Physical layer: transmission media
Overview of physical transmission media: guided and unguided media, their properties, impairments (attenuation, dispersion, noise, crosstalk), important transmission-line formulas and typical numbers, with worked examples and exam guidance.
Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.
Why it matters
Transmission media are the physical paths that carry signals between network devices. Engineers choose media (twisted pair, coax, optical fibre, radio, microwave) and design link parameters (impedance matching, repeaters, modulation bandwidth) to meet required data rate, distance and reliability.
Key ideas
All terms are defined before use.
Transmission medium: the physical material or space that conveys electromagnetic signals from transmitter to receiver (examples: copper cable, optical fibre, free space).
Guided media: a medium that confines signal propagation to a physical path (examples: twisted pair, coaxial cable, optical fibre). Draw three separate diagrams: (1) twisted-pair: two insulated wires twisted, label conductor radius, insulation, twist; (2) coaxial cable: inner conductor, dielectric, outer conductor (shield), outer jacket, label inner radius a and outer radius b; (3) optical fibre cross-section: core radius, cladding, jacket and show ray paths for step-index. For coax with dielectric relative permittivity
ε_r,Z0 = (60/√ε_r)·ln(b/a). Typical characteristic impedances: UTP ≈ 100 Ω, RF coax ≈ 50 Ω, CATV coax ≈ 75 Ω.Unguided (wireless) media: signals propagate through open space—radio, microwave, infrared. For radio and microwave, draw a point transmitter and a spherical/front wave spreading; label free-space path loss.
Characteristic impedance (Z0): for a transmission line, Z0 is the ratio of voltage to current for a single forward-traveling wave. For the general lossy line with per-unit-length R (Ω/m), L (H/m), G (S/m), C (F/m), derive as follows (universities expect these steps): start from telegrapher's equations in frequency domain and solve for wave solutions; for a forward wave V(z)=V0+ e^{-γz} and I(z)=I0+ e^{-γz} the ratio V0+/I0+ = sqrt((R + jωL)/(G + jωC)). Thus define
- Propagation constant (γ) = sqrt((R + jωL)(G + jωC)) = α + jβ, where α is the attenuation constant (Np/m) and β is the phase constant (rad/m).
- For a lossless line (R = 0, G = 0):
Z0 = sqrt(L/C)andv = 1/sqrt(L·C)(phase velocity).
Reflection coefficient (Γ): when a load impedance ZL is not equal to Z0, part of the wave reflects. Define reflection coefficient at the load
Γ = (ZL - Z0)/(ZL + Z0)(unitless). Also define voltage standing wave ratio (VSWR):VSWR = (1 + |Γ|)/(1 - |Γ|).
Attenuation: exponential loss of amplitude/power along the medium. Express power loss in decibels (dB). Define decibel: for power ratio P2/P1,
dB = 10·log10(P2/P1). For amplitude (voltage) ratio V2/V1,dB = 20·log10(V2/V1)when impedances are equal. Also, conversion between nepers and decibels:1 Np = 8.686 dB.Skin effect: at high frequencies, current flows in a thin surface layer of a conductor; define skin depth (δ) as the depth where amplitude falls to 1/e: δ = sqrt(2/(ωμσ)). This increases resistance and attenuation with sqrt(frequency).
Crosstalk and electromagnetic interference (EMI): unwanted coupling from adjacent conductors or external sources. Define near-end crosstalk (NEXT) and far-end crosstalk (FEXT); shielding and twisting reduce crosstalk.
Optical-fibre specifics:
- Modal dispersion: in multimode fibres different modes travel different path lengths → pulse broadening.
- Chromatic dispersion: different wavelengths travel at different speeds in the material → pulse broadening proportional to spectral width of source and distance; units typically ps/(nm·km).
- Attenuation commonly given in dB/km; typical low-loss single-mode fibre has minimum around 1550 nm.
- Numerical aperture (NA): for step-index fibre,
NA = sqrt(n_core^2 - n_cladding^2), which determines acceptance angle. In air (n0 ≈ 1), the acceptance half-angleθ_maxsatisfiessin θ_max = NA.
Free-space propagation loss (Friis simplified form for line-of-sight): received power decreases with square of distance and depends on antenna gains and wavelength. Define free-space path loss (FSPL) in dB as
FSPL(dB) = 20·log10(4πd/λ)where d is distance and λ wavelength. Also, Friis transmission equation:Pr = Pt·Gt·Gr·(λ/(4πd))^2(assuming matched polarizations and no additional losses).
Notes on assumptions: lossless approximations assume R, G ≈ 0; many cable formulas assume homogeneous TEM mode. For fibres, step-index vs graded-index models differ; use graded-index to reduce modal dispersion.
Formulas
Z0 = sqrt((R + j·ω·L)/(G + j·ω·C)) — Z0 is characteristic impedance (Ω), R per-unit-length (Ω/m), L (H/m), G (S/m), C (F/m); general lossy line, frequency ω rad/s.
Z0 = sqrt(L/C) — for a lossless line (R = 0, G = 0); Z0 in Ω, L in H/m, C in F/m.
γ = sqrt((R + j·ω·L)·(G + j·ω·C)) = α + j·β — propagation constant: α attenuation (Np/m), β phase constant (rad/m).
v = ω/β = 1/sqrt(L·C) — phase velocity (m/s) for lossless line. For a uniform dielectric (TEM), v = c/√ε_r and the velocity factor is v/c = 1/√ε_r.
λ = v/f — wavelength in medium (m), f frequency (Hz).
Γ = (ZL - Z0)/(ZL + Z0) — reflection coefficient (unitless). ZL, Z0 in Ω. Along the line at distance z from the load: Γ(z) = Γ_L·e^{-2γz}.
VSWR = (1 + |Γ|)/(1 - |Γ|) — voltage standing wave ratio (unitless). Return loss: RL = -20·log10(|Γ|) (dB).
dB (power) = 10·log10(P2/P1) — decibels for power ratios; P in watts (W).
dB (voltage) = 20·log10(V2/V1) — decibels for voltage amplitude ratios when impedances equal; V in volts (V).
FSPL(dB) = 20·log10(4·π·d/λ) — free-space path loss in dB; d in metres, λ in metres.
δ = sqrt(2/(ω·μ·σ)) — skin depth (m); ω rad/s, μ permeability (H/m), σ conductivity (S/m).
NA = sqrt(n_core^2 - n_cladding^2) — numerical aperture (unitless); n are refractive indices.
Worked examples
- Power attenuation in dB and per km
- Problem: A 1 km length of coax causes an input power 100 mW to fall to 63.1 mW at the output. Find attenuation in dB and dB/km.
- Steps:
- Use power dB formula:
dB = 10·log10(Pout/Pin). - Substitute:
dB = 10·log10(63.1/100) = 10·log10(0.631). - Compute log10(0.631) ≈ -0.200, so dB ≈ -2.00 dB (negative means loss).
- Per km attenuation = -2.00 dB / 1 km = 2.00 dB/km.
- Use power dB formula:
- Final answer: 2.00 dB total attenuation, 2.00 dB/km.
- Reflection coefficient and VSWR on a cable
- Problem: A line has Z0 = 50 Ω and is terminated with ZL = 75 Ω. Compute Γ and VSWR.
- Steps:
Γ = (ZL - Z0)/(ZL + Z0) = (75 - 50)/(75 + 50) = 25/125 = 0.2.VSWR = (1 + |Γ|)/(1 - |Γ|) = (1 + 0.2)/(1 - 0.2) = 1.2/0.8 = 1.5.
- Final answer: Γ = 0.2, VSWR = 1.5.
- Wavelength in an optical fibre
- Problem: Light of free-space wavelength 1550 nm travels in a fibre core with refractive index n = 1.468. Find wavelength in the core and phase velocity.
- Steps:
- Speed of light c = 3.00·10^8 m/s. Phase velocity v = c/n = 3.00·10^8 / 1.468 ≈ 2.043·10^8 m/s.
- Free-space wavelength λ0 = 1550 nm = 1.55·10^-6 m. Wavelength in core λ = λ0 / n = 1.55·10^-6 / 1.468 ≈ 1.056·10^-6 m = 1056 nm.
- Final answer: Wavelength in core ≈ 1056 nm, phase velocity ≈ 2.043·10^8 m/s.
Common mistakes
- Confusing characteristic impedance Z0 with DC resistance; Z0 depends on L and C, not just conductor resistivity at low freq.
- For optical fibres, saying "modal dispersion" for single-mode fibres; single-mode does not have modal dispersion (it has chromatic dispersion and polarization mode dispersion).
- Using free-space wavelength λ0 where medium wavelength λ = λ0/n should be used.
For your exam
Kinds of questions and what full-marks answers include:
- Definitions and short notes: define guided vs unguided, skin effect, modal vs chromatic dispersion, characteristic impedance. Full marks need crisp definitions and at least one practical effect or mitigation method.
- Derivations: derive characteristic impedance and propagation constant from telegrapher's equations; include assumptions and final formula. Draw a small diagram of a differential segment with R, L, G, C labeled.
- Numericals: dB conversions, reflection coefficient, VSWR, FSPL, wavelength in medium. Show all steps, include units, and final value labelled clearly.
- Diagrams: draw cross-sections (twisted pair, coax, optical fibre) and ray sketches for single-mode vs multimode; label important dimensions and parameters.
- Design/qualitative: explain why twisted pair is used for LAN, why optical fibre preferred for long-haul, effects of shielding and why impedance matching matters. Full marks require reasons, not just features.
Quick check
- What is the formula for the reflection coefficient at a load?
- How many dB is a power ratio of 10:1?
- Does multimode fibre have modal dispersion or chromatic dispersion?
Answers: Γ = (ZL - Z0)/(ZL + Z0); 10 dB; multimode fibre has modal dispersion (it may also have chromatic dispersion).
Finished this topic? Mark it so your progress, study plan and readiness keep up.
Stuck on something here?