Analysis of trusses
Analysis of trusses: idealizations, determinacy and stability, zero‑force members, method of joints, method of sections, sign conventions, and solved numerical examples.
Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.
Why it matters
Engineers use trusses in bridges, roofs, towers, cranes, and transmission line masts because they provide high strength with low weight. Understanding how to analyze forces in truss members allows you to select safe member sizes, check failure modes, and estimate deflections in real designs.
Key ideas
- Tension and compression (sign convention): Take tensile member force as positive (+T, pulling the joint), compressive as negative (−C, pushing the joint). State your sign convention at the start and be consistent.
- Degree of static determinacy (planar truss): For a pin-jointed planar truss with m members, j joints, and r external reaction components, the condition for external and internal static determinacy is: m + r = 2·j. Commonly written as m = 2·j − r. If m > 2·j − r the truss is statically indeterminate; if m < 2·j − r the truss is unstable or has a mechanism (provided supports are adequate).
- External stability: The support reactions must be sufficient and non-collinear; otherwise, the whole truss can move as a rigid body regardless of member count.
- Zero-force members (ZFM): Quick rules at a joint (no external load, no support reaction at that joint):
- If two non-collinear members meet at an unloaded joint, both are zero-force members.
- If three members meet at a joint and two are collinear, then the third (non-collinear) is a zero-force member. These rules speed up analysis and are often asked in exams.
- Method of joints (MoJ): Solve member forces joint-by-joint using equilibrium of a particle: ΣFx = 0 and ΣFy = 0 at each joint. Start at a joint where at most two unknown member forces exist. Use geometry to resolve components. Proceed sequentially until all required member forces are found.
- Method of sections (MoS): Cut the truss by an imaginary “section” passing through no more than three unknown member forces, isolate one side of the cut, and use ΣFx = 0, ΣFy = 0, and ΣM(any point) = 0 to solve directly for the forces of interest. Choose the moment point to eliminate as many cut-force lines of action as possible.
- Geometric resolution: Resolve member forces into x- and y-components using direction cosines based on the member’s slope or using known angles (e.g., 30°, 45°, 60°). Always compute or state the angle used.
- Support reactions first: Before analyzing members, treat the truss as a rigid body to compute support reactions using overall equilibrium (ΣFx = 0, ΣFy = 0, ΣM = 0). This is the same skill as in “Support reactions of beams.”
- Diagrams required in exam answers:
- Overall truss free-body diagram (FBD): Draw the truss outline with all external loads and supports. Show support types (pin: Ax, Ay; roller: one reaction normal to support surface), and indicate distances (panel lengths, height).
- Joint FBDs: For a chosen joint, isolate it as a point with member forces drawn along member directions, pointing away from the joint if assuming tension. Label angles with respect to x-axis or show rise-run triangles with dimensions.
- Section cut: Draw the truss with a cutting line through the selected members (≤ 3 unknowns). Shade or circle the side kept for equilibrium. Draw the cut-member forces with assumed tension directions. Mark the moment center used (e.g., joint B) and show perpendicular distances if using scalar moments.
- Exact statements:
- Definition: “A plane truss is a structure consisting of straight, slender members connected at their ends by frictionless pins, all members lying in the same plane, and subjected only to loads and reactions at the joints, so that members carry only axial force.”
- Determinacy condition (planar truss): “A pin-jointed truss in a plane is statically determinate and stable when m + r = 2·j and the truss is externally stable.” Assumptions: ideal pins, loads at joints, no member redundancy, no external instability.
- Zero-force member rules: Stated above with the no external load/reaction at that joint assumption.
Derivations often asked:
- Derivation of m = 2·j − r (planar truss): Each joint in a plane provides two independent equilibrium equations, ΣFx = 0 and ΣFy = 0, so across j joints there are 2j scalar equations. Unknowns are m internal member forces plus r external reactions, total m + r. For a statically determinate truss, the number of independent equations equals the number of unknowns: m + r = 2j, provided the equations are independent (no mechanism) and supports ensure external stability. If the structure is assembled from a basic triangle and then members are added by adding two members and one joint at a time (simple truss), this condition naturally holds.
Formulas
ΣFy = 0— Sum of vertical components of all forces equals zero; planar equilibrium. Units: N.ΣM_O = 0— Sum of moments of all forces about point O equals zero; planar equilibrium. Moment unit: newton·metre (N·m). Choose O to simplify calculations.m + r = 2·j— Planar pin-jointed truss determinacy condition. m: number of members (dimensionless), r: number of reaction components (dimensionless), j: number of joints (dimensionless).F_member = T (tension) or C (compression)with resolution:Fx = F·cosθ,Fy = F·sinθ— θ is the angle of the member with the positive x-axis; SI unit of F: N.- Direction cosines from geometry:
cosθ = Δx/L,sinθ = Δy/L,L = √(Δx² + Δy²)— Δx, Δy in metre (m), L in metre (m), θ in degrees or radians. - Zero-force member rules: If an unloaded joint has only two non-collinear members, both forces are zero. If an unloaded joint has three members with two collinear, the non-collinear member’s force is zero. Applies only when no external load or support reaction at that joint.
- Sign convention: “Tension positive”: If the computed F is positive, the member is in tension; if negative, it is in compression. State this before solving.
Worked examples
Example 1 — Method of joints on a simple triangular truss Given: A plane truss is a single triangle with joints A(0, 0), B(3, 3), C(6, 0). Supports: pin at A, roller at C. A concentrated load P = 12 kN acts downward at joint B. Members: AB, BC (inclined), AC (horizontal base). Use tension-positive sign convention.
Support reactions (overall FBD):
- ΣFy = 0: Ay + Cy − 12 = 0. By symmetry (load at midspan B), Ay = Cy = 6 kN upward.
- ΣFx = 0: Ax = 0 (no horizontal external loads).
Geometry and direction cosines:
- AB: Δx = +3 m, Δy = +3 m, length L = √(3² + 3²) = 4.243 m. cosθ = 3/4.243 = 0.7071, sinθ = 0.7071.
- BC: Δx = +3 m, Δy = −3 m from B to C: cosθ = +0.7071, sinθ = −0.7071 (same length).
- AC is horizontal: sinθ = 0, cosθ = 1.
Joint B equilibrium (unknowns FAB, FBC): Assume both tensions away from joint.
- ΣFx = 0: (−0.7071)·FAB + (0.7071)·FBC = 0 ⇒ FAB = FBC.
- ΣFy = 0: (−0.7071)·FAB + (−0.7071)·FBC − 12 = 0. Substitute FAB = FBC: (−0.7071)(FAB + FBC) − 12 = 0 ⇒ −1.4142·FAB − 12 = 0 ⇒ FAB = −8.485 kN. Then FBC = −8.485 kN. Interpretation: FAB = FBC = −8.485 kN → both members AB and BC are in compression of 8.485 kN.
Joint A equilibrium (find FAC): Unknowns FAB (already found), FAC. Take forces away from joint as positive tension. With FAB = −8.485 kN (compression), the assumed tensile direction at A gives a negative value.
- ΣFy = 0: Ay + FAB·0.7071 = 0 ⇒ 6 + (−8.485)(0.7071) = 0 (satisfied).
- ΣFx = 0: Ax + FAB·0.7071 + FAC·1 = 0 ⇒ 0 + (−8.485)(0.7071) + FAC = 0 ⇒ FAC = +6.000 kN (tension) along AC.
Results:
- FAB = 8.485 kN compression
- FBC = 8.485 kN compression
- FAC = 6.000 kN tension Final answers: FAB = 8.485 kN (C), FBC = 8.485 kN (C), FAC = 6.000 kN (T).
Check at joint C: Cy = 6 kN up balances vertical of BC: FBC·sin(−45°) = (8.485)(−0.7071) = −6 kN; horizontal of BC (6 kN to right) is balanced by AC tension 6 kN to left at C. All consistent.
Example 2 — Method of sections on a 2-panel Warren truss; zero-force member appears Given: Joints (m): A(0, 0), B(3, 0), C(6, 0) on bottom chord; D(1.5, 2.598), E(4.5, 2.598) on top chord (equilateral geometry with panel length 3 m, height = 3·√3/2 = 2.598 m). Members: bottom AB, BC; top DE; diagonals AD, DB, BE, EC. Supports: pin at A, roller at C. Load: vertical downward 10 kN at joint D.
Support reactions (overall FBD):
- ΣM_A = 0: Cy·6 − 10·1.5 = 0 ⇒ Cy = 2.5 kN upward.
- ΣFy = 0: Ay + Cy − 10 = 0 ⇒ Ay = 7.5 kN upward.
- ΣFx = 0: Ax = 0 (no horizontal external loads).
Members of interest: Use a section cutting through members BE, EC, and BC (≤ 3 unknowns). Keep the right-hand side (joints E and C). Mark assumed tension directions on cut members.
Geometry of diagonals (lengths ≈ 3.000 m):
- For member EC from C to E: Δx = −1.5 m, Δy = +2.598 m ⇒ unit vector u_EC = (−0.5, +0.866).
- For member BE from E to B: Δx = −1.5 m, Δy = −2.598 m ⇒ unit u_BE = (−0.5, −0.866).
- Member BC is horizontal (B to C): unit u_BC = (−1, 0) when pointing from C to B.
Moment about B to get F_EC directly (right-hand section): Only RCy at C and the cut force in EC produce moment about B (forces in BC and BE pass through B).
- Take counterclockwise positive. Position vector from B to C: r_BC = (3, 0) m.
- RCy at C = +2.5 kN upward ⇒ moment about B: M_RCy = 3·2.5 = +7.5 kN·m.
- Let T_EC be tension in EC acting from C towards E (unknown). Applying at C: F_EC = T_EC·(−0.5 i + 0.866 j). Moment about B is r × F: (3,0) × (−0.5 T_EC, 0.866 T_EC) = 3·0.866·T_EC = +2.598·T_EC kN·m.
- ΣM_B = 0 ⇒ 7.5 + 2.598·T_EC = 0 ⇒ T_EC = −2.886 kN. Interpretation: Negative means member EC is in compression of 2.886 kN (opposite to assumed tension direction).
Solve for T_BE and T_BC using force equilibrium of the right-hand section:
- ΣFx = 0: (−0.5)·T_BE + (−0.5)·T_EC + (−1)·T_BC + 0 = 0.
- ΣFy = 0: (−0.866)·T_BE + (0.866)·T_EC + 2.5 = 0. Substitute T_EC = −2.886 kN:
- ΣFy: −0.866·T_BE + 0.866·(−2.886) + 2.5 = 0 ⇒ −0.866·T_BE − 2.500 + 2.5 = 0 ⇒ T_BE = 0 kN.
- ΣFx: −0.5·0 + (−0.5)(−2.886) − T_BC = 0 ⇒ 1.443 − T_BC = 0 ⇒ T_BC = 1.443 kN (tension).
Results for cut members:
- Member EC: 2.886 kN compression
- Member BE: 0 kN (zero-force member under this loading)
- Member BC: 1.443 kN tension
Observations: The zero-force member arises naturally from equilibrium. In many Warren/Pratt trusses, diagonals away from the loaded region can be zero under specific symmetric loadings.
Units check: All forces in kN; moments in kN·m; geometry exact values use √3 ≈ 1.732 (height 2.598 m); diagonal length ≈ 3.000 m from chosen geometry.
Common mistakes
- Using wrong angles or slopes for members; not computing direction cosines from Δx, Δy; or swapping sin and cos.
- Cutting more than three unknown member forces in method of sections (planar case): you only have three independent equilibrium equations.
- Applying zero-force member rules at a joint that actually has an external load or reaction; the rules then do not apply.
- Rounding too early: keep at least 3–4 significant figures in intermediate steps to avoid cancellation errors.
- Forgetting that roller supports have only one reaction along the normal to the surface (usually vertical); pin supports have two components (Ax, Ay).
For your exam
- Derivations: m = 2·j − r for planar truss; proofs/justifications of zero-force member rules from joint equilibrium.
- Diagrams: full truss FBD with supports and loads; joint FBD; section cut diagram with labeled members and chosen moment center.
- Numericals: compute support reactions; find forces in specific members using method of joints or method of sections; identify zero-force members before solving; mixed problems with multiple loads.
- What a full-marks answer includes:
- Clear statement of assumptions (plane truss, loads at joints, tension positive).
- Neat, labeled diagrams with all distances and angles or rise–run triangles.
- Correct support reactions using overall equilibrium.
- Step-by-step equations: write formulas before substituting numbers; carry SI units; indicate sign of each result and interpret as T or C.
- Brief concluding statement summarizing member forces and nature (T/C).
Quick check
- State the condition for a planar truss to be statically determinate in terms of m, j, and r.
- At an unloaded joint, two non-collinear members meet. What are their forces?
- In method of sections, why is it advantageous to take moments about a joint that lies on two of the cut members?
Answers: 1) m + r = 2·j (with external stability). 2) Both are zero-force members. 3) Because their lines of action pass through the moment center, they contribute zero moment, eliminating those unknowns so the remaining one can be solved directly.
Finished this topic? Mark it so your progress, study plan and readiness keep up.
Stuck on something here?