Mechanics of machining

Mechanics of machining explains chip formation, cutting forces, shear plane, friction at the tool–chip interface, Merchant’s theory, and how to compute power, stresses, and efficiency in metal cutting.

Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.

Why it matters

  • Mechanics of machining lets you predict cutting forces, power, temperatures, and chip behavior so you can choose speeds/feeds, select tools, avoid chatter, protect the spindle, and ensure surface integrity.
  • Exams and interviews ask you to compute shear angle, friction, stresses on the shear plane, and specific energy; in industry, these govern tool life, MRR, and machining cost.

Key ideas

  • Orthogonal versus oblique cutting

    • In orthogonal cutting, the cutting edge is perpendicular to the cutting velocity and chip flow is in a plane normal to the edge; this is the standard 2D model for theory and GATE problems.
    • Oblique cutting has the cutting edge inclined; chip flows sideways. For this topic, we mostly use the orthogonal model; oblique cutting is referenced but not developed (see Tool geometry, wear and tool life for full 3D geometry).
  • Minimum definitions from tool geometry (see Tool geometry, wear and tool life for complete nomenclature)

    • Rake face is the face over which the chip flows. Clearance face avoids rubbing with the newly machined surface.
    • The basic angle is the rake angle α (measured in the orthogonal plane); positive α makes shearing easier.
  • Chip formation and chip ratio

    • When a sharp tool cuts a ductile metal, material shears along a narrow zone (idealized as a single shear plane at angle φ to the cutting velocity) forming a chip thicker than the uncut layer.
    • Define uncut chip thickness t1 and chip thickness t2 (measured normal to the cutting velocity in the orthogonal plane). The cutting ratio r = t1/t2 (0 < r < 1). The chip compression ratio Rc = t2/t1 = 1/r.
  • Forces, measurements, and sign conventions

    • A 2-component dynamometer measures: cutting (tangential) force Fc in the direction of cutting speed, and thrust force Ft (perpendicular to Fc in the orthogonal plane, typically pushing the tool into the work). Take Fc > 0 along the cutting speed; Ft > 0 pushing the tool into the work.
    • At the tool–chip interface: friction force F up the rake face and normal force N pressing the chip onto the rake face. Define friction coefficient μ = F/N and friction angle β where tan β = μ.
  • Transformations among force systems (orthogonal cutting)

    • Along/normal to rake face in terms of dynamometer forces:
      • F = Fc sin α + Ft cos α
      • N = Fc cos α − Ft sin α
      • μ = F/N = tan β
    • Along/normal to the shear plane (shear force Fs and normal force Fn) from dynamometer forces:
      • Fs = Fc cos φ − Ft sin φ
      • Fn = Fc sin φ + Ft cos φ
  • Shear plane area, stress, and strain

    • The shear plane area As is the area of the plane on which the main plastic shear occurs: As = (b t1)/sin φ, where b is the width of cut (depth of cut in turning considered as width in the orthogonal plane).
    • Average shear stress on the shear plane: τs = Fs/As.
    • Shear strain in orthogonal cutting (kinematic relation): γ = tan(φ − α) + cot φ. Typical values for ductile metals are ~2–5 (order of magnitude; material and conditions dependent).
  • Geometry links among r, α, and φ (orthogonal cutting)

    • Exact kinematic relation: tan φ = (r cos α)/(1 − r sin α). This follows from geometric compatibility of chip flow and the single-shear-plane idealization.
  • Merchant’s theory and Merchant circle

    • Assumptions: steady-state cutting, single shear plane, homogeneous perfectly plastic behavior in the shear zone, constant μ at the tool–chip interface, plane strain (orthogonal), and minimum total energy (or maximum shear stress) criterion determining φ.
    • Merchant’s shear-angle formula: φ = 45° + α/2 − β/2. (β from μ = tan β.) This is a standard first approximation; real machining often deviates due to strain hardening, temperature rise, non-uniform μ, and finite shear zone thickness.
    • Merchant circle construction graphically relates Fc, Ft, F, N, Fs, Fn, α, β, and φ; in analysis we use the algebraic relations above.
  • Power, MRR, and specific energy

    • Cutting speed V is the relative speed along Fc (e.g., in turning V = π D n / 60).
    • Material removal rate (orthogonal model): MRR = b t1 V.
    • Cutting power: P = Fc V. Spindle power must exceed P, considering drive efficiency.
    • Specific cutting energy (or specific energy of machining): u = P/MRR = Fc/(b t1). This is an indicator of process efficiency; it rises at small undeformed chip thickness due to size effect and ploughing.
  • Why real cutting differs from the ideal model

    • Shear occurs in a finite shear zone with temperature-dependent flow stress and strain hardening, not a strict plane.
    • Interface friction is not perfectly Coulombic; sticking–sliding occurs. μ and β vary with speed, rake, and lubrication.
    • Built-up edge (BUE) can form at low speeds and small rake, effectively altering α and raising Ft; with higher speed and sharper tools, BUE decreases, improving finish.
    • Oblique effects and 3D chip flow (side spread) violate plane-strain assumptions in many operations.
  • Brief note on oblique cutting (for awareness)

    • The chip flow angle ηc (angle between chip flow and the normal to cutting edge) is often approximated by Stabler’s rule: ηc ≈ i, where i is the inclination angle of the cutting edge (empirical). Detailed oblique cutting mechanics are treated under Tool geometry, wear and tool life.

Formulas

r = t1 / t2

  • Cutting ratio; t1 = uncut chip thickness (m), t2 = chip thickness (m). Orthogonal cutting.

Rc = t2 / t1 = 1 / r

  • Chip compression ratio. Orthogonal cutting.

tan φ = (r cos α) / (1 − r sin α)

  • Shear-plane angle from geometry; φ in radians (or degrees consistently), α = rake angle. Orthogonal cutting with single shear-plane idealization.

γ = tan(φ − α) + cot φ

  • Shear strain in orthogonal cutting; φ, α in radians (or degrees consistently). Orthogonal cutting, plane strain.

F = Fc sin α + Ft cos α

  • Friction force on rake face F (N) from dynamometer forces Fc (N), Ft (N); α in radians (or degrees consistently). Orthogonal cutting.

N = Fc cos α − Ft sin α

  • Normal force on rake face N (N). Same conditions as above.

μ = F / N = tan β

  • Coefficient of friction μ (dimensionless); friction angle β (rad or deg). Orthogonal cutting.

Fs = Fc cos φ − Ft sin φ

  • Shear force along shear plane Fs (N). Orthogonal cutting.

Fn = Fc sin φ + Ft cos φ

  • Normal force on shear plane Fn (N). Orthogonal cutting.

As = (b t1) / sin φ

  • Shear plane area As (m²); b = width of cut (m), t1 (m), φ in rad/deg. Orthogonal cutting.

τs = Fs / As

  • Average shear stress on shear plane τs (Pa). Orthogonal cutting.

V = π D n / 60

  • Cutting speed in turning; V (m/s), D (m), n (rev/min). Turning, steady speed.

MRR = b t1 V

  • Material removal rate (m³/s) in orthogonal model; b (m), t1 (m), V (m/s). Turning/milling under orthogonal approximation.

P = Fc V

  • Cutting power P (W) ignoring drive losses. Any machining where Fc and V are defined.

u = P / MRR = Fc / (b t1)

  • Specific cutting energy u (J/m³). Orthogonal assumption, steady cutting.

φ = 45° + α/2 − β/2

  • Merchant shear-angle formula; α, β in degrees (or radians consistently). Orthogonal cutting, Merchant assumptions.

Worked examples

Given: Orthogonal cutting with rake angle α = 10°, uncut chip thickness t1 = 0.20 mm, chip thickness t2 = 0.50 mm. Find r, φ, and γ.

  1. Cutting ratio: r = t1/t2 = 0.20/0.50 = 0.40 (dimensionless).
  2. Shear angle using tan φ = (r cos α)/(1 − r sin α).
    • α = 10° → cos α = 0.9848, sin α = 0.1736 (rounded).
    • tan φ = (0.40 × 0.9848)/(1 − 0.40 × 0.1736) = 0.3939/0.9306 = 0.4233.
    • φ = arctan(0.4233) ≈ 23.0°.
  3. Shear strain using γ = tan(φ − α) + cot φ.
    • φ − α = 23.0° − 10.0° = 13.0°; tan(13.0°) ≈ 0.2309.
    • tan φ ≈ tan(23.0°) ≈ 0.4245 → cot φ ≈ 1/0.4245 ≈ 2.354.
    • γ = 0.2309 + 2.354 ≈ 2.585 (dimensionless). Answer: r = 0.40, φ ≈ 23.0°, γ ≈ 2.585.
  • Example 2 — GATE-level combined forces, stress, power (turning, orthogonal approximation) Given: Turning of D = 60 mm bar at n = 600 rpm; depth of cut d = 2.0 mm; feed f = 0.25 mm/rev; rake angle α = 15°; measured forces Fc = 1000 N, Ft = 800 N; measured chip thickness t2 = 0.60 mm. Assume orthogonal cutting: uncut thickness t1 ≈ f, width of cut b ≈ d. Find: (a) r and φ, (b) μ and β, (c) τs, (d) P, MRR, and u.
    1. Cutting speed: V = π D n / 60 = π × 0.060 m × 600/60 = π × 0.060 × 10 ≈ 1.885 m/s.
    2. Uncut thickness and width: t1 = f = 0.25 mm = 0.00025 m; b = d = 2.0 mm = 0.002 m.
    3. Cutting ratio: r = t1/t2 = 0.25/0.60 = 0.4167.
    4. Shear angle using tan φ = (r cos α)/(1 − r sin α).
      • α = 15° → cos α = 0.9659, sin α = 0.2588.
      • tan φ = (0.4167 × 0.9659)/(1 − 0.4167 × 0.2588) = 0.4025/0.8922 = 0.4513.
      • φ = arctan(0.4513) ≈ 24.31°.
    5. Friction force and normal on rake face using F = Fc sin α + Ft cos α and N = Fc cos α − Ft sin α.
      • F = 1000 × 0.2588 + 800 × 0.9659 = 258.8 + 772.7 ≈ 1031.6 N.
      • N = 1000 × 0.9659 − 800 × 0.2588 = 965.9 − 207.1 ≈ 758.9 N.
      • μ = F/N ≈ 1031.6/758.9 ≈ 1.360 (dimensionless); β = arctan μ ≈ 53.94°.
    6. Shear force using Fs = Fc cos φ − Ft sin φ.
      • cos φ = cos 24.31° ≈ 0.9110; sin φ ≈ 0.4125.
      • Fs = 1000 × 0.9110 − 800 × 0.4125 = 910.99 − 329.99 ≈ 581.0 N.
    7. Shear-plane area As = (b t1)/sin φ = (0.002 × 0.00025)/0.4125 = 5.00×10⁻⁷/0.4125 ≈ 1.212×10⁻⁶ m².
    8. Average shear stress τs = Fs/As = 581.0 / (1.212×10⁻⁶) ≈ 4.80×10⁸ Pa ≈ 480 MPa.
    9. Power P = Fc V = 1000 × 1.885 ≈ 1.885 kW.
    10. MRR = b t1 V = 0.002 × 0.00025 × 1.885 = 9.425×10⁻⁷ m³/s.
    11. Specific energy u = Fc/(b t1) = 1000/(0.002 × 0.00025) = 1000/5×10⁻⁷ = 2.0×10⁹ J/m³. Answers: (a) r = 0.4167, φ ≈ 24.31°; (b) μ ≈ 1.36, β ≈ 53.94°; (c) τs ≈ 4.80×10⁸ Pa (≈ 480 MPa); (d) P ≈ 1.885 kW, MRR ≈ 9.425×10⁻⁷ m³/s, u ≈ 2.0×10⁹ J/m³.

Assumptions stated: orthogonal cutting; single-shear-plane model; steady-state cutting; in turning, t1 ≈ feed and b ≈ depth of cut.

Common mistakes

  • Angle units and references: using degrees in trig functions expecting radians; or measuring α in the wrong plane. In orthogonal analysis, α is the orthogonal rake angle.
  • Sign errors in force transformations: F = Fc sin α + Ft cos α and N = Fc cos α − Ft sin α; swapping sin/cos or signs gives unphysical μ.
  • Applying Merchant’s φ formula blindly when BUE, strong strain hardening, or heavy sticking friction invalidates assumptions; compare with φ from r to sanity-check.
  • Using MRR incorrectly: for turning under orthogonal approximation, use MRR = b t1 V with b ≈ depth of cut and t1 ≈ feed; do not multiply again by width or circumference inadvertently.
  • Forgetting unit consistency: convert mm to m before computing As, τs, MRR, and u.

For GATE ME

  • Quick numericals: compute φ from r and α; compute μ, β from Fc, Ft, and α; compute τs from Fc, Ft, φ, t1, b.
  • Merchant theory: state assumptions and write φ = 45° + α/2 − β/2; compare with φ from r. Expect conceptual questions on when Merchant deviates and why.
  • Force transformations: given Fc and Ft, find F, N, Fs, Fn; or invert relationships. Know the four key equations.
  • Energy and rates: compute P = Fc V; MRR = b t1 V; u = Fc/(b t1); interpret trends with t1 (size effect) qualitatively.
  • Chip formation and BUE: qualitative conditions for continuous, serrated, and discontinuous chips; effect of α, V, and lubrication on chip type and surface finish. Keep this concise; detailed metallurgy is under Machining Processes.
  • Turning kinematics: compute V = π D n / 60 and relate t1 ≈ feed, b ≈ depth of cut under orthogonal approximation.

Quick check

  1. In orthogonal cutting with α = 12°, t1 = 0.15 mm, t2 = 0.45 mm, is φ closer to 20° or 30°?
  2. A dynamometer reads Fc = 500 N, Ft = 300 N; α = 10°. Is μ closer to 0.6 or 1.0?
  3. If V doubles but Fc and b, t1 remain the same, what happens to P and u?

Answers: 1) 20° (φ ≈ arctan[(r cos α)/(1 − r sin α)] with r = 0.333 → φ ≈ 20–21°). 2) About 0.8–0.9 (μ = (Fc sin α + Ft cos α)/(Fc cos α − Ft sin α)). 3) P doubles (∝ V); u unchanged (= Fc/(b t1)).

Finished this topic? Mark it so your progress, study plan and readiness keep up.

Stuck on something here?