PAHSU SY Civil syllabus

PAHSU · Second Year B.Tech. Civil Engineering · NEP 2020

Fluid Mechanics and Fluid Machines

CIVPCC-02 · Semester III · 3 credits · ISE 30 + ESE 70

  1. Unit 1: Fluid Properties

    5 hours

    Density, specific weight, specific volume and relative density; cohesion and adhesion; viscosity, Newtonian and non-Newtonian fluids; compressibility, surface tension, capillarity, vapour pressure and cavitation.

    Examined in the 70-mark end-semester paper

    • Properties of fluids
    • Viscosity and Newton's law of viscosity
    • Surface tension and capillarity
  2. Unit 2: Fluid Statics

    8 hours

    Pascal's law and the hydrostatic law; pressure measurement with piezometers, U-tube and differential manometers and the Bourdon gauge; total pressure and centre of pressure on vertical and inclined plane surfaces; buoyancy, metacentre and metacentric height, equilibrium of floating and submerged bodies.

    Examined in the 70-mark end-semester paper

    • Pressure and its measurement
    • Total pressure and centre of pressure
    • Buoyancy and metacentric height
  3. Unit 3: Fluid Kinematics and Dynamics

    8 hours

    Describing fluid motion, control volume, streamlines, path lines, streak lines and types of flow; continuity equation, velocity potential, stream function and flow nets; Euler's equation along a streamline and Bernoulli's theorem; discharge by venturimeter, orifice meter and orifice; velocity by Pitot tube.

    Examined in the 70-mark end-semester paper

    • Types of flow and flow lines
    • Continuity equation
    • Velocity potential and stream function
    • Flow nets
    • Euler's equation and Bernoulli's equation
    • Venturimeter and orifice meter
    • Pitot tube and rotameter
    • Orifices and mouthpieces
  4. Unit 4: Notches and Weirs

    5 hours

    Types of notches, discharge equations, velocity of approach, Francis formula and errors in head measurement; sharp- and broad-crested weirs, calibration, time to empty a tank, ventilation of weirs and types of nappe.

    Examined in the 70-mark end-semester paper

    • Notches and weirs
  5. Unit 5: Flow Through Pipes and Boundary Layer

    7 hours

    Major and minor losses, the Darcy-Weisbach equation, pipes in series and parallel, equivalent length and diameter, HGL and TEL, siphons and water hammer; pipe networks by the Hardy Cross method; development of the boundary layer on a flat plate, laminar sub-layer, displacement, momentum and energy thickness, hydrodynamically smooth and rough boundaries.

    Examined in the 70-mark end-semester paper

    • Turbulent flow and Darcy–Weisbach equation
    • Minor losses in pipes
    • Pipes in series and parallel
    • Hydraulic gradient and energy lines
    • Siphons, water hammer and power through nozzles
    • Pipe networks: Hardy Cross method
    • Boundary layer theory and separation
  6. Unit 6: Impact of Jets, Hydraulic Turbines and Pumps

    9 hours

    Force and work done by a jet on stationary and moving flat and curved plates; elements of a hydropower plant; classification of turbines, Francis and Kaplan turbines, draft tubes, specific speed, the Pelton wheel, unit and specific quantities and turbine selection; centrifugal pumps: components, velocity triangles, heads and efficiencies, priming and multistage pumps; submersible and reciprocating pumps and pump selection.

    Examined in the 70-mark end-semester paper

    • Impact of jet on flat plates
    • Impact of jet on curved vanes
    • Hydroelectric power plant layout
    • Hydraulic turbines: types, efficiency and specific speed
    • Pelton wheel
    • Francis and Kaplan turbines
    • Draft tubes and cavitation
    • Centrifugal pumps
    • Reciprocating pumps
    • Jet, air-lift and submersible pumps

Unit contents are summarised from the official PAHSU syllabus . AiCanCode.org is not affiliated with Punyashlok Ahilyadevi Holkar Solapur University (PAHSU).