Heat exchangers: NTU method

NTU (Number of Transfer Units) method for sizing/rating heat exchangers using effectiveness–NTU relations for parallel, counterflow, and crossflow configurations.

Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.

Why it matters

Heat exchangers are everywhere: condensers in power plants, radiators in vehicles, economizers in boilers, air coolers in process plants. The NTU method lets you size a heat exchanger or find outlet temperatures when one or both outlet temperatures are unknown — a frequent design and troubleshooting need where the LMTD method is cumbersome.

Key ideas

  • A heat exchanger transfers energy between two fluid streams through a wall. We analyze it assuming steady state, negligible heat loss to surroundings, no internal heat generation, constant properties, and a uniform overall heat transfer coefficient U over the area A.
  • Define capacity (heat capacity) rates: Capacity rate C of a fluid is C = ṁ · cp (W/K), where ṁ is mass flow rate and cp is specific heat at constant pressure.
  • The smaller of the two capacity rates is Cmin and the larger is Cmax. The capacity ratio is Cr = Cmin / Cmax (0 ≤ Cr ≤ 1). Many limits and formulas use Cr.
  • The largest possible heat transfer between the two streams, if one stream could be cooled/heated all the way to the inlet temperature of the other, is qmax = Cmin · (Th,in − Tc,in).
  • Effectiveness ε is the fraction of the maximum possible heat transfer actually achieved: ε = q / qmax. By definition, 0 ≤ ε ≤ 1.
  • Number of Transfer Units (NTU) measures heat transfer area relative to the minimum capacity rate: NTU = U · A / Cmin. It is dimensionless. Larger NTU usually means larger area or larger U and thus higher effectiveness.
  • Why NTU method: In design/sizing problems, outlet temperatures are unknown, but U and A (or U and target ε) are specified/estimated. The NTU–ε relations provide q and outlet temperatures directly from NTU and Cr without solving coupled energy differential equations for each configuration.

Assumptions (unless stated otherwise):

  • Steady state, no heat loss to surroundings (adiabatic external surface).
  • No axial (streamwise) conduction in fluids or wall; negligible kinetic/potential energy changes.
  • Constant cp, constant U over the area, uniform flow distribution.
  • No phase change unless using the special Cr → 0 model.
  • Sign convention: Take q as positive from hot to cold fluid; temperature drops on the hot side and rises on the cold side are positive magnitudes.

Energy balance and outlet temperatures:

  • For any exchanger under the above assumptions: q = Ch (Th,in − Th,out) = Cc (Tc,out − Tc,in).
  • Combine with ε to get q = ε · qmax = ε · Cmin (Th,in − Tc,in); then compute outlets from the energy balance.

Configuration-dependent ε–NTU relations (standard results)

  • Parallel flow (co-current):
    • Exact relation: ε = [1 − exp(−NTU · (1 + Cr))] / (1 + Cr).
    • Limiting behavior: as NTU → ∞, ε → 1 / (1 + Cr) (parallel flow cannot reach ε = 1 unless Cr → 0). For Cr → 0, ε = 1 − exp(−NTU).
  • Counterflow:
    • Exact relation: ε = [1 − exp(−NTU · (1 − Cr))] / [1 − Cr · exp(−NTU · (1 − Cr))].
    • Limiting behavior: as NTU → ∞, ε → 1 for any Cr < 1; for Cr = 1, ε = NTU / (1 + NTU).
    • Counterflow allows temperature cross (Tc,out can exceed Th,out) when Cr < 1 — physically permissible.
  • Crossflow:
    • “Both fluids unmixed” (e.g., finned passages that prevent mixing in both streams):
      • Common correlation: ε = 1 − exp{ − (1/Cr) · [1 − exp(−Cr · NTU)] }.
      • Checks: for Cr → 0, ε → 1 − exp(−NTU). As NTU → ∞, ε → 1 − exp(−1/Cr) (less than unity for finite Cr).
    • “One fluid mixed, other unmixed”:
      • Common correlation: ε = (1/Cr) · [1 − exp{ −Cr · (1 − exp(−NTU)) }].
      • Checks: for Cr → 0, ε → 1 − exp(−NTU); as NTU → ∞, ε → (1/Cr) · [1 − exp(−Cr)] (lower than both-unmixed case).

Special/standard cases:

  • Phase change on one side at essentially constant temperature (e.g., condensing or boiling) corresponds to C → ∞ on that side, hence Cr = 0. In both parallel and counterflow, the effectiveness reduces to ε = 1 − exp(−NTU).
  • Upper bounds:
    • Parallel: εmax = 1 / (1 + Cr) < 1.
    • Counterflow: εmax → 1 for Cr ≤ 1 as NTU → ∞.
    • Crossflow: εmax below counterflow for given Cr and NTU; both-unmixed performs better than one-mixed.

Outline of where ε–NTU relations come from (no derivation details):

  • Start from differential energy balances along the flow direction(s): d(Th − Tc)/dx proportional to local U, perimeter, and inverse of capacity rates.
  • Non-dimensionalize temperatures by (Th,in − Tc,in) and length by NTU; solve the resulting first-order linear ODEs with appropriate boundary conditions for each flow arrangement.
  • Integrate to obtain outlet temperature ratios and hence ε as functions of NTU and Cr.

How real devices differ from ideal models:

  • Property variation with temperature (especially cp, μ, k) and non-uniform U across the area cause deviations.
  • Flow maldistribution, bypassing, leakage in shell-and-tube exchangers reduce effective area (lower ε than predicted).
  • Longitudinal heat conduction in walls (notably in compact exchangers) slightly alters temperature fields.
  • Fouling adds thermal resistance over time, reducing U and thus ε for a fixed A. Allowances (fouling factors) are covered under Heat Exchangers fundamentals.

When to use NTU vs LMTD:

  • NTU is preferred when at least one outlet temperature is unknown and U and A (or U and target ε) are given/assumed (sizing, rating).
  • LMTD is efficient when both outlet temperatures are known or constrained; a correction factor may be needed for mixed configurations. See “Heat exchangers: LMTD method”.

Crossflow “mixed” vs “unmixed” meaning:

  • “Unmixed” means fluid passages prevent mixing normal to the main flow direction (e.g., fins), leading to temperature profiles closer to plug flow.
  • “Mixed” means near-complete mixing normal to heat transfer surface in that stream (e.g., shell-side with few baffles), approximated as uniform bulk temperature in the cross-stream direction.

Formulas

C = ṁ · cp

  • C: capacity rate of a stream (W/K). ṁ: mass flow rate (kg/s). cp: specific heat at constant pressure (J/kg·K). Applies for single-phase fluids with nearly constant cp over the temperature range.

Cmin = min(Ch, Cc), Cmax = max(Ch, Cc), Cr = Cmin / Cmax

  • Ch, Cc: hot- and cold-side capacity rates (W/K). Cr is dimensionless. Applies to all configurations.

qmax = Cmin · (Th,in − Tc,in)

  • qmax: maximum possible heat transfer rate (W). Th,in, Tc,in: inlet temperatures of hot and cold streams (K or °C; use differences in K). Applies generally.

ε = q / qmax

  • ε: effectiveness (dimensionless). q: actual heat transfer rate (W). Applies to all configurations.

NTU = U · A / Cmin

  • NTU: number of transfer units (dimensionless). U: overall heat transfer coefficient (W/m²·K). A: heat transfer area (m²). Applies when U is approximately uniform.

q = ε · Cmin · (Th,in − Tc,in)

  • q: heat transfer rate (W). Use with configuration-specific ε(NTU, Cr).

Th,out = Th,in − q / Ch, Tc,out = Tc,in + q / Cc

  • Outlet temperatures (K or °C). From energy balance assuming no heat loss.

Parallel flow effectiveness: ε = [1 − exp(−NTU · (1 + Cr))] / (1 + Cr)

  • For co-current flow. ε dimensionless; NTU, Cr dimensionless.

Counterflow effectiveness: ε = [1 − exp(−NTU · (1 − Cr))] / [1 − Cr · exp(−NTU · (1 − Cr))]

  • For counter-current flow. ε dimensionless; NTU, Cr dimensionless.

Crossflow, both fluids unmixed: ε = 1 − exp{ − (1/Cr) · [1 − exp(��Cr · NTU)] }

  • For compact finned crossflow where both streams are unmixed. ε dimensionless; NTU, Cr dimensionless.

Crossflow, one fluid mixed and the other unmixed: ε = (1/Cr) · [1 − exp{ −Cr · (1 − exp(−NTU)) }]

  • For crossflow with one stream well mixed transversely. ε dimensionless; NTU, Cr dimensionless.

Special case (Cr → 0, e.g., phase change on one side): ε = 1 − exp(−NTU)

  • Applies to both parallel and counterflow limits when one side has very large capacity rate (or effectively constant temperature).

Invertible forms (use natural log ln):

  • Crossflow, both unmixed: from ε = 1 − exp{ − (1/Cr) [1 − exp(−Cr NTU)] }, define y = exp(−Cr NTU). Then y = 1 + Cr · ln(1 − ε) and NTU = −(1/Cr) · ln[y] (requires y > 0).
  • Crossflow, one mixed: from ε = (1/Cr) [1 − exp{ −Cr (1 − exp(−NTU)) }], define z = exp(−NTU). Then z = 1 + (1/Cr) · ln(1 − Cr ε) and NTU = −ln[z] (requires 0 < 1 − Cr ε ≤ 1).

Worked examples

Example 1 — Direct rating with given UA (counterflow) Given: Counterflow exchanger. Hot water: ṁh = 1.0 kg/s, cph = 4180 J/kg·K, Th,in = 80 °C. Cold water: ṁc = 2.0 kg/s, cpc = 4180 J/kg·K, Tc,in = 20 °C. Overall UA = 8.0 kW/K. Assume: Steady state, no heat loss, constant properties, U uniform.

  1. Capacity rates:
  • Ch = ṁh · cph = 1.0 · 4180 = 4180 W/K
  • Cc = ṁc · cpc = 2.0 · 4180 = 8360 W/K
  • Cmin = 4180 W/K, Cmax = 8360 W/K, Cr = 4180/8360 = 0.50
  1. NTU:
  • NTU = UA / Cmin = (8000 W/K) / (4180 W/K) = 1.913
  1. Effectiveness for counterflow:
  • ε = [1 − exp(−NTU (1 − Cr))] / [1 − Cr · exp(−NTU (1 − Cr))]
  • Compute: (1 − Cr) = 0.5, NTU (1 − Cr) = 0.9565, exp(−0.9565) ≈ 0.384
  • Numerator: 1 − 0.384 = 0.616; Denominator: 1 − 0.5 · 0.384 = 0.808
  • ε ≈ 0.616 / 0.808 = 0.762
  1. Maximum and actual heat transfer:
  • qmax = Cmin (Th,in − Tc,in) = 4180 · (80 − 20) = 4180 · 60 = 250800 W
  • q = ε · qmax = 0.762 · 250800 ≈ 1.912 × 10^5 W = 191 kW
  1. Outlet temperatures:
  • Tc,out = Tc,in + q / Cc = 20 °C + (1.912 × 10^5 W)/(8360 W/K) ≈ 42.9 °C
  • Th,out = Th,in − q / Ch = 80 °C − (1.912 × 10^5 W)/(4180 W/K) ≈ 34.3 °C

Answer: q ≈ 191 kW, Tc,out ≈ 42.9 °C, Th,out ≈ 34.3 °C (temperature cross is permissible in counterflow since Cr < 1).

Example 2 — Sizing area A for a crossflow exchanger (both fluids unmixed) Given: Crossflow (both fluids unmixed) air-to-air exchanger. Hot air: ṁh = 1.2 kg/s, cph = 1007 J/kg·K, Th,in = 120 °C. Cold air: ṁc = 1.5 kg/s, cpc = 1007 J/kg·K, Tc,in = 30 °C. Target cold outlet Tc,out = 70 °C. Overall U = 50 W/m²·K. Find A. Assume: Steady, adiabatic to surroundings, constant properties, U uniform.

  1. Capacity rates and Cr:
  • Ch = 1.2 · 1007 = 1208.4 W/K
  • Cc = 1.5 · 1007 = 1510.5 W/K
  • Cmin = 1208.4 W/K, Cmax = 1510.5 W/K, Cr = 1208.4 / 1510.5 ≈ 0.80
  1. Heat duty from cold-side target:
  • q = Cc (Tc,out − Tc,in) = 1510.5 · (70 − 30) = 1510.5 · 40 = 60420 W
  1. Maximum possible heat transfer and required effectiveness:
  • qmax = Cmin (Th,in − Tc,in) = 1208.4 · (120 − 30) = 1208.4 · 90 = 108756 W
  • εrequired = q / qmax = 60420 / 108756 ≈ 0.556
  1. Find NTU from ε and Cr (crossflow, both unmixed):
  • Use invertible form: ε = 1 − exp{ − (1/Cr) [1 − exp(−Cr · NTU)] }
  • Let y = exp(−Cr · NTU); then y = 1 + Cr · ln(1 − ε)
  • Compute: ln(1 − ε) = ln(1 − 0.556) = ln(0.444) ≈ −0.811
  • y = 1 + 0.80 · (−0.811) ≈ 1 − 0.649 ≈ 0.351
  • NTU = −(1/Cr) · ln(y) = −(1/0.80) · ln(0.351) ≈ 1.31
  1. Area A from NTU:
  • A = NTU · Cmin / U = 1.31 · (1208.4 W/K) / (50 W/m²·K)
  • A ≈ 1.31 · 24.168 m² ≈ 31.6 m²
  1. Hot outlet check (consistency):
  • Th,out = Th,in − q / Ch = 120 °C − (60420 W)/(1208.4 W/K) ≈ 70 °C (consistent with energy balance; both outlets at ~70 °C is acceptable for these rates).

Answer: Required heat transfer area A ≈ 31.6 m² to achieve Tc,out ≈ 70 °C.

Common mistakes

  • Using the wrong ε–NTU formula for the configuration (parallel vs counterflow vs crossflow, and “one fluid mixed” vs “both unmixed”).
  • Forgetting that for counterflow temperature cross is allowed; rejecting correct answers where Tc,out > Th,out.
  • Using degrees Celsius directly in exponential relations is fine because only temperature differences matter — but keep all ΔT in K for consistency and clarity.
  • Using base-10 log instead of natural log when inverting exponential formulas (use ln, not log10).
  • Assuming U is the same for gas–gas and liquid–liquid without checking; U depends strongly on convection coefficients and fouling.
  • Ignoring fouling and property variation in design margins; NTU method gives idealized performance unless fouling resistances are included in U.

For GATE ME

  • Compute effectiveness, heat duty, and outlet temperatures for given ṁ, cp, U, A, and configuration.
  • Given target outlet temperature(s) and U, find required area A (i.e., compute NTU from ε and Cr; for crossflow use the invertible relations or iterate).
  • Compare parallel vs counterflow performance; identify which can achieve a given target with smaller area.
  • Limiting cases: Cr → 0 (phase change), NTU → 0 or large NTU behavior; identify temperature cross conditions.
  • Conceptual: when to use NTU vs LMTD; definitions of ε, NTU, Cr; sign conventions and energy balance checks.
  • Practise:
    • Quick computation of Ch, Cc, Cmin, Cmax, Cr, NTU.
    • Using the exact ε formulas for parallel and counterflow; using crossflow correlations and, when needed, inversion with ln.
    • Checking answers with both-side energy balances for consistency.

Quick check

  1. A counterflow exchanger has Cr = 1 and NTU = 2. What is ε?
  2. In a parallel flow exchanger with Cr = 0.5, what is ε as NTU → ∞?
  3. A condenser (phase change on hot side) has NTU = 1.5. What is ε approximately?

Answers: 1) ε = NTU/(1 + NTU) = 2/3 ≈ 0.667. 2) ε → 1/(1 + Cr) = 1/1.5 ≈ 0.667. 3) For Cr → 0, ε = 1 − exp(−NTU) ≈ 1 − e^(−1.5) ≈ 0.777.

Finished this topic? Mark it so your progress, study plan and readiness keep up.

Stuck on something here?