Actuators
Actuators convert electrical signals into physical action in IoT devices; this note explains actuator types, DC motor electromechanics, control methods (PWM, H-bridge, drivers), protection, formulas and worked examples for engineering exams.
Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.
Why it matters
Actuators are the IoT components that convert an electrical command into physical change (motion, force, heat or fluid flow). Engineers use actuators when designing end nodes that must interact with the physical world: opening valves, moving parts, switching power, controlling temperature or pumping liquids.
Key ideas
For motion control the most important actuators:
- Brushed DC motor: rotary electromechanical device with brushes and commutator. Simple drive, controlled by voltage or PWM. Key variables: torque, speed, current.
- Brushless DC (BLDC) motor: uses electronic commutation (three-phase) for higher efficiency; needs a driver (ESC) that provides timed currents.
- Stepper motor: moves in discrete steps; position controlled open-loop by step pulses. Step angle = 360°/N where N is the number of full steps per revolution; microstepping divides this angle for smoother motion.
- Servo (hobby PWM servo): contains a small DC motor plus gearbox and internal controller; commanded by RC-style control pulses (typically 1–2 ms pulses repeated about every 20 ms) where position is encoded by pulse width, not by average-voltage PWM.
- Solenoid: linear actuator producing force when coil is energized (used for latching, valves).
- Relay / SSR: relays and SSRs can provide galvanic isolation between control and load; mechanical relays suit high-voltage/AC switching, while SSRs switch silently but have leakage/on-voltage. MOSFET switches do not provide isolation but offer silent, efficient DC switching.
Fundamental electromechanical relations for a simple DC motor (linear model, assumptions listed below):
- Electrical equation: the applied voltage equals resistive drop plus inductive drop plus generated back-EMF.
- Mechanical equation: produced torque equals motor constant times armature current; load torque resists rotation. In dynamics, J·(dω/dt) + b·ω + τ_load = τ, where J is rotor inertia and b is viscous friction.
- Under steady-state (dI/dt = 0), inductance can be ignored and algebraic relations follow.
Definitions used here:
- Back EMF (E): voltage induced in the motor proportional to angular velocity (opposes applied voltage): E = k_e · ω.
- Torque constant (k_t): proportionality between current and produced torque: τ = k_t · I.
- Stall torque: torque at zero speed (max torque) when motor current is maximum; in the simple model with supply V and armature resistance R, the stall current is I_stall = V/R (practically limited by the driver and heating).
- No-load speed: the angular speed when torque = 0 under a given supply voltage; approximately ω_0 ≈ V/k_e.
Control methods:
- PWM (pulse-width modulation): switch the supply rapidly between on and off; the average voltage seen by the actuator is V_avg = D·V_supply where D is duty cycle (0..1). Use PWM for efficient speed control of DC motors and power control of heaters.
- H-bridge: circuit of four switches (transistors or MOSFETs) to reverse the polarity across a DC motor for forward/reverse. Draw an H: left-top, left-bottom, right-top, right-bottom switches; motor in the center horizontal bar. To drive forward close left-top and right-bottom; reverse close right-top and left-bottom. Never close both tops or both bottoms (shoot-through); provide dead-time between switching events and ensure freewheel paths via MOSFET body diodes or external diodes across each switch.
- Drivers and interfaces: low-voltage microcontroller pins cannot drive motors directly. Use dedicated motor drivers (L293D, L298, DRV8833, TB6612) or MOSFETs/H-bridges. For BLDC use ESCs or 3-phase drivers. When using discrete MOSFETs, choose logic-level parts with Rds(on) specified at your gate-drive voltage (e.g., 3.3 V or 5 V) and ensure the gate driver can supply the required gate charge quickly.
Protection and reliability:
- Inductive loads produce back-EMF when switched. Always use flyback diodes for DC coils (place diode across coil, cathode at supply, anode at transistor drain/collector) and snubbers or TVS for fast transients.
- Gate protection and gate resistors for MOSFETs; heat-sinking for power devices; current limiting for motors.
- Choose switching frequency to be above audible range (>20 kHz) for motors to avoid noise; for heaters audible noise is not a concern, so a lower frequency may be used to reduce switching losses and EMI. In all cases, consider switching losses and driver limitations.
Assumptions behind the DC motor linear model used in derivations: magnetic linearity (no saturation), constant k_e and k_t, steady temperature (so R constant), small mechanical friction lumped in load torque, negligible armature inductance under steady-state analysis.
Drawings to prepare in exams (describe precisely):
- Draw an H-bridge: draw four transistors/MOSFETs forming an H, label the four switches Q1..Q4, label motor between midpoints, show supply V+ at top rail and GND at bottom. Indicate control signals for forward and reverse and show the four flyback paths: MOSFET body diodes or external diodes across each switch (do not place a single diode across the motor in an H-bridge).
- Draw a DC motor equivalent circuit: series elements R (armature resistance) and L (armature inductance) connected to supply V, with a dependent voltage source E = k_e·ω opposing V, and mechanical load torque τ_load opposing produced torque τ.
Formulas
V = R·I + L·(dI/dt) + E — V is applied voltage [V], R is armature resistance [Ω], I is current [A], L is armature inductance [H], dI/dt is time derivative of current [A/s], E is back EMF [V]. Applies to a DC motor electrical model.
E = k_e · ω — E back EMF [V], k_e motor back-EMF constant [V·s/rad], ω angular velocity [rad/s]. Applies in linear motor model.
τ = k_t · I — τ torque [N·m], k_t torque constant [N·m/A], I current [A]. Valid when motor constant is defined and linear region.
P_electrical = V · I — electrical input power [W].
P_mechanical = τ · ω — mechanical output power [W].
η = P_mechanical / P_electrical — efficiency (dimensionless, 0..1).
ω = (V - R·(τ/k_t)) / k_e — steady-state angular velocity [rad/s] derived eliminating I = τ/k_t and E = k_e ω from V equation when dI/dt = 0.
V_avg = D · V_supply — average voltage when using PWM, D duty cycle (0..1), V_supply supply voltage [V]. Applies when the PWM switching period T_sw is much shorter than the motor electrical time constant τ_e = L/R (equivalently, f_sw >> 1/τ_e), so current ripple is small.
θ_step = 360° / N — stepper motor full-step angle [degrees], N = number of steps per revolution.
P = V · I and P_loss_R = I^2 · R — power relations; used to calculate heating and Rds(on) losses.
(Units given in square brackets above; apply formulas only when model assumptions hold.)
Worked examples
- DC motor steady-state speed Given: supply V = 12.0 V, armature resistance R = 1.5 Ω, torque constant k_t = 0.08 N·m/A, back-EMF constant k_e = 0.08 V·s/rad (assume equal to k_t in SI), load torque τ_load = 0.48 N·m. Find steady-state angular speed ω and shaft power. Steps:
- Use I = τ / k_t = 0.48 / 0.08 = 6.0 A.
- Compute voltage drop R·I = 1.5 · 6.0 = 9.0 V.
- Back EMF E = V - R·I = 12.0 - 9.0 = 3.0 V.
- ω = E / k_e = 3.0 / 0.08 = 37.5 rad/s.
- Mechanical power P_mech = τ · ω = 0.48 · 37.5 = 18.0 W. Final answers: ω = 37.5 rad/s, P_mech = 18.0 W.
- PWM average voltage and approximate speed Given same motor as example 1 but driven from 12 V with PWM duty D = 0.6; assume PWM frequency is high so current ripple is small and V_avg ≈ D·V. Estimate no-load speed (ignore torque for no-load) and compare. Steps:
- V_avg = D · V_supply = 0.6 · 12.0 = 7.2 V.
- No-load current ≈ small; assume I ≈ 0 so E ≈ V_avg = 7.2 V.
- ω_no-load ≈ E / k_e = 7.2 / 0.08 = 90.0 rad/s. Final answer: V_avg = 7.2 V, ω_no-load ≈ 90.0 rad/s. (Under load, use steady-state relations with actual I.)
- Stepper motor step angle and pulses Given: a stepper with 200 full steps per revolution. Find step angle and pulses to rotate 90°. Steps:
- θ_step = 360° / 200 = 1.8° per step.
- Steps for 90° = 90 / 1.8 = 50 steps. Final answer: θ_step = 1.8°, 50 pulses for 90°.
Common mistakes
- Confusing k_e and k_t units or forgetting that equality k_e = k_t holds only when consistent SI units are used and no additional gear ratios are present.
- Neglecting Rds(on) losses for MOSFETs and contact resistance for relays when calculating heating.
- Closing both high-side (or both low-side) switches in an H-bridge (shoot-through) causing short-circuit.
- Using very low PWM frequency (< audible range) for motors causing audible noise, or too high frequency exceeding MOSFET switching capability.
- Treating PWM average voltage as exact when the PWM period is not much shorter than the motor electrical time constant τ_e = L/R (i.e., f_sw is not >> 1/τ_e).
For your exam
Question types you will see: definitions (actuator, back-EMF, torque constant), short notes (H-bridge, PWM, motor protection), derivations (derive steady-state speed equation for DC motor), numericals (compute speed, torque, power losses), circuit diagrams (draw and label H-bridge with protection), and design questions (select driver and protection for a given actuator).
What to include for full marks:
- State definitions clearly and in bold if required.
- List assumptions (e.g., steady-state, neglect L or linear magnetic behavior) before deriving formulas.
- Show step-by-step algebra with units carried through.
- Draw labelled diagrams for circuits; show direction of current and where protection components sit.
- For numerical answers, show intermediate steps (I, R·I, E, ω, power) and final values with correct SI units.
Quick check
- What is the relation between torque and current for a simple DC motor?
- How does PWM change the effective voltage supplied to a motor?
- Name two protection components needed when switching inductive actuators.
Answers: 1) τ = k_t · I. 2) V_avg = D · V_supply (D = duty cycle). 3) Flyback diode and snubber/TVS (also gate resistor for MOSFET).
Finished this topic? Mark it so your progress, study plan and readiness keep up.
Stuck on something here?