Artificial Intelligence & Data Science is coming soon

We're still writing and reviewing the notes for every subject, and we'll open it when every subject is ready. Meanwhile you can practise aptitude, ask Aria about any subject, or see the branches that are ready.

Interference in thin films

Interference in thin films: phase change on reflection, path difference 2·n·t·cos r, conditions for bright/dark in reflected/transmitted light, wedge fringes, Newton’s rings, and anti-reflection coatings.

Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.

Why it matters

Key ideas

  • Phase change on reflection (π-shift rule): When light reflects from an interface going from a medium of lower refractive index to higher refractive index, the reflected wave suffers a phase reversal of π (equivalent to an extra path of λ/2). Reflection from higher to lower refractive index produces no phase reversal. Transmission never causes such jump; it only accumulates phase from propagation through thickness.
  • Geometry and angles: Light of angle of incidence i enters the film at angle of refraction r, related by Snell’s law n₁·sin i = n₂·sin r. Inside the film, the optical path difference between the two main reflected (or transmitted) rays is governed by the double pass 2·n·t·cos r.

Exact statements and standard derivations

  1. Condition for interference in a uniform thin film (two-beam model)
  • Assumptions: monochromatic, coherent light; transparent, non-absorbing film of refractive index n and thickness t; smooth, plane-parallel interfaces; multiple higher-order internal reflections are neglected (two-beam approximation, valid for weak reflectance). Air outside has n ≈ 1.
  • Path difference: The second reflected ray traverses down and up inside the film. The physical path length inside the film is 2·t/ cos r along the ray, but after accounting for the equalization of emerging rays the net optical path difference is OPD = 2·n·t·cos r (measured relative to vacuum/air wavelength λ₀).
  • Phase reversal term: Add an extra λ₀/2 to the OPD when there is exactly one phase reversal among the two interfering reflected rays (i.e., one reflection occurs from a lower-to-higher index and the other from higher-to-lower). If there are zero or two reversals, do not add λ₀/2.

Reflected light (two-beam):

  • Constructive (bright): • If one phase reversal: 2·n·t·cos r = (m + 1/2)·λ₀, m = 0, 1, 2, … • If zero or two reversals: 2·n·t·cos r = m·λ₀.
  • Destructive (dark): opposite of the above cases.

Transmitted light (two-beam):

  • Constructive (bright): • If one phase reversal at reflection: 2·n·t·cos r = m·λ₀. • If zero or two reversals: 2·n·t·cos r = (m + 1/2)·λ₀.
  • Note: “Opposite” conditions arise because the reflected pair and transmitted pair differ in their relative phase by π when energy is conserved in a lossless film.

What to draw (uniform film at oblique incidence):

  • Draw two horizontal parallel lines as film boundaries. Label top medium n₁, film n, bottom medium n₃. Show incident ray at angle i to the normal, refracted ray inside at angle r, using a normal line to the interfaces. Mark two reflected rays: one from top interface and one returning from bottom. Label thickness t, angle r inside film, and indicate the extra optical path 2·n·t·cos r. Add a note: “π phase shift at reflection from lower to higher n.”
  1. Wedge-shaped film and straight fringes
  • Wedge-shaped film: Two surfaces enclosing a small angle α (in radians), forming a film whose thickness increases linearly along x: for small α, t(x) ≈ x·α.
  • Typical setup: Two glass plates with a spacer at one end create an air wedge (n ≈ 1). Light is incident nearly normal; fringes are localized near the wedge and appear as straight, equally spaced dark and bright bands parallel to the line of contact.
  • Phase reversal: For an air wedge between glass plates, reflection at the top glass–air interface (viewed from air) involves lower-to-higher index at the first reflecting surface of the thin air film, and higher-to-lower at the second; net is one phase reversal for the two reflected rays. Hence, in reflected light, there is a dark fringe at the contact (t = 0).
  • Conditions (normal incidence, air film): • Dark (reflected): 2·t = m·λ (here λ ≈ λ₀ in air), m = 0, 1, 2, … • Bright (reflected): 2·t = (m + 1/2)·λ.
  • Fringe spacing (interfringe distance β): Using t = x·α and the dark condition, successive dark fringes at positions x_m satisfy 2·x_m·α = m·λ, so β = x_{m+1} − x_m = λ/(2·α), approximately constant for small α.

What to draw (wedge):

  • Two long plates making a small angle α. Mark a thin spacer at one end. Show incident light and two reflected rays. Draw straight fringes parallel to the contact. Label t = x·α and indicate that the first dark fringe occurs at contact (x = 0).
  1. Newton’s rings (circular fringes)
  • Setup: A plano-convex lens of large radius of curvature R placed on a flat glass plate forms a thin air film of varying thickness between them. Illumination is typically with monochromatic, collimated light, observed in reflection (dark center) or transmission (bright center for the same order).
  • Geometry: For distance r from the point of contact, the thickness of the air film is t ≈ r²/(2·R) (lens sagitta formula, valid when r ≪ R).
  • Reflected-light conditions (one phase reversal): • Dark rings: 2·t = m·λ ⇒ r_m² = m·λ·R, m = 0, 1, 2, … (m = 0 gives dark center) • Bright rings: 2·t = (m + 1/2)·λ ⇒ r_m² = (m + 1/2)·λ·R
  • Diameters: D_m² = 4·m·λ·R (dark), and D_m² = 4·(m + 1/2)·λ·R (bright).
  • In transmitted light, bright and dark conditions interchange.

What to draw (Newton’s rings):

  • A plano-convex lens resting on a flat plate. Show circular fringes centered at contact. Label R (radius of curvature), r (radial distance), and t = r²/(2·R). Indicate dark center in reflection.
  1. Anti-reflection coating (quarter-wave film)
  • Goal: Minimize reflected intensity at a design wavelength λ₀ for light from air onto a high-index substrate.
  • Common design: A single-layer film of refractive index n_f between air (≈1) and substrate n_s, with n_s > n_f > 1, and thickness t = λ₀/(4·n_f).
  • Reason: Reflections from the air–film and film–substrate interfaces have equal π phase reversals (two in total, net zero), but the extra optical path inside the film makes them out of phase by π when 2·n_f·t = λ₀/2. Amplitude matching is optimized when n_f ≈ √(n_air·n_s).

Other notes

  • White-light illumination produces colored patterns because the bright/dark conditions depend on wavelength; different wavelengths satisfy conditions at different thicknesses.
  • At oblique incidence, always use cos r (inside-film angle), not cos i.
  • Multi-beam effects (Fabry–Pérot) produce sharper fringes when reflectivity is high; this note focuses on the standard two-beam model unless stated.

Formulas

  • OPD = 2·n·t·cos r — optical path difference from double pass inside film of index n and thickness t (m), for internal angle r (radians). Two-beam approximation.
  • Reflected-light conditions (two-beam): • With one phase reversal: 2·n·t·cos r = (m + 1/2)·λ₀ (bright), 2·n·t·cos r = m·λ₀ (dark); m = 0, 1, 2, … • With zero or two reversals: 2·n·t·cos r = m·λ₀ (bright), 2·n·t·cos r = (m + 1/2)·λ₀ (dark).
  • Transmitted-light conditions (two-beam): opposite to reflected-light conditions given above.
  • Wedge thickness: t(x) ≈ x·α — small-angle wedge with wedge angle α (radians) along distance x (m) from contact.
  • Wedge interfringe spacing (reflected, air film, near-normal incidence): β = λ / (2·α) — β (m) is distance between successive dark (or bright) fringes.
  • Newton’s rings thickness: t = r² / (2·R) — r is ring radius (m), R is lens radius of curvature (m).
  • Newton’s rings (reflected): r_m² = m·λ·R for dark rings; r_m² = (m + 1/2)·λ·R for bright rings. Diameters: D_m² = 4·m·λ·R (dark).
  • Quarter-wave anti-reflection thickness: t = λ₀ / (4·n_f) — n_f is coating index (dimensionless). Best amplitude match when n_f ≈ √(n_s) for n_air ≈ 1.

Constants

  • Speed of light in vacuum: c = 2.99792458 × 10⁸ m·s⁻¹ (exact, SI definition).

Worked examples

Example 1: Minimum thickness for anti-reflection at normal incidence

  • Given: Glass substrate n_s = 1.52, coating MgF₂ with n_f = 1.38, design wavelength λ₀ = 550 nm, normal incidence (r = 0, cos r = 1).
  • Required: Minimum thickness t for zero reflection at λ₀.
  • Formula: t = λ₀ / (4·n_f).
  • Steps:
    1. Substitute values: t = (550 × 10⁻⁹ m) / (4 × 1.38).
    2. Compute denominator: 4 × 1.38 = 5.52.
    3. t = 550e−9 / 5.52 m = 99.64 × 10⁻⁹ m.
  • Answer: t = 9.964 × 10⁻⁸ m ≈ 100 nm (minimum thickness) — bold: 1.00 × 10⁻⁷ m.

Example 2: Fringe spacing in an air wedge

  • Given: Monochromatic light λ = 589 nm (sodium D-line), wedge angle α = 0.050°, normal incidence; air film so n ≈ 1.
  • Required: Interfringe spacing β between successive dark fringes in reflected light.
  • Convert α to radians: α = 0.050° × (π/180) = 8.7266 × 10⁻⁴ rad (approx.).
  • Formula: β = λ / (2·α).
  • Steps:
    1. β = (589 × 10⁻⁹ m) / (2 × 8.7266 × 10⁻⁴).
    2. Denominator = 1.74532 × 10⁻³.
    3. β = 589e−9 / 1.74532e−3 m = 3.376 × 10⁻⁴ m.
  • Answer: β = 3.38 × 10⁻⁴ m ≈ 0.338 mm.

Example 3: Diameter of the 10th dark Newton’s ring (reflected light)

  • Given: λ = 546 nm (green mercury line), radius of curvature R = 1.00 m. Find diameter D₁₀ of the 10th dark ring in reflected light.
  • Formula: D_m² = 4·m·λ·R (for dark rings in reflection).
  • Steps:
    1. D₁₀² = 4 × 10 × (546 × 10⁻⁹ m) × (1.00 m) = 21.84 × 10⁻⁶ m² = 2.184 × 10⁻⁵ m².
    2. D₁₀ = √(2.184 × 10⁻⁵) m.
    3. Compute: √2.184 ≈ 1.478; √10⁻⁵ = 3.162 × 10⁻³.
    4. D₁₀ ≈ 1.478 × 3.162 × 10⁻³ m = 4.67 × 10⁻³ m.
  • Answer: D₁₀ = 4.67 × 10⁻³ m = 4.67 mm.

Common mistakes

  • Confusing order numbering m: whether m = 0 corresponds to the central dark or bright fringe depends on phase reversal and on whether observing reflection or transmission (e.g., Newton’s rings have a dark center in reflection).
  • Ignoring small-angle approximations’ limits: t ≈ x·α and t ≈ r²/(2·R) are valid only for small α and r ≪ R.
  • Forgetting that in an air wedge (reflected light) the contact is dark (t = 0), not bright.
  • For anti-reflection coatings, forgetting the amplitude condition n_f ≈ √(n_s), which affects residual reflectance even if thickness is correct.

For your exam

  1. Derive OPD = 2·n·t·cos r and obtain conditions for maxima/minima in reflected light for (i) one phase reversal and (ii) zero/two phase reversals.
  2. Wedge fringes: derive β = λ/(2·α) and explain why the fringe at contact is dark in reflection.
  3. Newton’s rings: derive r_m² = m·λ·R and D_m² = 4·m·λ·R for reflected light. Comment on transmitted light.
  4. Anti-reflection coating: derive t = λ₀/(4·n_f) and n_f ≈ √(n_s) for minimal reflectance at λ₀.
  • Diagrams: neat, large, with normals and angles labelled; show ray paths, thickness t, angles i and r, and indicate where phase reversal occurs. For Newton’s rings, show the lens–plate contact and circular fringes.
  • Numericals: carry units throughout, convert degrees to radians for α, and be explicit about whether λ or λ₀ is used. State assumptions (normal incidence, air film, two-beam approximation, small-angle approximations) before solving.
  • Short notes: colors in soap films with white light; effect of oblique incidence; difference between reflected and transmitted patterns.

Quick check

  1. In a uniform film of index n at angle r inside the film, what OPD enters the interference condition? State also when you must add λ₀/2.
  2. For Newton’s rings in reflected light, is the central spot bright or dark, and why?
  3. A single-layer AR coating of index n_f is deposited on glass (n_s). What thickness minimizes reflection at λ₀, and what index n_f gives best cancellation of amplitudes?

Answers: (1) OPD = 2·n·t·cos r; add λ₀/2 when there is exactly one phase reversal between the two reflected rays. (2) Dark, because at t = 0 there is one phase reversal in reflection, giving destructive interference. (3) t = λ₀/(4·n_f); optimal n_f �� √(n_s) for air–film–substrate.

Finished this topic? Mark it so your progress, study plan and readiness keep up.

Stuck on something here?