Radiation laws
Radiation laws: Planck’s law, Stefan–Boltzmann law, Wien’s displacement law, Kirchhoff’s law, Lambert’s cosine law; definitions of emissive power, irradiation, radiosity, intensity; emissivity/absorptivity/reflectivity/transmissivity; gray and black surfaces; diffuse emission; radiosity–irradiation
Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.
Why it matters
Thermal radiation governs heat transfer at high temperatures, in furnaces, gas turbines, IC engine components, solar collectors, spacecraft thermal control, and even electronics cooling when convection is limited. Correct use of radiation laws lets you estimate heat loads, choose coatings (low or high emissivity), and balance radiation with conduction and convection in design.
Key ideas
- Thermal radiation: electromagnetic energy emitted due to temperature, with no medium required. Dominant at high temperature and across vacuum.
- Blackbody: an ideal surface that absorbs all incident radiation (absorptivity α = 1), emits the maximum possible at a given temperature, and is diffuse (direction-independent emission). Real bodies emit less than a blackbody.
- Emissive power (E): total radiant energy emitted by a surface per unit area per unit time, W/m². For a blackbody, it is denoted Eb.
- Spectral quantities: radiation resolved by wavelength λ. Example: spectral emissive power Eλ (W/m³) is per unit wavelength interval (units W·m⁻²·m⁻¹). Similarly define spectral intensity Iλ and spectral emissivity ελ.
- Radiative intensity (I): power per unit projected area per unit solid angle leaving a surface, W/(m²·sr). It carries directional information. Hemispherical integration of I gives the total leaving the surface.
- Irradiation (G): total radiant energy incident on a surface per unit area, W/m².
- Radiosity (J): total radiant energy leaving a surface per unit area, including both emission and reflection, W/m². For a blackbody, J = Eb because there is no reflection.
- Emissivity (ε): measure of how closely a surface emits compared with a blackbody. Total hemispherical emissivity ε = E/Eb (0 ≤ ε ≤ 1). Spectral emissivity ελ = Eλ/Eλ,b; directional emissivity depends on direction as well.
- Absorptivity (α), Reflectivity (ρ), Transmissivity (τ): fractions of incident irradiation that are absorbed, reflected, and transmitted. Energy conservation at a surface requires α + ρ + τ = 1. For opaque surfaces, τ = 0 → α + ρ = 1.
- Diffuse surface: emits and reflects uniformly with respect to direction. A perfectly diffuse emitter obeys Lambert’s cosine law.
- Gray surface: properties independent of wavelength (ελ ≈ ε constant over λ). Real surfaces are often selective (ε varies with λ), especially metals vs oxides/paints.
Fundamental laws of thermal radiation:
- Planck’s law (spectral distribution of blackbody radiation): gives Eλ,b(λ, T). It predicts that at any T, emission spans a spectrum with a single peak; integrating over λ yields Stefan–Boltzmann.
- Stefan–Boltzmann law: the total blackbody emissive power Eb = σ T⁴, where σ is the Stefan–Boltzmann constant. Real surfaces: E = ε σ T⁴ (for diffuse–gray assumption).
- Wien’s displacement law: wavelength of peak blackbody emission obeys λmax T = b (Wien’s constant). Hotter bodies peak at shorter wavelengths.
- Kirchhoff’s law: at thermodynamic equilibrium, a body’s emissivity equals its absorptivity at each wavelength and direction, ελ,θ,φ = αλ,θ,φ. Useful hemispherical form: for a surface in an isothermal large black enclosure, total hemispherical ε = α. This justifies taking α = ε for enclosure radiation problems under the usual assumptions.
- Lambert’s cosine law: for a diffuse emitter/reflector, the intensity in direction θ from the surface normal varies as cosθ. Equivalently, the hemispherical leaving power E (or radiosity J) relates to direction-independent intensity I by E = π I (and for diffuse reflection + emission, J = π I).
Connecting laws to analysis of real surfaces:
- For an opaque diffuse–gray surface exchanging with its surroundings, it is standard to write the radiosity–irradiation relation: J = ε σ T⁴ + ρ G, with ρ = 1 − α. Under blackbody irradiation of the surroundings (e.g., a large black isothermal enclosure), α = ε by Kirchhoff’s law, so J = ε σ T⁴ + (1 − ε) G.
- The net radiative heat flux leaving the surface is qʺ = J − G. In the common “small surface in a large black enclosure at Tsur” case, G = Eb,sur = σ Tsur⁴, and with α = ε, qʺ = ε σ (T⁴ − Tsur⁴). Positive qʺ means net emission (surface loses heat by radiation).
- Sign convention: take heat flux positive when leaving the surface. If qʺ < 0, the surface is a net absorber.
Outline of origin/derivation (what is examined):
- Planck’s law arises from quantization of electromagnetic modes in a cavity (energy levels nhν) and Bose–Einstein statistics. Its exact expression uses fundamental constants h, c, and kB.
- Stefan–Boltzmann law is obtained by integrating Planck’s spectral distribution over all wavelengths and solid angles. The integration yields σ in terms of h, c, and kB (given below). You are not expected to reproduce the full integral in GATE; knowing the result, units, and assumptions is enough.
- Wien’s displacement law results from maximizing Planck’s spectral distribution with respect to λ; the product λmax T equals a universal constant b.
- Lambert’s cosine law follows from the definition of radiative intensity and geometry: the projected area of a surface element toward direction θ scales as cosθ; for a diffuse surface with direction-independent intensity, integrating I cosθ over the hemisphere gives π I.
Why real devices differ from the ideal:
- Real surfaces are not perfectly black (ε < 1). Metals often have low ε in the infrared (polished aluminum ~0.05–0.1), oxidized metals and paints have higher ε (~0.8–0.95). ε varies with T, surface finish, oxidation, and λ.
- Not all emission is diffuse; many surfaces are partially specular. Lambert’s law is an idealization; deviations affect view-factor-based exchange (see the separate topic “View factors and radiation exchange”).
- Kirchhoff’s equality α = ε is exact at thermodynamic equilibrium or for irradiation from a black isothermal surrounding; for arbitrary non-black, non-thermal spectra (e.g., solar spectrum on a cool surface), solar absorptance need not equal thermal emittance.
Standard cases and limiting cases you should know:
- Blackbody: ε = 1, α = 1, ρ = 0, τ = 0, J = Eb = σ T⁴.
- Perfect mirror: ε = 0, α = 0, ρ = 1, τ = 0 → J = ρ G = G (all incident is reflected).
- Opaque diffuse–gray: τ = 0, ε constant and direction-independent, J = ε σ T⁴ + (1 − ε) G; qʺ = J − G.
- Small surface in large black enclosure: G = σ Tsur⁴; qʺ = ε σ (T⁴ − Tsur⁴).
Formulas
Eλ,b(λ, T) = (2π h c²)/(λ⁵) · 1/(exp(h c/(λ kB T)) − 1)
Spectral blackbody emissive power per unit wavelength. Eλ,b in W·m⁻³, λ in m, T in K; h = 6.62607015×10⁻³⁴ J·s, c = 2.99792458×10⁸ m/s, kB = 1.380649×10⁻²³ J/K. Applies to ideal blackbody.
Iλ,b(λ, T) = (2 h c²)/(λ⁵) · 1/(exp(h c/(λ kB T)) − 1)
Spectral blackbody intensity (radiance) per unit wavelength, W·m⁻³·sr⁻¹. For a diffuse blackbody, Eλ,b = π Iλ,b. Applies to ideal blackbody.
Eb = σ T⁴
Stefan–Boltzmann law: total blackbody emissive power. Eb in W/m², T in K, σ = 5.670374419×10⁻⁸ W·m⁻²·K⁻⁴. Ideal blackbody.
E = ε σ T⁴
Total emissive power of a diffuse–gray surface. E in W/m², ε (dimensionless, 0–1), T in K, σ as above. Assumes diffuse, gray surface; no irradiation term included (this is emission only).
λmax · T = b
Wien’s displacement law. λmax in m, T in K, b = 2.897771955×10⁻³ m·K. Ideal blackbody spectrum.
ε = E/Eb, ελ = Eλ/Eλ,b
Definitions of total hemispherical emissivity and spectral emissivity. Dimensionless (0–1).
α + ρ + τ = 1
Energy conservation at a surface under irradiation. Dimensionless fractions. For opaque surfaces, τ = 0 → α + ρ = 1.
ελ,θ,φ = αλ,θ,φ (at thermodynamic equilibrium)
Kirchhoff’s law (spectral, directional). Dimensionless. Total hemispherical ε = α when the surface is in an isothermal large black enclosure.
dEθ = I(θ, φ) cosθ dΩ
Definition relating directional intensity to differential emitted flux. dEθ in W/m², I in W·m⁻²·sr⁻¹, θ from surface normal, dΩ in sr. For diffuse emitter, I is constant with direction.
E = ∫hemisphere I cosθ dΩ = π I (diffuse)
Lambert’s cosine law integrated over the hemisphere. E (or J for total leaving) in W/m²; I in W·m⁻²·sr⁻¹. Applies to diffuse emission/reflection.
J = ε σ T⁴ + ρ G
Radiosity of a surface combining emission and reflection. J, G in W/m²; ε, ρ dimensionless. General for opaque/diffuse when ρ is hemispherical reflectivity. In a large black enclosure, use ρ = 1 − ε (since α = ε) so J = ε σ T⁴ + (1 − ε) G.
qʺ = J − G
Net radiative heat flux leaving a surface. qʺ in W/m². Positive means net emission; negative means net absorption. Always valid by definition of radiosity and irradiation.
σ = (2 π⁵ kB⁴)/(15 h³ c²)
Stefan–Boltzmann constant in terms of fundamental constants. σ in W·m⁻²·K⁻⁴. Derived by integrating Planck’s law over all wavelengths and directions.
Worked examples
Example 1 — Direct application of Stefan–Boltzmann and Wien’s laws Given: A blackbody at T = 1200 K. Find (a) its total emissive power Eb, (b) the wavelength λmax at which emission peaks, and (c) the (direction-independent) intensity Ib for a diffuse blackbody.
Assumptions: Ideal blackbody; diffuse emission; SI units.
Data: σ = 5.670374419×10⁻⁸ W·m⁻²·K⁻⁴; b = 2.897771955×10⁻³ m·K; π = 3.141592654.
Total emissive power Eb Formula:
Eb = σ T⁴Numbers: T⁴ = (1200 K)⁴ = 2.0736×10¹² K⁴; Eb = 5.670374419×10⁻⁸ × 2.0736×10¹² W/m² = 1.17580884×10⁵ W/m². Answer: Eb ≈ 1.176×10⁵ W/m².Peak wavelength λmax Formula:
λmax T = bNumbers: λmax = b/T = (2.897771955×10⁻³ m·K)/(1200 K) = 2.41481×10⁻⁶ m. Answer: λmax ≈ 2.415 μm.Diffuse blackbody intensity Ib Formula:
Eb = π Ib → Ib = Eb/πNumbers: Ib = (1.17580884×10⁵ W/m²) / 3.141592654 = 3.7427×10⁴ W·m⁻²·sr⁻¹. Answer: Ib ≈ 3.75×10⁴ W·m⁻²·sr⁻¹.
Example 2 — GATE-style: radiosity, net flux, and intensity for a gray surface in a black enclosure A diffuse–gray, opaque plate (area A = 2.0 m², emissivity ε = 0.80) at Ts = 700 K is mounted inside a large isothermal black enclosure at Tsur = 500 K. Find (a) irradiation G on the plate, (b) radiosity J of the plate, (c) net radiative heat transfer from the plate (Q), and (d) the direction-independent intensity I of radiation leaving the plate.
Assumptions: Large black enclosure → irradiation equals blackbody emission of surroundings; opaque and diffuse–gray surface; α = ε by Kirchhoff (enclosure case); SI units; steady conditions.
Data: σ = 5.670374419×10⁻⁸ W·m⁻²·K⁻⁴; π = 3.141592654.
Irradiation G Formula:
G = Eb,sur = σ Tsur⁴Numbers: Tsur⁴ = (500 K)⁴ = 6.25×10¹⁰ K⁴; G = 5.670374419×10⁻⁸ × 6.25×10¹⁰ W/m² = 3.543984×10³ W/m². Answer: G ≈ 3544 W/m².Radiosity J of the plate Formula (opaque, diffuse–gray in black enclosure):
J = ε σ Ts⁴ + (1 − ε) GNumbers: Ts⁴ = (700 K)⁴ = 2.401×10¹¹ K⁴ → σ Ts⁴ = 1.3614569×10⁴ W/m². Compute J: ε σ Ts⁴ = 0.80 × 1.3614569×10⁴ = 1.0891655×10⁴ W/m²; (1 − ε) G = 0.20 × 3.543984×10³ = 7.087968×10² W/m². J = 1.0891655×10⁴ + 7.087968×10² = 1.1600452×10⁴ W/m². Answer: J ≈ 1.160×10⁴ W/m².Net radiative heat flux and total heat transfer from the plate Formulae:
qʺ = J − GandQ = A qʺNumbers: qʺ = 1.1600452×10⁴ − 3.543984×10³ = 8.056468×10³ W/m². Q = 2.0 m² × 8.056468×10³ W/m² = 1.6112936×10⁴ W. Answers: qʺ ≈ 8.06 kW/m², Q ≈ 16.11 kW (leaving the plate).
Check (alternate compact formula): qʺ = ε σ (Ts⁴ − Tsur⁴) → 0.80 × (1.3614569×10⁴ − 3.543984×10³) = 8.056468×10³ W/m² (matches).
- Direction-independent intensity I of radiation leaving the plate
Formula (diffuse leaving):
J = π I → I = J/πNumbers: I = 1.1600452×10⁴ / 3.141592654 = 3.694×10³ W·m⁻²·sr⁻¹. Answer: I ≈ 3.69×10³ W·m⁻²·sr⁻¹.
Common mistakes
- Mixing wavelength units: b is in m·K; if you plug λ in μm without converting, answers will be off by 10⁶. State λ in meters unless the formula is explicitly in μm.
- Forgetting the π factor: Eb = π Ib for diffuse blackbody; similarly J = π I for diffuse leaving radiation. Missing π gives ~3.14× error.
- Assuming α = ε in all cases. It is guaranteed at thermodynamic equilibrium or when irradiated by a black isothermal surrounding; under non-thermal spectra (e.g., sunlight), absorptance can differ from thermal emittance.
- Confusing E (emission only) with J (emission plus reflection). Net flux is qʺ = J − G, not E − G in general.
- Omitting opacity assumption. If τ ≠ 0 (semi-transparent), then α + ρ + τ = 1; do not set ρ = 1 − ε unless α = ε and τ = 0 under the applicable conditions.
- Sign errors: By convention here, qʺ > 0 means net radiation leaving the surface; negative means net absorption.
For GATE ME
- Quick numericals using Stefan–Boltzmann and Wien’s laws: compute Eb, λmax, or compare radiative heat loss at two temperatures.
- Property definitions and concepts: identify/define emissivity (total vs spectral), absorptivity/reflectivity/transmissivity, irradiation, radiosity, intensity, black/gray/diffuse surfaces; interpret α + ρ + τ = 1 and special cases (opaque, blackbody).
- Conceptual on Kirchhoff’s law: when can we take α = ε; why a surface may have high solar absorptance but low thermal emittance (selective coatings).
- Apply Lambert’s cosine law: relate intensity and emissive power (E = π I); recognize diffuse vs specular behavior qualitatively.
- Radiosity–irradiation use in simple enclosure contexts (small surface in a large black isothermal surrounding): compute qʺ = ε σ (T⁴ − Tsur⁴), radiosity J, and sometimes the intensity I = J/π.
- Dimensional checks and units: W/m², W·m⁻²·sr⁻¹, W·m⁻³; understand what each means and when to use which. Practice: fast T⁴ arithmetic, careful unit conversion (μm ↔ m), picking the right relation (E vs J; G vs Eb,sur), and stating assumptions (blackbody, diffuse–gray, opaque, large enclosure).
Quick check
- A blackbody is at 1000 K. What is λmax? Use b = 2.8978×10⁻³ m·K.
- State the relation among α, ρ, τ for a surface; what is it for opaque surfaces?
- A diffuse–gray plate (ε = 0.7) at 600 K is in a large black enclosure at 300 K. What is qʺ (net leaving)? Use σ = 5.6704×10⁻⁸ W·m⁻²·K⁻⁴.
Answers: 1) λmax ≈ 2.898 μm. 2) α + ρ + τ = 1; for opaque, α + ρ = 1. 3) qʺ = ε σ (T⁴ − Tsur⁴) = 0.7×5.6704×10⁻⁸×(600⁴ − 300⁴) ≈ 0.7×5.6704×10⁻⁸×(1.296×10¹¹ − 8.1×10⁹) ≈ 0.7×5.6704×10⁻⁸×1.2159×10¹¹ ≈ 0.7×6.897×10³ ≈ 4.83×10³ W/m² (≈ 4.8 kW/m²).
Finished this topic? Mark it so your progress, study plan and readiness keep up.
Stuck on something here?