GUG SY Mechanical syllabus

GUG · Second Year B.Tech. Mechanical Engineering · NEP 2020

Manufacturing Processes

STPCCMEC405 · Semester IV · 3 credits · IE 10 + mid-semester 10 + ESE 80

  1. Unit 1: Theory of Metal Cutting

    8 hours

    Single- and multi-point, orthogonal and oblique cutting; force components and Merchant's circle; chip formation and types of chips; tool nomenclature and deformation zones; tool wear and tool life, surface finish and integrity, machinability, tool materials and cutting fluids.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Orthogonal and oblique cutting
    • Merchant's theory and cutting forces
    • Chip formation and types of chips
    • Single-point cutting tool geometry
    • Tool wear and Taylor's tool life equation
    • Cutting tool materials and tool signature
    • Machinability and cutting fluids
  2. Unit 2: Casting and Moulding

    8 hours

    Patterns, pattern materials, allowances and types, core prints; moulding processes including injection and blow moulding; moulding sand and its properties, melting furnaces and the cupola, mechanised foundries; gating design, aspiration, gating ratio and directional solidification; sand, centrifugal, continuous, die, investment, shell, slush and CO2 casting; casting defects and remedies.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Patterns and pattern allowances
    • Moulding sand and cores
    • Melting furnaces: cupola, crucible, arc and induction
    • Gating system and mould filling time
    • Riser design and solidification
    • Special casting processes
    • Casting defects and remedies
    • Polymer moulding processes
  3. Unit 3: Mechanical Working of Metals

    8 hours

    Hot and cold working; rolling, its parameters and rolling mills; hot and cold forging, direct and indirect extrusion and roll forging; sheet-metal work: spinning, formability, deep drawing, wire drawing, bending, blanking, piercing, swaging, hobbing and embossing; mechanical and hydraulic presses.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Fundamentals of metal forming
    • Rolling and rolling load
    • Forging and forging load
    • Extrusion, wire and tube drawing
    • Sheet metal operations and presses
    • Deep drawing and blank development
    • Formability and forming-limit diagrams
  4. Unit 4: Welding Processes

    8 hours

    AC and DC welding, electrode classification and coding, the physics of welding, brazing and soldering, weld joints; classification of welding processes, defects and their remedies, the heat-affected zone; gas, arc, electron beam, laser beam, ultrasonic, thermit, GTAW, GMAW, SMAW, resistance and plasma welding.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Gas welding and flames
    • Arc welding: MIG and TIG
    • Resistance welding
    • Solid-state and modern welding processes
    • Soldering, brazing and weld joints
    • Welding defects and inspection
  5. Unit 5: Unconventional Machining Processes

    8 hours

    Principles and process parameters of abrasive jet, abrasive water jet and ultrasonic machining, EDM, ECM, laser beam, plasma arc and electron beam machining; material removal rate, surface finish and tool wear.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Classification of modern machining processes
    • Abrasive jet machining
    • Abrasive water jet machining
    • ECM, EDM, USM and laser beam machining
    • Plasma arc machining
    • Electron beam machining

Unit contents are summarised from the official GUG syllabus . AiCanCode.org is not affiliated with Gondwana University, Gadchiroli.