GUG SY Civil syllabus

GUG · Second Year B.Tech. Civil Engineering · NEP 2020

Concrete Technology

STPCCCEC403 · Semester IV · 3 credits · IE 10 + mid-semester 10 + ESE 80

All notes for this subject
  1. Unit 1: Ingredients of Concrete

    9 hours

    Constituents, hydration and IS specifications of cement; sources, classification and characteristics of aggregates, their mechanical properties, bulking of sand, impact and abrasion tests, deleterious substances, soundness, crushed sand and alkali-aggregate reaction; quality of mixing water.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Cement: manufacture, types and hydration
    • Tests on cement: fineness, setting time and soundness
    • Aggregates and their properties
    • Aggregate tests: crushing, impact and abrasion values
    • Bulking of sand and crushed sand
    • Quality of water for concrete
  2. Unit 2: Properties of Fresh Concrete

    9 hours

    Shrinkage and creep and the factors affecting them, carbonation; IS 383, IS 456 and SP 23; batching, mixers and batching plants; workability by slump, compacting factor, flow table and Vee-Bee tests, setting time and the water-cement ratio; segregation, bleeding, voids and permeability; hot-weather concreting, conveying, placing, compaction and curing.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Creep and shrinkage of concrete
    • Batching, mixing, placing and curing
    • Workability and its tests
    • Concrete ingredients and the water–cement ratio
    • Segregation and bleeding
    • Hot-weather, cold-weather and mass concreting
  3. Unit 3: Strength and Testing of Hardened Concrete

    9 hours

    Gain of strength and the factors affecting compressive strength; tensile and flexural strength, failure modes, impact and fatigue strength, elasticity and Poisson's ratio; cube and cylinder tests and the aspect ratio, indirect tension, abrasion and accelerated curing tests; rebound hammer and ultrasonic pulse velocity tests.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Strength of hardened concrete
    • Cube, cylinder and split tensile strength tests
    • Maturity of concrete
    • Non-destructive testing of concrete
  4. Unit 4: Durability of Concrete and Admixtures

    9 hours

    Water as an agent of deterioration, permeability, sulphate, sea-water and acid attack, efflorescence, corrosion, abrasion and cavitation; pozzolanas, fly ash, silica fume, rice husk ash and GGBS; air-entraining, water-reducing, accelerating and retarding admixtures, plasticisers and superplasticisers.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Durability: sulphate attack and alkali–silica reaction
    • Permeability and the rapid chloride penetration test
    • Corrosion of reinforcement
    • Mineral admixtures: fly ash, silica fume and GGBS
    • Admixtures and fibres
  5. Unit 5: Concrete Mix Design

    9 hours

    IS 10262:2019 compared with the 1982 and 2009 editions; mix design of mass, ordinary and standard concrete, high-strength, self-compacting and pumpable concrete by IS methods; an overview of other methods.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Principles of mix design
    • IS 10262 mix design method
    • High-performance and self-compacting concrete

Unit contents are summarised from the official GUG syllabus . AiCanCode.org is not affiliated with Gondwana University, Gadchiroli.