SUK TY Mechanical syllabus

SUK · Third Year B.Tech. Mechanical Engineering · NEP 2020

Design of Machine Elements

ME0251 · Semester V · 3 credits · ISE 10 + mid-semester 30 + ESE 60

  1. Unit 1: Fundamentals of Machine Design and Design against Static Load

    6 hours

    Machine design, types of loads, factor of safety and its selection, phases of design; the role of AI in product design and manufacturing; theories of failure and their selection.

    Examined in the 60-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • The machine design process
    • Material selection and factor of safety
    • Theories of failure in design
  2. Unit 2: Design against Fluctuating Load

    8 hours

    Stress concentration, its causes and remedies; fluctuating stresses, the S–N diagram, endurance limit, notch sensitivity and modifying factors; design for finite and infinite life, cumulative damage, Goodman and modified Goodman diagrams.

    Examined in the 60-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Stress concentration
    • Fatigue, S–N curve and endurance limit
    • Soderberg, Goodman and Gerber criteria
    • Finite life and cumulative damage
  3. Unit 3: Design of Shafts, Keys and Springs

    6 hours

    Solid and hollow shafts and the ASME code; types of keys and the flat key; types of springs, end styles and helical compression springs under static load.

    Examined in the 60-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Design of shafts for strength
    • Design of shafts for rigidity and the ASME code
    • Design of keys and splines
    • Design of helical springs
  4. Unit 4: Design of Joints and Couplings

    6 hours

    Knuckle joint; types of couplings and the rigid coupling; bolted joints in shear and under load perpendicular to the bolt axis; transverse and parallel fillet welds, eccentric loads and welds under bending.

    Examined in the 60-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Cotter and knuckle joints
    • Design of flange couplings
    • Eccentrically loaded bolted joints
    • Strength of welded joints
    • Eccentrically loaded welded joints
  5. Unit 5: Design of Bearings

    6 hours

    Rolling contact bearings: static and dynamic capacity, Stribeck's equation, equivalent load, load–life relation and selection from catalogues, variable load and speed, lubrication and mounting; hydrodynamic sliding bearings, Reynolds equation and the Raimondi–Boyd method.

    Examined in the 60-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Types of rolling contact bearings
    • Static and dynamic load capacity
    • Equivalent load and bearing life
    • Selecting bearings from a catalogue
    • Hydrodynamic sliding bearings
  6. Unit 6: Design of Gears

    6 hours

    Gear failures; spur gear force analysis, Lewis beam strength, Barth, Spott's and Buckingham dynamic load and wear strength; helical and bevel gears: formative teeth, forces, beam and wear strength; worm gearing as per IS 7443.

    Examined in the 60-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Gear materials and modes of tooth failure
    • Spur gear force analysis
    • Beam strength: the Lewis equation
    • Wear strength and dynamic load: Buckingham's equation
    • Design of helical gears
    • Straight bevel gears
    • Worm gear terminology and force analysis

Unit contents are summarised from the official SUK syllabus . AiCanCode.org is not affiliated with Shivaji University, Kolhapur.