Velocity and acceleration analysis of mechanisms

Planar velocity and acceleration analysis of mechanisms (four-bars, slider-cranks, and sliders in rotating links) using relative motion, instantaneous centers, loop-closure differentiation, and Coriolis acceleration.

Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.

Why it matters

Velocity and acceleration analysis turns a mechanism’s geometry and input motion into outputs like piston speed, follower jerk, and bearing loads. It is essential for engine kinematics, cam/gear dynamics, quick-return mechanisms, and for estimating inertial forces used later in Dynamic Analysis of Mechanisms, Governors, and Vibrations.

Key ideas

  • Assumptions for this topic (planar kinematics unless stated):

    • Links are rigid; joints are ideal pin/slider joints with negligible clearance and friction.
    • Motion is confined to a plane; angular quantities point along the out-of-plane z-axis.
    • Known input(s): a link angle vs time, or angular velocity/acceleration at an instant. Forces are not considered here (see Kinetics of Rigid Bodies and Dynamic Analysis of Mechanisms).
  • Sign conventions and vectors:

    • Take x–y in the plane, z out of plane. Positive angular velocity ω and angular acceleration α are counterclockwise (CCW, +z).
    • For a position vector r from A to B (r_BA), the planar cross product is ω × r = ω k × (x i + y j) = ω(−y i + x j).
    • Use unit vectors u_r (along a link/slot; radial only if the link/slot is radial from a center) and u_t (tangential, 90° CCW from u_r) when helpful; u_t = k × u_r.
  • Rigid-body relative velocity (same rigid link):

    • For two points A and B on the same rigid body with angular velocity ω: v_B = v_A + ω × r_BA. Direction of v_B relative to v_A is perpendicular to r_BA.
    • Magnitude form for rotation about fixed O: v_P = ω r, direction perpendicular to OP.
  • Rigid-body relative acceleration (same rigid link):

    • a_B = a_A + α × r_BA − ω² r_BA. The −ω² r_BA term is the normal (centripetal) component toward the center of rotation at that instant; α × r_BA is tangential.
  • Slider on a rotating link (Coriolis acceleration):

    • If a point P slides along a slot in a link that rotates with angular velocity ω and angular acceleration α, the absolute acceleration is a_P = a_rot + a_rel + a_cor, where:
      • a_rot = α × r − ω² r (due to rotation of the link at radius r = OP),
      • a_rel is the relative (along-slot) acceleration of P w.r.t. the link, directed along the slot,
      • a_cor is the Coriolis acceleration, magnitude 2 ω v_rel, direction perpendicular to the slot in the sense of rotation (90° ahead for CCW). This arises from time variation of the moving unit vectors in the rotating frame.
  • Instantaneous center of rotation (IC) method for velocities:

    • Statement: At any instant, the planar motion of a rigid link is equivalent to a pure rotation about its instantaneous center (IC). The velocity of any point is perpendicular to the line joining it to the IC with magnitude ω × distance to IC.
    • Kennedy’s theorem (Three centers in line): For three bodies in plane motion, the three instantaneous centers corresponding to the three pairs lie on a straight line. This is heavily tested for locating ICs in four-bars and slider-cranks.
    • IC method is only for velocity analysis (not acceleration) and is graphical/geometric.
  • Velocity and acceleration polygons (graphical):

    • For a given mechanism configuration, construct velocity polygons using known directions (perpendicular to links or along slider paths). Acceleration polygons use both normal (toward joint along link) and tangential (perpendicular to link) components. Good for exam sketches; accuracy depends on scale and drawing quality.
  • Analytical (loop-closure) method (recommended for numericals and GATE):

    • Write the vector loop for a closed chain (e.g., four-bar): r_1 + r_2 + r_3 + r_4 = 0 with appropriate directions. Using complex numbers: r_i e^{jθ_i}.
    • Differentiate once to get velocities: j r_2 ω_2 e^{jθ_2} + j r_3 ω_3 e^{jθ_3} + j r_4 ω_4 e^{jθ_4} = 0. Separate real/imag to solve for unknown angular velocities.
    • Differentiate again for accelerations: −r_2 ω_2² e^{jθ_2} + j r_2 α_2 e^{jθ_2} + … = 0. Solve for angular accelerations. For slider joints, constrain components along/normal to slider direction.
    • Advantages: precise, works for both velocity and acceleration; extensible to general planar mechanisms.
  • Slider-crank kinematics (standard geometry at an instant):

    • Let OA = r be the crank at angle θ from line of stroke (x-axis), AB = l the connecting rod making angle β with the line of stroke; then sin β = (r/l) sin θ.
    • Approximations for long connecting rod (l ≫ r): β is small, so sin β ≈ β ≈ (r/l) sin θ and cos β ≈ 1.
    • Useful instant relations (exact at an instant using relative velocity decomposition):
      • v_A = ω_1 r, perpendicular to OA,
      • ω_2 (connecting rod’s angular velocity) and slider velocity v_B follow from resolving v_A = v_B + v_A/B with v_B along line of stroke and v_A/B perpendicular to AB.
    • Standard limiting cases (asked conceptually):
      • At inner/outer dead center (θ = 0° or 180°), slider velocity is zero; connecting rod angular velocity is finite (nonzero if crank speed ≠ 0) and its direction switches across dead center.
      • For l → ∞, slider velocity reduces to v_B ≈ ω_1 r sin θ and slider acceleration a_B ≈ ω_1² r cos θ.
  • Why real devices differ from the ideal:

    • Joint clearances and link flexibility shift IC locations and introduce small additional velocity components and higher harmonics in acceleration (affecting Vibrations and Cam Dynamics).
    • Friction in sliders and pins retards sliding motion (not modeled here), changing actual time histories vs the ideal kinematic prediction.

Formulas

v_B = v_A + ω × r_BA

  • v_B, v_A: linear velocities of points B and A (m/s). ω: angular velocity of the rigid body (rad/s, +CCW). r_BA: position vector from A to B (m). Planar rigid-body kinematics at an instant.

a_B = a_A + α × r_BA − ω² r_BA

  • a_B, a_A: linear accelerations (m/s²). α: angular acceleration (+CCW, rad/s²). ω: angular velocity (rad/s). r_BA: position vector from A to B (m). Planar rigid-body acceleration at an instant.

v_P = ω r

  • v_P: speed of a point at distance r from a fixed rotation center (m/s). ω: angular velocity (rad/s). r: radius (m). Applies when the body rotates about a fixed point O.

a_P = α × r − ω² r

  • a_P: acceleration of a point at radius r on a body rotating about a fixed point (m/s²). α: angular acceleration (rad/s²). ω: angular velocity (rad/s). r: radius (m). Tangential plus normal components.

a_cor = 2 ω v_rel

  • a_cor: magnitude of Coriolis acceleration (m/s²). ω: angular velocity of the link carrying the slot (rad/s). v_rel: relative sliding speed along the slot (m/s). Direction is 90° ahead of the slot in the sense of ω (perpendicular to v_rel). Applies to a slider on a rotating link.

sin β = (r/l) sin θ

  • β: angle of connecting rod with line of stroke (rad or deg). r: crank radius (m). l: connecting rod length (m). θ: crank angle from line of stroke (rad or deg). Slider-crank geometry (instantaneous configuration).

v_B = −ω_1 r sin θ + ω_1 r cos θ tan β

  • v_B: slider velocity along line of stroke (m/s; sign per chosen +x). ω_1: crank angular velocity (rad/s). r: crank radius (m). θ: crank angle (rad). β from sin β relation above. Exact instantaneous relation from relative velocity resolution.

ω_rod = (ω_1 r cos θ) / (l cos β)

  • ω_rod: angular velocity of the connecting rod (rad/s, +CCW). ω_1: crank angular velocity (rad/s). r: crank radius (m). θ: crank angle (rad). l: connecting rod length (m). β as above. Slider-crank at an instant.

N_IC = n (n − 1) / 2

  • N_IC: number of instantaneous centers among n links (including ground). n: number of links (dimensionless). Planar mechanisms; used with Kennedy’s theorem to locate ICs.

r_2 e^{jθ2} + r_3 e^{jθ3} + r_4 e^{jθ4} + … = 0

  • Complex loop-closure for a closed kinematic chain. r_i: link lengths (m). θ_i: link angles (rad). Applies to position analysis; differentiate for velocities/accelerations.

j r_2 ω_2 e^{jθ2} + j r_3 ω_3 e^{jθ3} + j r_4 ω_4 e^{jθ4} + … = 0

  • Velocity-loop from differentiating the position loop once. ω_i: angular velocities (rad/s). Solve real/imag parts.

−r_2 ω_2² e^{jθ2} + j r_2 α_2 e^{jθ2} + −r_3 ω_3² e^{jθ3} + j r_3 α_3 e^{jθ3} + … = 0

  • Acceleration-loop from differentiating the velocity loop. α_i: angular accelerations (rad/s²).

a_P = (−ω² r + a_rel) u_r + (α r + 2 ω v_rel) u_t

  • a_P: absolute acceleration of a slider P on a rotating radial slot (m/s²). ω, α: angular velocity/acceleration of the link (rad/s, rad/s²). r: instantaneous radius OP (m). v_rel, a_rel: relative sliding speed/acceleration along the slot (m/s, m/s²). u_r: along slot (radial); u_t: tangential (perpendicular, CCW). Planar slider on a rotating radial arm.

v_P = v_rel u_r + ω r u_t

  • v_P: absolute velocity of the slider (m/s). v_rel: relative sliding speed along a rotating radial slot (m/s). ω r: tangential speed (m/s). u_r, u_t as above.

Worked examples

Example 1 — Slider-crank velocities by relative velocity (direct) Given: Crank radius r = 0.05 m, connecting rod length l = 0.20 m, crank angular velocity ω_1 = 100 rad/s CCW, crank angle θ = 60° from line of stroke (x-axis). Find (i) slider velocity v_B (sign: +x to the right), (ii) connecting rod angular velocity ω_rod (CCW positive).

Steps:

  1. Geometry: sin β = (r/l) sin θ.

    • Numbers: (r/l) = 0.05/0.20 = 0.25; sin θ = sin 60° = 0.8660.
    • sin β = 0.25 × 0.8660 = 0.2165 ⇒ β ≈ 12.50°; cos β ≈ 0.9762; tan β ≈ 0.2219.
  2. Slider velocity using exact instantaneous relation: v_B = −ω_1 r sin θ + ω_1 r cos θ tan β.

    • Numbers: ω_1 r = 100 × 0.05 = 5.00 m/s; sin θ = 0.8660; cos θ = 0.5; tan β = 0.2219.
    • v_B = −5.00 × 0.8660 + 5.00 × 0.5 × 0.2219 = −4.330 + 0.55475 = −3.775 m/s.
    • Direction: negative means 3.775 m/s to the left (toward O).
  3. Connecting rod angular velocity: ω_rod = (ω_1 r cos θ) / (l cos β).

    • Numbers: numerator = 100 × 0.05 × 0.5 = 2.50; denominator = 0.20 × 0.9762 = 0.19524.
    • ω_rod = 2.50 / 0.19524 = 12.80 rad/s (CCW).

Answer: (i) Slider velocity = −3.775 m/s (leftward). (ii) Connecting rod angular velocity = 12.80 rad/s CCW.

Example 2 — Slider in a rotating arm with Coriolis and link angular acceleration (GATE-level) Given: A slot arm OA rotates CCW with angular velocity ω = 10 rad/s and angular acceleration α = 20 rad/s² at an instant. A slider P is at radius r = 0.30 m and moves outward along the slot with relative speed v_rel = 0.50 m/s and relative acceleration a_rel = 1.00 m/s². Find the absolute velocity and acceleration of P, giving components along u_r (radial, outward) and u_t (tangential, CCW).

Steps:

  1. Absolute velocity: v_P = v_rel u_r + ω r u_t.

    • Numbers: ω r = 10 × 0.30 = 3.00 m/s (tangential), v_rel = 0.50 m/s (radial outward).
    • Components: v_r = +0.50 m/s; v_t = +3.00 m/s.
    • Magnitude: |v_P| = sqrt(0.50² + 3.00²) = sqrt(0.25 + 9.00) = sqrt(9.25) = 3.041 m/s.
  2. Absolute acceleration: a_P = (−ω² r + a_rel) u_r + (α r + 2 ω v_rel) u_t.

    • Compute radial: −ω² r + a_rel = −(10)² × 0.30 + 1.00 = −100 × 0.30 + 1.00 = −30.0 + 1.0 = −29.0 m/s² (inward since negative along u_r).
    • Compute tangential: α r + 2 ω v_rel = 20 × 0.30 + 2 × 10 × 0.50 = 6.0 + 10.0 = +16.0 m/s² (CCW).
    • Magnitude: |a_P| = sqrt(29.0² + 16.0²) = sqrt(841 + 256) = sqrt(1097) = 33.14 m/s².

Answer: v_P = 0.50 u_r + 3.00 u_t m/s (|v_P| = 3.041 m/s). a_P = −29.0 u_r + 16.0 u_t m/s² (|a_P| = 33.14 m/s²).

Common mistakes

  • Forgetting the Coriolis term (2 ω v_rel) for sliders in rotating links; or getting its direction wrong (it is 90° ahead of the slot in the sense of rotation).
  • Mixing normal and tangential components in acceleration polygons; omitting the −ω² r component or assigning it the wrong direction.
  • Using IC method for acceleration (it is for velocities only) or assuming ICs are fixed in place as the mechanism moves.
  • Sign errors: not maintaining CCW positive for ω, α, and consistent x–y directions; or not keeping slider direction constraints (velocity/acceleration strictly along line of stroke).
  • Applying the long-rod approximation (l ≫ r) where r/l is not small; leads to noticeable error in piston velocity/acceleration.
  • In loop-closure differentiation, forgetting to differentiate both magnitude and direction (e.g., d/dt of e^{jθ} = j ω e^{jθ}); or dropping the −r ω² terms in the acceleration loop.

For GATE ME

  • Conceptual checks:
    • Count of instantaneous centers N_IC and Kennedy’s theorem usage to locate ICs; directions of velocities from ICs.
    • Presence/absence and direction of Coriolis acceleration; conditions when it is zero (no sliding or ω = 0).
    • Limiting cases at dead centers in slider-crank; qualitative velocity/acceleration behavior.
  • Numericals to practise:
    • Slider-crank: find slider velocity and acceleration at a given crank angle; find connecting-rod angular velocity/acceleration using relative velocity/acceleration resolution.
    • Slider on rotating arm: compute absolute velocity/acceleration including Coriolis with given ω, α, v_rel, a_rel.
    • Four-bar: given r_i, θ_2, ω_2 (and possibly α_2), solve θ_3, θ_4; then ω_3, ω_4; and α_3, α_4 by loop-closure differentiation (complex form or Cartesian components).
    • Graphical velocity/acceleration polygon construction questions (qualitative or scaled numericals). Be ready to state directions of normal/tangential components and close polygons.
  • Speed tips:
    • Memorize unit vector and cross-product patterns for planar problems; write u_t = k × u_r.
    • For slider-crank, pre-derive sin β = (r/l) sin θ and keep a simple calculator routine: compute β, then v_B and ω_rod using the relations given here.
    • For Coriolis direction, use the “rotate v_rel by +90° for CCW ω” rule.

Quick check

  1. A slider moves outward at 0.2 m/s along a slot in a link rotating CCW at 8 rad/s. What is the Coriolis acceleration magnitude and its direction relative to the slot?
  2. In a four-bar with n = 4 links (including ground), how many instantaneous centers exist among the links?
  3. For a slider-crank with l ≫ r, give the approximate expressions for slider velocity and acceleration at crank angle θ if the crank rotates at constant ω.

Answers: (1) a_cor = 2 ω v_rel = 2 × 8 × 0.2 = 3.2 m/s², directed 90° ahead of the slot in the CCW sense; (2) N_IC = n(n − 1)/2 = 6; (3) v ≈ ω r sin θ, a ≈ ω² r cos θ (approximate, valid for l ≫ r).

Finished this topic? Mark it so your progress, study plan and readiness keep up.

Stuck on something here?