Engineering materials and their properties
Definitions, property maps, test methods, and key formulas linking structure–processing–properties for metals, polymers, ceramics, and composites, with stress–strain, hardness, toughness, creep, fatigue, thermal/electrical behavior, and selection tips.
Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.
Why it matters
Choosing the right engineering material is often the difference between a product that is light yet strong, durable yet economical, and safe under all operating conditions. Understanding properties and how they change with temperature, strain rate, composition, processing, and environment lets you select, process, and qualify materials for manufacturing, testing, and service.
Key ideas
Engineering material: a substance used to make components that must meet specified mechanical, thermal, electrical, chemical, and economic requirements. Classes: metals (ferrous, non‑ferrous), polymers, ceramics and glasses, composites, and emerging smart materials.
Structure–processing–properties–performance (SPPP) link: processing (casting, forming, heat treatment, joining, surface engineering) sets microstructure (grains, phases, defects), which controls properties, which determine performance.
Microstructure terms: grain (crystal region with a given orientation), phase (region with uniform structure/composition), defect (vacancy, dislocation, grain boundary). In steels: ferrite (soft, BCC), austenite (FCC, high solubility), pearlite (lamellar ferrite+cementite), cementite (Fe3C, hard), martensite (supersaturated BCT, very hard). Details of transformations belong to “Phase diagrams and heat treatment”.
Property categories (what matters and how measured)
- Mechanical properties: stiffness (Young’s modulus E), strength (yield σy, ultimate σu), ductility (elongation, reduction in area), hardness (indentation resistance), toughness (energy to fracture; fracture toughness KIC), fatigue (life under cyclic load), creep (time‑dependent deformation at high temperature), wear resistance (tribology — see “Tribology”).
- Thermal properties: thermal conductivity k, specific heat c, coefficient of thermal expansion α, thermal diffusivity a = k/(ρc), thermal shock resistance.
- Physical/electrical/magnetic: density ρ, electrical resistivity ρe, magnetic behavior (ferromagnetic, paramagnetic, diamagnetic), optical (for glasses/polymers).
- Chemical: corrosion resistance (uniform, pitting, crevice, galvanic, intergranular, stress corrosion cracking), oxidation.
- Manufacturability: castability, formability, machinability, weldability. These arise from combinations of above properties and microstructure.
Metals vs polymers vs ceramics vs composites (typical trends; remember exceptions)
- Metals: high E (steels ≈ 200 GPa; Al ≈ 69 GPa), good ductility/toughness, conductive; strength and toughness tunable by alloying and heat treatment; prone to corrosion (unless stainless/Al with passivation). Ferrous (steels, cast irons) dominate structural loads; non‑ferrous (Al, Cu, Ti, Mg, Ni) trade density, corrosion, high‑T performance.
- Polymers: low density (≈ 900–1400 kg/m³), low E (≈ 1–3 GPa for thermoplastics), viscoelastic, sensitive to temperature/strain rate; great for corrosion resistance and cost, limited high‑T strength; additives/fillers improve performance.
- Ceramics/glasses: very high E (≈ 200–400 GPa) and hardness, excellent high‑T stability and corrosion resistance; brittle with low fracture toughness; thermal shock is a design challenge.
- Composites: combine matrix and reinforcement for specific strength (σ/ρ) and specific stiffness (E/ρ); properties are anisotropic; manufacturing (layup, curing) largely determines performance; interfaces are critical.
Stress–strain: foundations and test outputs
- Engineering stress σ = P/A0 and engineering strain ε = ΔL/L0. True stress σt = P/A and true strain εt = ln(L/L0). For uniform tensile deformation before necking: σt = σ(1+ε) and εt = ln(1+ε).
- Hooke’s law (uniaxial): In the linear elastic range, σ = E ε (tension positive). For shear, τ = G γ. Assumptions: small strain, homogeneous, isotropic material.
- Elastic constants for isotropic solids: E, shear modulus G, bulk modulus K, Poisson’s ratio ν are related (see Formulas). Typical ν: metals ≈ 0.27–0.35; ceramics ≈ 0.2; polymers vary widely.
- Yielding: yield strength σy (offset 0.2% for materials without a clear yield point). Ultimate tensile strength σu at maximum engineering stress. Necking criterion (Considère): in tension, necking starts when dσt/dεt = σt.
- Toughness: area under the stress–strain curve to fracture (units of energy/volume). For notched bodies, use fracture toughness KIC (plane strain critical stress intensity) to quantify crack resistance.
Hardness
- Indentation hardness correlates with strength for many metals. Brinell (HBW), Vickers (HV), Rockwell (HRC/HRB). Empirical conversions are alloy/process dependent; use with caution.
Time/temperature‑dependent behavior
- Creep: time‑dependent plastic strain at high T (for metals, T ≳ 0.4–0.5 Tm in K). Primary (decelerating), secondary (steady rate), tertiary (accelerating to rupture). Steady‑state often follows Norton’s law ε̇ = A σn exp(−Q/RT).
- Fatigue: cyclic stress can fail a component below σy via crack initiation and growth. S–N (Wöhler) curves (stress amplitude vs cycles to failure) often fit Basquin’s law in high‑cycle domain; mean stress effects by Goodman or Soderberg. For crack growth, Paris law (da/dN = C (ΔK)m) applies in Region II for long cracks; threshold ΔKth and KIC bound the regime.
Thermal and electrical
- Thermal expansion: ΔL = α L ΔT, may induce thermal stress if constrained. Typical α: steels ≈ 12×10⁻⁶/K; Al ≈ 23×10⁻⁶/K; many ceramics ≈ 5–8×10⁻⁶/K; polymers higher and temperature dependent.
- Thermal conductivity k: metals high, polymers/ceramics often lower (with exceptions like SiC, AlN). Fourier’s law qx = −k A dT/dx in 1D steady conduction.
- Electrical resistivity ρe: metals low; increases with temperature (approximately linear near room T); semiconductors decrease with temperature; polymers and ceramics typically insulating unless filled/doped.
Corrosion (overview; details in “Surface Engineering” and “NDT” for detection)
- Types: uniform (general), galvanic (dissimilar metals in electrolyte), pitting/crevice (localized), intergranular, stress corrosion cracking (SCC). Control: material selection (alloying, passivation), design (avoid crevices), coatings, inhibitors, cathodic protection, control of environment.
Selection strategies
- Use charts of property against property (Ashby maps) to maximize indices like E/ρ (stiffness per weight), σy/ρ (strength per weight), k/(Eα) (thermal shock), KIC/E (fracture tolerance), or process‑specific indices. Tie properties back to processing routes you can apply in manufacturing.
Real vs ideal behavior
- Real materials show anisotropy, defects, residual stresses, and variability (heat‑to‑heat, processing route). Properties change with temperature, strain rate, and environment; test results depend on specimen geometry and standard methods. Indentation hardness–strength correlations are approximate and alloy‑dependent. Fracture parameters (KIC, JIC) depend on thickness (plane strain vs plane stress) and constraint.
Formulas
σ = P / A0
Engineering stress. P: load (N), A0: original cross‑section (m²). Applies to uniaxial tests using original area.
ε = ΔL / L0
Engineering strain. ΔL: extension (m), L0: original gauge length (m). Small strain assumption.
σt = P / A, εt = ln(L / L0), σt = σ (1 + ε) (uniform stage)
True stress/strain and relation to engineering values before necking. A: instantaneous area (m²). Valid before necking in tension.
σ = E ε
Hooke’s law (uniaxial, linear elastic). E: Young’s modulus (Pa). Valid in elastic range for homogeneous, isotropic material.
τ = G γ
Shear stress–strain in linear elastic regime. G: shear modulus (Pa), γ: engineering shear strain (rad, dimensionless).
E = 2 G (1 + ν)
Isotropic elastic constants relationship. ν: Poisson’s ratio (dimensionless). Valid for linear elastic, isotropic solids.
E = 3 K (1 − 2 ν)
Relates bulk modulus K (Pa) to E and ν for isotropic, linear elastic materials.
KIC = Y σ √(π a)
Mode I plane‑strain fracture toughness criterion. KIC: critical stress intensity (Pa√m), Y: geometry factor (dimensionless), σ: nominal stress (Pa), a: crack size (m; for a center crack, a is half‑length). Valid under LEFM, small‑scale yielding.
ΔL = α L ΔT
Thermal expansion. α: coefficient of linear thermal expansion (1/K), L: original length (m), ΔT: temperature change (K). Unrestrained expansion.
qx = − k A dT/dx
Fourier’s law (1D, steady). qx: heat rate (W), k: thermal conductivity (W/m·K), A: area (m²), dT/dx: temperature gradient (K/m).
ε̇ = A σⁿ exp(−Q / (R T))
Norton’s law for steady‑state (secondary) creep. ε̇: creep strain rate (1/s), A: material constant, n: stress exponent, Q: activation energy (J/mol), R: gas constant (8.314 J/mol·K), T: absolute temperature (K). Valid where secondary creep dominates.
σa Nᵇ = C
Basquin relation for high‑cycle fatigue (HCF) in fully reversed or specified R‑ratio conditions. σa: stress amplitude (Pa), N: cycles to failure, b<0, C>0 depend on material and R. Empirical, limited to HCF regime.
HBW = 2 P / (π D (D − √(D² − d²)))
Brinell hardness using SI units. HBW in N/mm² (MPa) if P in N and D, d in mm. P: load, D: ball diameter, d: indentation diameter. Valid within standard test limits (no edge effects, valid indentation size).
HV = 1.854 P / d²
Vickers hardness with P in N, d (diagonal) in mm gives HV in MPa. 1.854 is the geometrical constant for a 136° diamond pyramid. Empirical testing standard applies.
ρ = m / V
Density. ρ: density (kg/m³), m: mass (kg), V: volume (m³). Basic definition.
Specific stiffness = E / ρ, Specific strength ≈ σy / ρ
Material indices for lightweight design. E, σy in Pa; ρ in kg/m³. Use for comparative selection; actual design also checks buckling, fatigue, etc.
Condition for necking (Considère): dσt/dεt = σt
Necking onset in tensile test of ductile materials under monotonic loading. Derived from maximum load condition in engineering stress–strain.
Worked examples
Given: A circular steel bar, diameter d = 20 mm, length L0 = 1.2 m, axial load P = 40 kN. Material: E = 200 GPa, yield strength σy = 250 MPa. Find (a) engineering stress, (b) elastic elongation, (c) factor of safety against yield under this load.
- Cross‑sectional area: A0 = π d²/4 = π (0.020 m)² / 4 = 3.1416×10⁻⁴ m².
- Stress: σ = P/A0. Use P = 40,000 N. σ = 40,000 N / 3.1416×10⁻⁴ m² = 1.2732×10⁸ Pa = 127.32 MPa.
- Strain (elastic): ε = σ/E = (127.32×10⁶ Pa) / (200×10⁹ Pa) = 6.366×10⁻⁴.
- Elongation: ΔL = ε L0 = 6.366×10⁻⁴ × 1.2 m = 7.639×10⁻⁴ m = 0.764 mm.
- Factor of safety (yield): FOSy = σy / σ = 250 MPa / 127.32 MPa = 1.96.
Answer: Stress = 127.32 MPa; elongation = 0.764 mm; FOS (yield) = 1.96. All within elastic range.
Example 2 (GATE‑style, combined): From hardness to UTS estimate and fracture limit crack size A steel plate has been Brinell tested with a 10 mm ball under P = 29,420 N. The indentation diameter is d = 4.0 mm. In service, the plate sees a uniform tensile stress σ = 300 MPa. The measured plane‑strain fracture toughness is KIC = 80 MPa√m. Assume a wide plate with a central through crack (total length 2a) so that Y ≈ 1. Estimate (a) the Brinell hardness HBW (in MPa), (b) the ultimate tensile strength σu (in MPa) using the empirical relation σu ≈ 0.35 × HBW (HBW in MPa; suitable for plain/low‑alloy steels), and (c) the maximum allowable half‑crack length a to avoid fast fracture under plane strain.
Given: D = 10 mm, P = 29,420 N, d = 4.0 mm, σ = 300 MPa, KIC = 80 MPa√m, Y = 1.
(a) Brinell hardness HBW:
- Use HBW = 2P / (π D (D − √(D² − d²))).
- Compute √(D² − d²) = √(100 − 16) mm = √84 mm = 9.165 mm.
- Denominator = π × 10 × (10 − 9.165) = π × 10 × 0.835 = 26.23 mm² (rounded).
- Numerator = 2P = 58,840 N.
- HBW = 58,840 N / 26.23 mm² = 2,244 N/mm² = 2,244 MPa.
(b) Estimate σu from hardness: 6) σu ≈ 0.35 × HBW = 0.35 × 2,244 MPa = 785 MPa (approx.).
(c) Allowable half‑crack length a using KIC = Y σ √(π a): 7) Rearranged: a = (KIC / (Y σ √π))². 8) √π = 1.772; Denominator = 1 × 300 MPa × 1.772 = 531.6 MPa. 9) Ratio = 80 / 531.6 = 0.1505 √m. 10) a = (0.1505)² m = 0.0226 m = 22.6 mm.
Answer: HBW ≈ 2,244 MPa; estimated σu ≈ 785 MPa; maximum allowable half‑crack length a ≈ 22.6 mm for avoidance of fast fracture at σ = 300 MPa under plane strain.
Notes: The hardness–UTS conversion is approximate and alloy/heat‑treatment dependent; KIC applicability requires LEFM conditions and sufficient thickness for plane strain.
Common mistakes
- Confusing strength with stiffness: E (stiffness) is largely composition/microstructure independent for a class (e.g., steels ≈ 200 GPa), while yield/UTS vary widely.
- Using UTS instead of yield strength for static design, or applying hardness–strength correlations blindly across alloys/processes.
- Wrong elastic constants conversions: forgetting E = 2G(1+ν) or E = 3K(1−2ν).
- Hardness units: computing Brinell with SI but converting to empirical relations defined in kgf/mm² without unit consistency.
- Ignoring temperature and strain‑rate effects for polymers and metals at elevated temperatures; underpredicting creep/fatigue damage.
- Applying plane‑strain KIC where thickness/constraint is low (plane stress dominates), or using LEFM near large plastic zones.
- Neglecting residual stresses, surface condition, and environment (corrosion, SCC) when interpreting test properties.
For GATE ME
- Stress–strain fundamentals, 0.2% proof stress, true vs engineering measures, Considère criterion.
- Relationships among E, G, K, ν; volumetric strain under hydrostatic stress.
- Thermal expansion (free vs constrained), thermal stress basics.
- Hardness calculations (Brinell/Vickers) and cautious strength estimates; identification of suitable hardness test for a case.
- Fracture mechanics basics (KIC formula, geometry factor Y for simple cracks) and safe crack size under a given stress.
- Creep rate via Norton’s law; interpreting creep curves.
- Fatigue life using S–N/ Basquin and mean‑stress corrections (Goodman/Soderberg, conceptual where formulas are provided).
- Property trends and material selection (specific strength/stiffness), microstructure–property links in steels and nonferrous alloys.
- Practise: plotting/reading stress–strain; converting between elastic constants; unit‑consistent hardness calculations; quick LEFM crack size checks; back‑of‑envelope thermal strain and specific property comparisons.
Quick check
- A 1 m long Al rod (α = 23×10⁻⁶/K) heats by 60 K freely. What is ΔL?
- For an isotropic material with E = 210 GPa and ν = 0.3, find G.
- A wide plate (center crack) has σ = 200 MPa, KIC = 70 MPa√m. What is amax?
Answers: 1) ΔL = α L ΔT = 23×10⁻⁶ × 1 × 60 = 1.38 mm. 2) G = E/[2(1+ν)] = 210/[2(1.3)] ≈ 80.8 GPa. 3) a = (KIC/(σ√π))² = (70/(200×1.772))² ≈ (0.1977)² ≈ 0.0391 m = 39.1 mm.
Finished this topic? Mark it so your progress, study plan and readiness keep up.
Stuck on something here?