GUG TY Mechanical syllabus

GUG · Third Year B.Tech. Mechanical Engineering · NEP 2020

Internal Combustion Engines and Gas Turbines

STPECMEC506A · Program Elective I · Semester V · 3 credits · IE 10 + mid-semester 10 + ESE 80

One of the Program Elective I options.

  1. Unit 1: IC Engines and Their Fuels

    9 hours

    Energy conversion, components and nomenclature, working principles and classification of IC engines; SI and CI engines compared; valve timing diagrams, applications and performance parameters; petrol and diesel, octane and cetane ratings; LPG, CNG, ethanol and biodiesel and its preparation.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • IC engine classification and components
    • Two-stroke and four-stroke engines
    • Valve timing diagrams
    • Engine performance parameters
    • Alternative fuels and fuel ratings
    • Biodiesel and transesterification
  2. Unit 2: Fuel Supply, Lubrication, Cooling and Ignition

    9 hours

    Carburettors and air-fuel ratio, MPFI and port injection; DI, CRDI, distributor and individual-pump systems, fuel pumps and injectors; lubrication requirements and systems; heat rejection, air and water cooling; ignition systems and spark advance.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Simple carburettor and its circuits
    • Multipoint and direct injection in SI engines
    • Fuel injection in SI and CI engines
    • CRDI and variable geometry turbochargers
    • Fuel injection pumps, governors and nozzles
    • Lubrication systems
    • Cooling systems
    • Ignition systems
  3. Unit 3: Combustion in SI and CI Engines

    9 hours

    Normal combustion and its stages in SI engines, combustion chamber design, pre-ignition, flame propagation, detonation and knock, turbulence, swirl, squish and tumble; combustion in DI and IDI CI engines, fuel sprays, ignition delay and diesel knock; supercharging, turbocharging and scavenging.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Combustion in SI engines and knock
    • Combustion chambers
    • Combustion in CI engines and knock
    • Diesel spray behaviour, penetration and air motion
    • Supercharging and turbocharging
  4. Unit 4: Engine Testing and Emissions

    9 hours

    Measuring indicated, brake and friction power, speed, fuel and air consumption; the Morse test, Willan's line and motoring test; thermal, volumetric and mechanical efficiencies; the heat balance sheet and performance curves; SI and CI engine emissions and their control, Euro and Bharat Stage norms, health effects.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Measuring friction power: Willan's line and Morse test
    • Heat balance sheet
    • Pollutant formation: CO, HC, NOx and particulates
    • Engine emissions and their control
    • Emission measurement, norms and driving cycles
  5. Unit 5: Gas Turbines and Jet Propulsion

    9 hours

    Ideal gas turbine cycles, isentropic and stage efficiencies, pressure losses; intercooling, reheating and regeneration; fuel-air ratio and combustion efficiency; open and closed cycles, cogeneration and combined cycles; turbojet, turboprop, ramjet and pulsejet, thrust and propulsive power and efficiencies.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Brayton cycle
    • Gas turbine cycles: intercooling, reheating and regeneration
    • Open- and closed-cycle gas turbines
    • Combined cycle and cogeneration
    • Jet propulsion: turbojet, turboprop, ramjet and pulse jet

Unit contents are summarised from the official GUG syllabus . AiCanCode.org is not affiliated with Gondwana University, Gadchiroli.