First Year Engineering is coming soon

We're still writing and reviewing the notes for every subject, and we'll open it when every subject is ready. Meanwhile you can practise aptitude, ask Aria about any subject, or see the branches that are ready.

Kinetics: Newton's second law

Newton’s second law in kinetics: relating net force to mass and acceleration, component form (rectilinear and normal–tangential), D’Alembert’s principle, inertial vs non-inertial frames, and solving standard particle dynamics problems.

Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.

Why it matters

Engineers predict how machines, vehicles, structures under moving loads, and robotic arms will move when forces act on them. Newton’s second law turns a physical situation (forces) into equations for motion (accelerations, velocities, displacements), so you can size motors, design brakes, and check safety.

Key ideas

  • Inertia: The natural tendency of a body to resist change in its state of rest or uniform straight-line motion.
  • Force (F): An interaction that can change a body’s motion. SI unit: newton (N). One newton is the force that gives a 1 kg mass an acceleration of 1 m/s².
  • Acceleration (a): Rate of change of velocity with time. SI unit: m/s².
  • Inertial frame: A reference frame where a free particle moves with constant velocity unless acted on by a force. Earth-fixed frames are approximately inertial for most engineering problems.

Exact statement of Newton’s second law (vector form):

  • “The time rate of change of linear momentum of a particle is equal to the net external force acting on it, and this change takes place in the direction of the net force.” Mathematically: ΣF = dP/dt, where P = m v.
  • For constant mass: ΣF = m a.

Assumptions behind ΣF = m a for a particle:

  1. Mass is constant during the motion. 2) We are using an inertial frame of reference. 3) All relevant external forces are included (contact forces like normal reaction and friction; body forces like weight; applied forces like tension, thrust, spring force). 4) The particle model is valid (rotations and size effects negligible).

Derivation from first principles (momentum form to F = m a):

  1. Start with P = m v.
  2. Take time derivative: dP/dt = m dv/dt + v dm/dt.
  3. If mass is constant (dm/dt = 0), then dP/dt = m a.
  4. By Newton’s second law, ΣF = dP/dt, so ΣF = m a.

Component forms and common coordinate choices:

  • Rectangular components (x, y, z): Useful for rectilinear motion or when forces are naturally along axes (e.g., horizontal–vertical). Resolve forces and acceleration into components and apply ΣFx = m ax, ΣFy = m ay, ΣFz = m az.
  • Normal–tangential components (n–t): Useful for curvilinear motion along a known path. Tangential direction (t) is along the velocity; normal direction (n) points toward the center of curvature.
    • a_t = dv/dt (changes speed), from tangential force component.
    • a_n = v²/ρ (changes direction), toward center of curvature with radius of curvature ρ.
    • Equations: ΣF_t = m a_t, ΣF_n = m a_n = m v²/ρ.

Weight and gravity:

  • Weight (W): The gravitational force on a mass near Earth’s surface. W = m g, acting vertically downward. Standard magnitude of g ≈ 9.81 m/s² near sea level.

Free-body diagram (FBD) reminder (from the Equilibrium and free-body diagrams topic):

  • Isolate the particle. Show all external forces with correct directions and labels (weight W = m g, normal reaction N, friction f, tension T, applied forces). Choose and mark coordinate axes. Indicate known angles or geometry.

D’Alembert’s principle (dynamic equilibrium method):

  • Statement: “For a particle of mass m undergoing acceleration a, the vector sum of external forces and the inertia force (−m a) is zero.” That is, ΣF − m a = 0. This allows us to treat a dynamics problem like a statics problem by adding the fictitious inertia force −m a to the FBD and applying equilibrium of forces in chosen directions.
  • Assumptions: Same as Newton’s second law (inertial frame, constant mass). The inertia force is not a real external force; it is a bookkeeping device that must be equal to m a in magnitude and opposite in direction to the actual acceleration.
  • Typical use: Pulley–string systems, sliding blocks with friction, connected bodies, where solving simultaneous equations is easier with equilibrium-like sums.

Non-inertial frames (brief note):

  • If you analyze motion in a uniformly accelerating or rotating frame (e.g., elevator accelerating upward, or a turntable), additional fictitious forces appear (e.g., “apparent weight change” in an accelerating lift, centrifugal and Coriolis forces in rotating frames). This topic typically focuses on inertial frames. If you must use a non-inertial frame, include the appropriate fictitious force terms; otherwise stay in an inertial frame and apply ΣF = m a. In a linearly accelerating frame with acceleration a_frame, include a fictitious force −m a_frame on each mass; in a uniformly rotating frame with angular velocity Ω, include centrifugal −m Ω×(Ω×r) and Coriolis −2 m Ω×v_rel.

What to draw for common exam diagrams:

  1. Block on a rough horizontal surface pulled by a force at angle θ: Draw a rectangle for the block. Forces: weight W downward; normal N upward; applied force P at angle θ above horizontal; friction f opposite the motion along surface. Axes: x horizontal, y vertical. Label all given values and θ.
  2. Two blocks connected by a light inextensible string over a smooth (frictionless, massless) pulley (Atwood’s machine): Draw two blocks m1 and m2 on either side of a pulley with a string. Tension T is the same on both sides. Show assumed directions: heavier mass moves down, lighter moves up. For each block, draw its FBD separately: weight m g downward, tension T upward. Mark a as the magnitude of acceleration along the string.
  3. Particle moving along a curve: Draw the path with a point for the particle. At the point, draw unit directions: tangential t̂ along motion and normal n̂ toward center of curvature. Show forces resolved into t and n components. Label v, ρ, a_t, a_n.

Connections to other topics (for awareness only):

  • Work–energy principle, Impulse and momentum, and Collision of elastic bodies offer alternative solution methods. In this topic, we use ΣF = m a directly to write differential or algebraic equations of motion.

Formulas

ΣF = dP/dt — Sum of external forces equals time rate of change of linear momentum P. P is momentum (kg·m/s). Applies generally; for variable-mass systems (e.g., rockets), apply to a closed system or include momentum flux/thrust terms when mass crosses the system boundary.

ΣF = m·a — Net force equals mass times acceleration. m: kg; a: m/s²; F: N. Applies in an inertial frame with constant mass.

ΣF_x = m·a_x — x-component of Newton’s second law. Use when resolving along x-axis.

ΣF_y = m·a_y — y-component of Newton’s second law. Use when resolving along y-axis.

a_t = dv/dt — Tangential acceleration equals time rate of change of speed v. Units: m/s². Use along path tangential direction.

a_n = v²/ρ — Normal (centripetal) acceleration toward center of curvature. v: m/s; ρ: m. Units: m/s². Use along normal direction for curvilinear motion.

ΣF_t = m·a_t — Tangential component of Newton’s second law. Use to relate tangential force to change in speed.

ΣF_n = m·a_n = m·v²/ρ — Normal component of Newton’s second law. Use to relate radial force balance to path curvature.

W = m·g — Weight equals mass times gravitational acceleration. W: N; m: kg; g: 9.81 m/s² (standard near Earth surface). Direction: vertically downward.

T = m·(v²/ρ) (for pure circular motion with only tension providing centripetal force) — Tension needed for centripetal acceleration when other radial forces are absent. T: N; m: kg; v: m/s; ρ: m. Applies if the only inward force is the string tension.

ΣF − m·a = 0 — D’Alembert’s principle (dynamic equilibrium). Use as a statics-like equation by adding inertia force −m a on the FBD.

Worked examples

Example 1: Block on a rough horizontal surface pulled by an inclined force Given: Mass m = 10.0 kg on a horizontal surface. Coefficient of kinetic friction μk = 0.20. A force P = 50.0 N is applied at angle θ = 30.0° above the horizontal, pulling the block to the right. Take g = 9.81 m/s². Find the acceleration a of the block.

Steps:

  1. Draw FBD: Forces are weight W = m g downward; normal N upward; applied force P with horizontal component P cosθ to the right and vertical component P sinθ upward; kinetic friction f = μk N to the left (opposing motion).
  2. Choose axes: x to the right, y upward.
  3. Write y-direction equilibrium (no vertical acceleration): ΣFy = 0 ⇒ N + P sinθ − W = 0 ⇒ N = W − P sinθ.
  4. Compute N: W = m g = 10.0 × 9.81 = 98.1 N. P sinθ = 50.0 × sin30.0° = 50.0 × 0.5 = 25.0 N. So N = 98.1 − 25.0 = 73.1 N.
  5. Friction force: f = μk N = 0.20 × 73.1 = 14.62 N (opposes motion).
  6. x-direction dynamics: ΣFx = m ax ⇒ P cosθ − f = m a.
  7. Compute P cosθ: 50.0 × cos30.0° = 50.0 × 0.8660 ≈ 43.30 N.
  8. Solve for a: a = (P cosθ − f)/m = (43.30 − 14.62)/10.0 = 28.68/10.0 = 2.868 m/s².

Answer: The acceleration of the block is approximately 2.87 m/s² to the right. (Final: a = 2.87 m/s²)

Example 2: Two masses connected over a smooth pulley (Atwood’s machine) Given: Two blocks m1 = 4.00 kg and m2 = 6.00 kg are connected by a light inextensible string over a smooth, massless pulley. Find the acceleration a of the blocks and the tension T in the string. Take g = 9.81 m/s². Assume m2 > m1, so m2 moves downward and m1 moves upward.

Steps:

  1. Draw separate FBDs:
    • For m1 (going up): T upward, W1 = m1 g downward.
    • For m2 (going down): T upward, W2 = m2 g downward.
  2. Write Newton’s second law along the string direction (choose upward positive for m1 and downward positive for m2 so both accelerations are +a in their chosen directions):
    • For m1: ΣF = m1 a ⇒ T − m1 g = m1 a. (Eq. 1)
    • For m2: ΣF = m2 a ⇒ m2 g − T = m2 a. (Eq. 2)
  3. Add Eqs. 1 and 2 to eliminate T: (T − m1 g) + (m2 g − T) = m1 a + m2 a ⇒ (m2 − m1) g = (m1 + m2) a.
  4. Solve for a: a = [(m2 − m1)/(m1 + m2)] g = [(6.00 − 4.00)/(4.00 + 6.00)] × 9.81 = (2.00/10.00) × 9.81 = 1.962 m/s².
  5. Solve for T using Eq. 1: T = m1 g + m1 a = 4.00 × 9.81 + 4.00 × 1.962 = 39.24 + 7.848 = 47.088 N. (Check with Eq. 2: T = m2 g − m2 a = 6.00 × 9.81 − 6.00 × 1.962 = 58.86 − 11.772 = 47.088 N — consistent.)

Answer: Acceleration magnitude a = 1.962 m/s² (m2 downward, m1 upward), tension T = 47.09 N. (Final: a = 1.962 m/s²; T = 47.09 N)

Example 3: Particle in horizontal circular motion on a string Given: A 0.500 kg particle is whirled in a horizontal circle of radius 1.50 m at steady speed v = 4.00 m/s. The string is horizontal and provides the necessary centripetal force. Find the tension T in the string.

Steps:

  1. FBD: Forces on the particle in the horizontal plane: inward tension T toward the circle center. (Assume vertical forces are balanced by a support arrangement so that vertical motion is negligible; we consider only horizontal dynamics for centripetal acceleration.)
  2. Use normal component: ΣF_n = m v²/ρ.
  3. Here, ΣF_n = T inward, ρ = 1.50 m, m = 0.500 kg, v = 4.00 m/s.
  4. Compute: T = m v²/ρ = 0.500 × (4.00)² / 1.50 = 0.500 × 16.00 / 1.50 = 8.00 / 1.50 = 5.333… N.

Answer: The string tension is 5.33 N directed toward the center. (Final: T = 5.33 N)

Note: If gravity must be included (string not perfectly horizontal), resolve forces into vertical and horizontal components and use ΣFy = 0 (for steady height) and ΣF_n = m v²/ρ to solve for tension magnitude and angle.

Common mistakes

  • Using g = 10 m/s² without being told; unless the question allows it, use g = 9.81 m/s².
  • Resolving forces incorrectly: wrong sine/cosine with angle definitions; not aligning axes with given angles.
  • Sign errors in component equations (e.g., taking friction in the wrong direction, or assigning the same positive direction to connected bodies inconsistently).
  • Assuming tension is the same everywhere when the pulley has friction or mass; equality of tension requires a light, inextensible string and a smooth, massless pulley.
  • Applying ΣF = 0 in dynamics problems; remember ΣF = m a unless the acceleration component in that direction is zero.
  • Confusing a_t and a_n in curvilinear motion; a_t changes speed (dv/dt), a_n = v²/ρ changes direction toward the center.
  • Treating the inertia force −m a as a real force; it is only a computational tool in D’Alembert’s method.

For your exam

This topic commonly gives:

  • Definitions and statements: Newton’s laws, inertia, mass, particle, inertial frame, weight, D’Alembert’s principle. A full-marks answer gives the exact statement, the mathematical form, assumptions (inertial frame, constant mass), and a neat labeled sketch if relevant.
  • Short notes: Component form (x–y and n–t), when to use each; relation to momentum form ΣF = dP/dt; brief note on non-inertial frames and fictitious forces (without deep derivations).
  • Derivations: From ΣF = dP/dt to ΣF = m a for constant mass; expressions for tangential and normal accelerations; D’Alembert’s principle from ΣF = m a.
  • Numericals: Pulley–string systems (Atwood’s machine, blocks on inclines connected by strings), blocks with friction and applied forces, motion along circular paths (centripetal force), elevator apparent weight. Full-marks solutions include: FBDs for each body, chosen axes, equations before substituting numbers, units throughout, correct significant figures, and a boxed/clearly stated final answer with units and direction.
  • Diagrams: What to draw and label as described above (forces, angles, axes, directions of assumed motion/acceleration).

Tips for full marks:

  • Start with a clean FBD and define positive directions. State “Taking right/upward/tangential as positive.”
  • Write ΣF equations symbolically first; then substitute numbers with units.
  • State the result with magnitude, direction, and units. Check reasonableness (e.g., heavier mass goes down; friction reduces acceleration; centripetal force points inward).

Quick check

  1. State Newton’s second law for a particle and give its mathematical form for constant mass.
  2. A particle moves along a curve with speed v. What are a_t and a_n in terms of v and ρ?
  3. Two masses 3 kg and 7 kg hang over a smooth pulley. Find their acceleration magnitude. Take g = 9.81 m/s².

Answers: 1) The time rate of change of linear momentum equals the net external force; for constant mass: ΣF = m a. 2) a_t = dv/dt, a_n = v²/ρ toward the center of curvature. 3) a = [(7 − 3)/(7 + 3)] × 9.81 = (4/10) × 9.81 = 3.924 m/s².

Finished this topic? Mark it so your progress, study plan and readiness keep up.

Stuck on something here?