First Year Engineering is coming soon

We're still writing and reviewing the notes for every subject, and we'll open it when every subject is ready. Meanwhile you can practise aptitude, ask Aria about any subject, or see the branches that are ready.

Special-purpose diodes: LED and photodiode

LEDs (light-emitting diodes) and photodiodes: principles, structures, characteristics, equations (IV, efficiency, responsivity), biasing/modes, and exam-style design/numerical problems.

Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.

Why it matters

Light-emitting diodes (LEDs) and photodiodes convert electrical signals to light and light back to electrical signals. Engineers use them in indicators, optical communication links (like fiber-optic transmitters/receivers), sensors (light meters, proximity), and opto-isolation.

Key ideas

  • Reverse bias: applying voltage that increases the depletion barrier (p-side negative relative to n-side). Very little current flows except a small reverse (leakage) current. In a photodiode, reverse bias improves speed and linearity for light detection.
  • LED (light-emitting diode): a p–n junction diode that emits photons (light) when forward biased due to radiative recombination of electrons and holes in a direct-bandgap semiconductor.
  • Radiative recombination: the process where an electron in the conduction band recombines with a hole in the valence band and releases energy as a photon. Direct bandgap materials (e.g., GaAs, GaN, InGaN, AlGaInP) favor radiative recombination.
  • Electroluminescence: emission of light from a material when an electric current passes through it. In an LED, electroluminescence occurs in the active region of the p–n junction.
  • Internal quantum efficiency (η_int): defined as the ratio of the number of photons generated inside the LED active region to the number of electrons injected. Exact statement: η_int = (rate of radiative recombination) / (rate of total recombination).
  • External quantum efficiency (η_ext): defined as the ratio of the number of photons emitted out of the LED into free space to the number of electrons injected. η_ext < η_int due to optical losses (re-absorption, internal reflection, packaging losses).
  • Wavelength–bandgap relation: Photon energy equals bandgap energy at peak emission: E_ph = h·c/λ ≈ E_g. Thus λ ≈ h·c/E_g. Hence material bandgap determines LED color.
  • LED forward voltage (V_F): the voltage across an LED at a given forward current. Typical at room temperature: IR ≈ 1.2 V, red ≈ 1.8–2.2 V, green ≈ 2.0–3.2 V, blue ≈ 3.0–3.6 V (varies by material and current).
  • Current limiting: LEDs must be driven with a controlled current (series resistor, current source, or driver IC) to prevent thermal runaway and damage.
  • Photodiode: a p–n junction (or PIN structure: p–intrinsic–n) designed to convert incident optical power into electrical current. Under illumination, it generates a photocurrent proportional to incident optical power.
  • Photocurrent (I_L): current generated by absorption of photons creating electron–hole pairs swept by the electric field. Direction is from n to p internally (appears as current flowing out of the photodiode anode under reverse bias).
  • Responsivity (R_λ): defined as the ratio of the photodiode output current to the incident optical power at a given wavelength: R_λ = I_ph / P_in [A/W]. It depends on wavelength and quantum efficiency.
  • Quantum efficiency (η): fraction of incident photons that generate collected carriers. External η includes surface reflection and absorption losses; internal η relates to conversion within the depletion/absorption region.
  • Modes of operation:
    • Photoconductive mode: reverse-biased operation. Wider depletion region and strong electric field reduce junction capacitance and improve speed; current is linearly related to light over a wide range. Dark current and noise increase with reverse bias.
    • Photovoltaic mode: zero-bias operation (solar-cell mode). The device develops an open-circuit voltage under illumination; low noise; used in precision sensing at low frequencies.
  • I–V equation under illumination: For a photodiode, the current equals the normal diode current minus the light-generated current: I = I_S (e^{V/(n·V_T)} − 1) − I_L. Under reverse bias (V < 0 with |V| several V), the exponential term is small and I ≈ −I_L − I_S.
  • Dark current (I_S or I_D): small current that flows in the photodiode under reverse bias with no light. It adds offset and noise.
  • Junction capacitance (C_j): capacitance of the depletion region; decreases with reverse bias. Limits speed together with load resistance (RC time constant).
  • Spectral response: photodiodes respond over a wavelength band set by semiconductor bandgap. Silicon responds roughly from ≈ 400 nm (violet) to ≈ 1100 nm (near-IR), peaking near ≈ 850–950 nm.

Exact statements and derivations commonly asked:

  1. Definition — LED: “A light-emitting diode (LED) is a forward-biased p–n junction diode made of a direct-bandgap semiconductor in which radiative recombination of injected carriers produces photons, resulting in visible or infrared light emission.” Assumptions: low-level injection approximation may not always hold; steady-state operation; temperature approximately constant.
  2. Definition — Photodiode: “A photodiode is a light-sensitive p–n or PIN junction diode that generates a photocurrent proportional to the absorbed optical power; it is usually operated under reverse bias (photoconductive mode) for speed and linearity, or at zero bias (photovoltaic mode) for low noise.” Assumptions: uniform illumination; small-signal linear region when specified.
  3. Derivation — Photodiode I–V under illumination: Start with the diode equation in the dark: I_dark = I_S (e^{V/(n·V_T)} − 1). Light generates a current source I_L in parallel with the diode, directed from n to p, which subtracts from the terminal current. By KCL at the diode terminals, I = I_dark − I_L = I_S (e^{V/(n·V_T)} − 1) − I_L. Under reverse bias with |V| ≫ n·V_T, the exponential term is negligible; hence I ≈ −I_L − I_S ≈ −I_L (since I_L ≫ I_S in typical operation).
  4. Derivation — Responsivity from quantum efficiency: Incident optical power P_in at wavelength λ corresponds to photon flux Φ = P_in / (h·c/λ). If quantum efficiency is η (carriers collected per photon), the photocurrent is I_ph = η·q·Φ = η·q·P_in·λ/(h·c). Therefore, responsivity R_λ = I_ph / P_in = η·q·λ/(h·c). Assumptions: each absorbed photon that contributes is counted once; linear regime without saturation; uniform η over the device at that λ.
  5. Diagram — LED symbol and construction: Draw the standard p–n diode symbol with two small arrows pointing outward from the junction indicating light emission. Label anode (p) and cathode (n). Also sketch a simple package: epoxy dome, reflective cup, semiconductor die on lead frame, bond wire, encapsulant.
  6. Diagram — Photodiode symbol and biasing: Draw diode symbol with two small arrows pointing toward the junction indicating light incidence. Label anode and cathode. Show reverse-bias connection (cathode to positive supply through resistor, anode to ground) for photoconductive mode, with output taken as voltage across the resistor.
  7. Diagram — I–V characteristics: For LED, plot I (y-axis) vs V (x-axis) in forward quadrant with knee at V_F, and negligible reverse current until breakdown. For photodiode, plot I (y-axis) vs V (x-axis) curves for various light levels: at zero light, small dark current; with increasing light, the curves shift downward by I_L; in photoconductive region (reverse bias), current is nearly flat vs V.

Practical notes:

  • LED polarity: the longer lead is usually the anode; the flat edge of 5 mm LEDs marks the cathode. Verify using a multimeter’s diode test. Most LEDs have a low maximum reverse voltage (typically 5 V or less), so avoid reverse-biasing them beyond the datasheet rating.
  • Heat and current: LED light output is roughly proportional to current over a range but decreases with temperature at fixed current. Always limit current with a resistor or a constant-current driver.
  • Photodiode linearity and saturation: At high light levels or low reverse bias, space-charge effects reduce collection efficiency; photocurrent no longer increases linearly with optical power.
  • PIN photodiode: includes an intrinsic layer to widen the depletion region, improving speed and responsivity.

Formulas

I = I_S (e^{V/(n·V_T)} − 1) — Diode I–V relation in the dark; I is diode current (A), V is diode voltage (V), I_S is reverse saturation current (A), n is ideality factor (unitless, ~1–2), V_T is thermal voltage (V) where V_T = k·T/q; applies to a p–n diode without illumination.

I = I_S (e^{V/(n·V_T)} − 1) − I_L — Photodiode I–V under illumination; I is terminal current (A) positive from anode to cathode, I_L is light-generated current (A); applies when illumination adds a current source in parallel with the junction.

V_T = k·T/q — Thermal voltage; k is Boltzmann constant (1.380 649×10⁻²³ J/K), T is absolute temperature (K), q is elementary charge (1.602 176 634×10⁻¹⁹ C); at 300 K, V_T ≈ 25.85 mV.

R_λ = I_ph / P_in — Responsivity definition; R_λ is responsivity (A/W) at wavelength λ, I_ph is photocurrent due to light only (A), P_in is incident optical power at device active area (W); applies in linear region.

R_λ = η·q·λ/(h·c) — Responsivity from quantum efficiency; η is quantum efficiency (unitless), q is charge (C), λ is wavelength (m), h is Planck’s constant (6.626 070 15×10⁻³⁴ J·s), c is speed of light in vacuum (≈3.00×10⁸ m/s); applies when each collected carrier pair corresponds to one photon.

E_ph = h·c/λ — Photon energy; E_ph (J), λ (m); used to relate LED color (wavelength) to bandgap energy. Equivalently, using common exam units: E_g (eV) ≈ 1240/λ (nm).

P_opt ≈ η_ext·I·(h·c/λ)/q — Approximate LED optical output power; P_opt (W), η_ext external quantum efficiency (unitless), I is forward current (A); assumes each electron contributes with probability η_ext.

R_S = (V_SUP − V_F − V_LED_DRIVER_MARGIN)/I_F — Series resistor for LED from a DC supply; R_S (Ω), V_SUP supply (V), V_F LED forward voltage at desired current I_F (V), margin term is 0 if no driver headroom is needed; applies when using a simple resistor to set current.

f_−3dB ≈ 1/(2·π·R_L·C_j) — Approximate bandwidth limit of a reverse-biased photodiode with load; f_−3dB (Hz), R_L load resistance seen by the diode (Ω), C_j junction capacitance (F); applies to small-signal RC-limited response.

V_OC ≈ n·V_T·ln(1 + I_L/I_S) — Photovoltaic open-circuit voltage; V_OC (V); applies to a photodiode/solar cell at open circuit under illumination.

Worked examples

Example 1 — LED series resistor design for an indicator Given: 5.0 V DC supply, one red LED with V_F = 2.0 V at I_F = 15 mA desired. Find the series resistor value and its power rating.

Steps:

  1. Use R_S = (V_SUP − V_F)/I_F.
  2. Substitute numbers: R_S = (5.0 V − 2.0 V) / 15 mA = 3.0 V / 0.015 A = 200 Ω.
  3. Choose the nearest standard value ≥ 200 Ω to limit current slightly; 220 Ω is common.
  4. Power in resistor: P_R = I_F²·R_S = (0.015 A)²·200 Ω = 0.000225 A²·200 Ω = 0.045 W.
  5. Use a resistor with margin, at least 0.25 W.

Answer: Use R_S ≈ 200 Ω (220 Ω preferred standard). Minimum resistor rating ≈ 0.045 W; select a 0.25 W resistor for safety. Final current with 220 Ω: I ≈ (5.0 − 2.0)/220 ≈ 13.6 mA.

Example 2 — Photodiode photocurrent and output voltage in reverse bias A silicon photodiode (reverse-biased) has responsivity R_λ = 0.45 A/W at 850 nm and dark current I_S ≈ 2 nA at the chosen reverse bias. Incident optical power on the active area is P_in = 100 µW. The diode is connected with a load resistor R_L = 100 kΩ to +5 V (cathode to +5 V through R_L, anode to ground), and the output is the voltage across R_L (measured as the drop from +5 V to the photodiode cathode node).

Steps:

  1. Photocurrent: I_ph = R_λ·P_in = 0.45 A/W · 100×10⁻⁶ W = 45 µA.
  2. Total current through R_L is approximately the sum of photocurrent and dark current (they flow from supply through R_L into the diode to ground). Magnitude I_total ≈ I_ph + I_S ≈ 45 µA + 0.002 µA ≈ 45.002 µA ≈ 45 µA (dark current negligible).
  3. Voltage across R_L: V_out = I_total·R_L = 45 µA · 100 kΩ = 4.5 V. Check supply headroom: 4.5 V < 5 V, so operation is linear; the diode remains reverse-biased (about 0.5 V across it if referenced to ground through R_L and supply).

Answer: Photocurrent ≈ 45 µA; output voltage across R_L ≈ 4.5 V (reverse-biased, linear region).

Example 3 — Responsivity from quantum efficiency and wavelength A photodiode has external quantum efficiency η = 0.70 at λ = 900 nm. Find responsivity R_λ.

Steps:

  1. Use R_λ = η·q·λ/(h·c).
  2. Substitute: q = 1.602×10⁻¹⁹ C, λ = 900 nm = 900×10⁻⁹ m, h = 6.626×10⁻³⁴ J·s, c = 3.00×10⁸ m/s.
  3. Compute numerator: η·q·λ = 0.70 · 1.602×10⁻¹⁹ C · 900×10⁻⁹ m = 0.70 · 1.4418×10⁻²⁵ C·m ≈ 1.0093×10⁻²⁵ C·m.
  4. Denominator: h·c = 6.626×10⁻³⁴ · 3.00×10⁸ = 1.9878×10⁻25 J·m (≈ 1.986×10⁻25 J·m for easier calc). Use 1.9878×10⁻25 J·m.
  5. Divide: R_λ ≈ (1.0093×10⁻²۵) / (1.9878×10⁻²۵) A/W ≈ 0.508 A/W.

Answer: Responsivity at 900 nm ≈ 0.51 A/W.

Model answer sketch — Construction and working of LED and photodiode with characteristics

  • LED construction: Chip of direct-bandgap material (e.g., GaAsP for red, InGaN for blue) mounted on reflective cup; wire-bonded to leads; encapsulated in epoxy or silicone lens for light extraction. Active p–n junction region near the surface to reduce re-absorption.
  • LED working: Under forward bias, electrons from n-side and holes from p-side are injected across the junction. Radiative recombination in the active region emits photons. Peak emission wavelength is set by bandgap. I–V is exponential with a knee voltage V_F depending on current and temperature (V_F decreases roughly 2 mV/°C for many LEDs). Light output approximately proportional to forward current over a specified range.
  • Photodiode construction: PIN structure commonly used. The intrinsic layer increases depletion width, improving quantum efficiency and reducing capacitance. Anti-reflection coating may be present to improve η. Package may include a window and optical filter.
  • Photodiode working: Under reverse bias, the electric field sweeps photogenerated carriers quickly, giving a photocurrent proportional to optical power. I–V characteristics: in dark, small reverse current; with illumination, reverse current increases by I_L nearly independent of V until high fields cause avalanche or saturation.
  • Characteristics to plot and label: LED — I vs V (forward region) and relative radiant intensity vs current; Photodiode — I vs V at different light levels, marking photoconductive and photovoltaic regions; Responsivity vs wavelength curve peaking in near-IR for Si.

Common mistakes

  • Using LED forward voltage values from a datasheet at one current for a different current without checking the V–I curve and temperature coefficient.
  • Assuming photodiode current depends on reverse voltage linearly; in the photoconductive region, photocurrent is almost independent of reverse voltage over a range.
  • Forgetting dark current and saturation effects, leading to overestimation of linear measurement range.
  • Confusing responsivity (A/W) with quantum efficiency (unitless) and with spectral irradiance units.
  • Neglecting RC bandwidth limits from junction capacitance and load resistance in photodiode circuits.

For your exam

Expect:

  • Definitions: LED, electroluminescence, photodiode, responsivity, quantum efficiency, dark current, photovoltaic vs photoconductive mode.
  • Short notes: LED materials and colors, PIN photodiode, spectral response of Si photodiode, packaging and light extraction, LED temperature effects.
  • Diagrams: LED and photodiode symbols with arrows and terminals; internal construction sketches; I–V characteristic curves for illuminated and dark conditions; simple LED biasing with series resistor; photodiode reverse-bias readout with resistor or transimpedance amplifier.
  • Derivations: Photodiode I–V under illumination; Responsivity R_λ = η·q·λ/(h·c); Relation between λ and bandgap energy E_g = h·c/λ.
  • Numericals: LED resistor and power rating from supply; Photodiode photocurrent and output voltage for a given P_in and R_L; Responsivity from η and λ; Bandwidth from R and C_j. Full-marks answers include: clear definitions, labeled diagrams, correct formulas with units, assumptions stated (e.g., linear region, constant temperature), step-by-step calculations with units, and a concise conclusion.

Quick check

  1. State the I–V equation of a photodiode under illumination and define each term.
  2. A silicon photodiode has η = 0.8 at 1000 nm. Estimate its responsivity.
  3. Why is reverse bias used in photoconductive mode of a photodiode?

Answers: 1) I = I_S (e^{V/(n·V_T)} − 1) − I_L, where I is terminal current (A), V is diode voltage (V), I_S is saturation current (A), n is ideality factor, V_T = kT/q is thermal voltage (V), I_L is light-generated current (A). 2) R_λ ≈ η·q·λ/(h·c) ≈ 0.8·1.602e−19·1.0e−6/(6.626e−34·3.0e8) ≈ 0.64 A/W. 3) Reverse bias widens the depletion region and strengthens the electric field, reducing capacitance and carrier transit time, improving speed and linearity while making photocurrent nearly independent of voltage over a range.

Finished this topic? Mark it so your progress, study plan and readiness keep up.

Stuck on something here?