle of friction is 20°. What is μs?
  2. A flat belt wraps 200° around a pulley, μ = 0.25. What is T1/T2? (Use radians.)
  3. A V-belt has β = 30°. If μ = 0.20, what is the effective μ' for tension ratio calculations?

Answers: 1) μs = tan 20° ≈ 0.364; 2) θ = 200° = 3.4907 rad ⇒ T1/T2 = e^(0.25 × 3.4907) = e^(0.8727) ≈ 2.39; 3) μ' = μ / sin(β/2) = 0.20 / sin 15° = 0.20 / 0.2588 ≈ 0.773.

Finished this topic? Mark it so your progress, study plan and readiness keep up.

Stuck on something here?