Friction and belt friction
Basics of dry friction and belt (capstan) friction, including laws, angle of friction, angle of repose, cone of friction, capstan equation for flat and V-belts, and related calculations.
Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.
Why it matters
Key ideas
- Static friction (Fs): Friction present when there is no relative motion. It adjusts up to a maximum value called limiting friction.
- Limiting friction (Fmax): The maximum possible static friction just before motion begins. Law:
Fmax = μs·N, whereμsis the coefficient of static friction. - Kinetic (sliding) friction (Fk): Friction during relative motion. Law:
Fk = μk·N, withμk ≤ μs. - Coefficient of friction (μ): A dimensionless constant that depends on the pair of surfaces and their condition. Separate values are used for static (μs) and kinetic (μk) friction.
- Angle of friction (φ): The angle between the resultant reaction and the normal reaction at limiting equilibrium. Exact statement: At the onset of sliding,
tan φ = μs. Assumptions: rigid bodies, dry surfaces, friction proportional to normal reaction, and independent of apparent area for given N. - Angle of repose (θr): The maximum angle of an inclined plane at which a body at rest is on the point of sliding down due to its own weight. Exact result: For impending motion down the plane,
tan θr = μs. Hence,θr = φ. - Cone of friction: For a 3D contact with all possible directions of impending motion, the locus of resultant reactions at limiting equilibrium forms a right circular cone with semi-vertical angle
φ(angle of friction). If the resultant lies inside the cone, no motion occurs; on the surface, impending motion; outside, motion occurs.
Derivations commonly asked
- Angle of friction relation
tan φ = μ
- Consider a block at limiting equilibrium on a rough horizontal plane under a horizontal force P. Friction acts opposite to P with magnitude
Fmax = μs·N. Resultant reaction R is vector sum of N and Fmax. Sotan φ = Fmax / N = μs.
Diagram to draw: A block on a horizontal plane. Show N upward, W downward (weight), P to the right, friction F to the left at contact. Show resultant R making angle φ with the normal.
- Angle of repose equals angle of friction
- Block of weight W on a rough inclined plane at angle θ with horizontal. For impending motion downwards:
- Components of W: along plane
W sin θ, normal to planeW cos θ. - Normal reaction
N = W cos θ. - Limiting friction
Fmax = μs N = μs W cos θacts up the plane. - Equilibrium along plane at impending motion:
W sin θ = Fmax = μs W cos θ⇒tan θ = μs. - At limiting condition, θ = θr and
tan θr = μs. Alsotan φ = μs, henceθr = φ.
- Components of W: along plane
Diagram to draw: Inclined plane at angle θ, block on it. Show W vertically down, resolve into W sin θ along plane (downwards) and W cos θ normal to plane. Show N perpendicular to plane, friction up the plane at impending down-slope motion.
- Capstan (belt friction) equation for a flat belt/rope:
T1/T2 = e^(μθ)
- System: A flexible belt or rope on a fixed rough cylinder/pulley.
T1is the larger (tight) side tension,T2is the smaller (slack) side tension.θis the wrap/contact angle in radians. Assume: perfectly flexible, inextensible belt; uniform normal pressure; no belt mass or centrifugal effects; impending slip condition (limiting friction) everywhere in contact. - Consider an elemental belt segment subtending small angle dθ at the pulley center. Let belt tension at the start be T and at the end be
T + dT. Normal reaction on elementdNdirected radially. Friction force magnitudeμ dN, direction opposite to motion tendency, tangential. - Force balance on the element:
- Radial (normal) equilibrium:
dN = T dθ(using small-angle approximation, resultant of T at ends ≈ T dθ radially). Strictly, radial component sum ≈ T dθ when dθ is small. - Tangential (along belt) equilibrium at limiting friction:
dT = μ dN = μ T dθ.
- Radial (normal) equilibrium:
- Separate variables and integrate from slack to tight side:
∫(dT/T) = μ ∫ dθ⇒ln(T1/T2) = μ θ⇒T1/T2 = e^(μ θ).
Diagram to draw: Circle for pulley. Small belt element subtending dθ at contact. Show T at one end, T + dT at the other, dN pointing to pulley center, friction μ dN tangential opposite impending motion. Indicate wrap angle θ from entry to exit.
- V-belt (grooved pulley) modification
- When the belt runs in a V-groove of included groove angle β, the effective normal reaction increases. The capstan formula becomes
T1/T2 = e^(μ' θ)withμ' = μ / sin(β/2)under the same assumptions as above. This result comes from resolving forces on both sides of the groove; the net normal reaction is higher by the factor1/sin(β/2).
- Power transmitted by a belt (basic, ignoring belt mass and slip)
- Power P is force times velocity along the belt:
P = (T1 − T2) · v, where v is belt linear speed. Assumptions: steady state, no slip or negligible slip, belt mass neglected (so centrifugal effects ignored), flat belt unless otherwise stated.
- Centrifugal tension (at high belt speeds)
- If belt mass per unit length is m, the moving belt experiences centrifugal tension
Tcdue to rotation over the pulley. For steady circular motion along the pulley arc,Tc = m v²acting equally on tight and slack sides. This reduces the effective belt tensions available for friction/power by Tc. Common design relation for maximum power (with friction and pulley sized accordingly) is: Maximum power occurs whenTc = T/3, where T is the maximum permissible belt tension (due to strength). Thenv_max = √(T / (3 m)). Use these only when the problem states or implies centrifugal effects. In such cases, use the modified tension ratio: (T1 − Tc)/(T2 − Tc) = e^(μ θ).
Formulas
- Fmax: limiting static friction (N). μs: coefficient of static friction (dimensionless). N: normal reaction (N). Applies at the instant before motion starts. Also, 0 ≤ Fs ≤ μs·N; at impending motion, Fs = Fmax.
Fk = μk·N- Fk: kinetic (sliding) friction (N). μk: coefficient of kinetic friction (dimensionless). N: normal reaction (N). Applies during steady sliding.
tan φ = μs- φ: angle of friction (rad or deg). μs: coefficient of static friction (dimensionless). At limiting equilibrium.
tan θr = μs- θr: angle of repose (rad or deg). μs: coefficient of static friction (dimensionless). For a block on an inclined plane at impending motion.
T1/T2 = e^(μ θ)- T1: tight side tension (N). T2: slack side tension (N). μ: coefficient of friction (dimensionless). θ: wrap angle in radians. Flat belt/rope, impending slip, no belt mass/centrifugal effects.
T1/T2 = e^( (μ / sin(β/2)) · θ )- β: groove angle of V-belt pulley (rad or deg; use sin of half-angle). Others as above. For V-belts under impending slip.
P = (T1 − T2) · v- P: power (W). T1, T2: N. v: belt speed (m/s). For belt drives without significant slip/centrifugal effects.
v = π D n- v: belt speed (m/s). D: pulley diameter (m). n: pulley rotational speed (rev/s). For a belt on a pulley of diameter D rotating at n revolutions per second.
Tc = m v²- Tc: centrifugal tension per side (N). m: belt mass per unit length (kg/m). v: belt speed (m/s). For high-speed belts; acts on both sides.
v_max = √(T / (3 m))- v_max: belt speed for maximum power (m/s). T: maximum permissible belt tension (N). m: belt mass per unit length (kg/m). Applies when including centrifugal tension and the standard maximum power criterion.
Worked examples
Given: A rope is wrapped 2.5 turns around a fixed bollard. Coefficient of friction μ = 0.3. The load tension on the tight side is T1 = 8.0 kN. Find the minimum holding force T2 at the free end.
Steps:
- Data: Number of turns = 2.5 ⇒ wrap angle
θ = 2.5 · 2π = 5π rad ≈ 15.708 rad. μ = 0.3. T1 = 8.0 kN = 8000 N. - Formula:
T1/T2 = e^(μ θ)⇒T2 = T1 / e^(μ θ). - Substitute: Exponent
μ θ = 0.3 × 15.708 = 4.7124. Thene^(4.7124) ≈ 111.32(checked). - Compute:
T2 = 8000 N / 111.32 ≈ 71.9 N.
Answer: The minimum holding force is approximately 72 N (to two significant figures).
- Flat belt drive — tensions and power Given: A flat belt runs over a 0.50 m diameter pulley with angle of contact θ = 160°. Coefficient of friction μ = 0.28. Pulley speed = 600 rpm. Maximum belt tension (allowed by strength) T = 1000 N. Assume belt mass is negligible and no slip. Find (a) T1, T2, and (b) power transmitted.
Steps:
- Convert angle:
θ = 160° = 160 × (π/180) = 2.7925 rad. - Tension ratio:
T1/T2 = e^(μ θ) = e^(0.28 × 2.7925) = e^(0.7819) ≈ 2.185. - With negligible mass and given maximum tension limiting tight side, take
T1 = T = 1000 N. ThenT2 = T1 / 2.185 = 1000 / 2.185 = 457.9 N. - Belt speed:
v = π D n. HereD = 0.50 m,n = 600 rpm = 10 rps. Sov = π × 0.50 × 10 = 5π = 15.708 m/s. - Power:
P = (T1 − T2) v = (1000 − 457.9) N × 15.708 m/s = 542.1 × 15.708 = 8514 W.
Answers: (a) T1 ≈ 1000 N, T2 ≈ 458 N; (b) Power ≈ 8.51 kW.
- V-belt on a grooved pulley — required tight-side tension Given: A V-belt runs in a pulley with groove angle β = 40°. μ between belt and groove faces = 0.22. Angle of contact θ = 150° on the pulley. The slack-side tension T2 must be at least 300 N to avoid belt flutter. Find the required tight-side tension T1 for impending slip.
Steps:
- Convert:
β/2 = 20°, sosin(β/2) = sin 20° = 0.3420(checked). Effective frictionμ' = μ / sin(β/2) = 0.22 / 0.3420 = 0.643. - Convert θ:
θ = 150° = 150 × π/180 = 2.6180 rad. - Tension ratio:
T1/T2 = e^(μ' θ) = e^(0.643 × 2.6180) = e^(1.684) = 5.388. - Compute T1:
T1 = 5.388 × 300 N = 1616 N.
Answer: The required tight-side tension is approximately 1.62 kN.
Note: If the problem requires power, compute P = (T1 − T2) v using the belt speed.
Common mistakes
- Assuming
T1/T2 = e^(μ θ)during steady sliding. The standard derivation is for limiting (impending) slip; with actual slip, the relation is approximate and power loss occurs. - Taking the given maximum belt tension as the net tight-side tension without checking centrifugal effects when belt speeds are high. If m and speed are significant, reduce the available tight- and slack-side tensions by Tc.
- Forgetting that for V-belts the effective friction is
μ / sin(β/2), notμ × sin(β/2). - Reversing tight and slack sides or computing
T2/T1instead ofT1/T2. - Not carrying units and not checking reasonableness (e.g., a tiny holding force with many wraps is expected; the opposite suggests a mistake).
For your exam
- Derivations: Step-by-step derivation of
tan φ = μ; equality of angle of repose and angle of friction; capstan equationT1/T2 = e^(μ θ); V-belt modificationμ' = μ / sin(β/2)and resulting tension ratio. - Numericals: Typical problems include computing holding force on a rope with multiple turns; determining T1, T2, and power for a belt drive; V-belt tension ratio; including belt speed from pulley dimensions and rpm. Sometimes include centrifugal tension and maximum power speed; write assumptions clearly if you use them.
- Diagrams: Free-body diagrams of a block on a plane; the belt elemental segment on a pulley showing T, T + dT, dN, μ dN; V-groove contact with resolved normals. Label all forces and angles.
- Full-marks answers: Begin with a clean FBD, state assumptions, write governing equations symbolically before substituting numbers, keep units throughout, and present a boxed or bold final answer with appropriate significant figures.
Quick check
- The angle of friction is 20°. What is μs?
- A flat belt wraps 200° around a pulley, μ = 0.25. What is T1/T2? (Use radians.)
- A V-belt has β = 30°. If μ = 0.20, what is the effective μ' for tension ratio calculations?
Answers: 1) μs = tan 20° ≈ 0.364; 2) θ = 200° = 3.4907 rad ⇒ T1/T2 = e^(0.25 × 3.4907) = e^(0.8727) ≈ 2.39; 3) μ' = μ / sin(β/2) = 0.20 / sin 15° = 0.20 / 0.2588 ≈ 0.773.
Finished this topic? Mark it so your progress, study plan and readiness keep up.
Stuck on something here?