SPPU TE E&TC syllabus

SPPU · Third Year Electronics & Telecommunication Engineering · 2024 Pattern

VLSI Design

PCC-303-ETC · Semester V · 3 credits · CCE 30 + end-semester 70

  1. Unit 1: Verilog HDL and Hierarchical Modelling

    9 hours

    Verilog design flow, top-down and bottom-up methodology, module structure and port declarations; design hierarchy, module instantiation; behavioural, dataflow, gate and switch levels of abstraction; compiler directives, system tasks and functions; simulation versus synthesis and test benches.

    Marks: 14 in the end-semester exam · CCE: Unit test (12 marks, Units 1 & 2)

    • Verilog design flow and methodology
    • Verilog modules, ports and instantiation
    • Levels of abstraction in Verilog
    • Compiler directives and system tasks
    • Simulation, synthesis and test benches
    • Hierarchical modelling examples
  2. Unit 2: Verilog Fundamentals and Combinational Modelling

    9 hours

    Nets and variables, scalars and vectors, number representation; operators including concatenation, replication and the conditional operator; parameters; gate-level modelling and gate delays; dataflow modelling with continuous assignment; multiplexers, decoders, encoders and adders with test benches.

    Marks: 14 in the end-semester exam · CCE: Unit test (12 marks, Units 1 & 2)

    • Verilog data types and number representation
    • Verilog operators
    • Gate-level modelling and delays
    • Dataflow modelling and continuous assignment
    • Combinational circuits in Verilog
  3. Unit 3: Behavioural Modelling and Sequential Circuits

    9 hours

    initial and always blocks, event control and sensitivity lists; blocking versus non-blocking assignment; if–else and case; edge-triggered modelling with synchronous and asynchronous reset; flip-flops, registers, counters and shift registers with test benches; propagation delay, setup and hold time.

    Marks: 14 in the end-semester exam · CCE: Assignments or case study (12 marks, Units 3 & 4)

    • Behavioural modelling: initial and always blocks
    • Blocking and non-blocking assignments
    • if–else and case statements
    • Flip-flops with synchronous and asynchronous reset
    • Counters and shift registers in Verilog
    • Setup time, hold time and propagation delay
  4. Unit 4: Finite State Machines in Verilog

    9 hours

    FSM design methodology; Moore and Mealy machines, state diagrams and tables, next-state and output logic, coding styles; overlapping and non-overlapping sequence detectors; traffic-light, vending-machine and lift controllers.

    Marks: 14 in the end-semester exam · CCE: Assignments or case study (12 marks, Units 3 & 4)

    • FSM design methodology
    • Moore and Mealy FSMs in Verilog
    • FSM coding styles
    • Sequence detectors in Verilog
    • Controller design: traffic light and vending machine
  5. Unit 5: FPGA Architecture and Design Flow

    9 hours

    PLDs, CPLD and FPGA architecture: CLBs, LUTs, IOBs and routing; the FPGA design flow from entry to bitstream, constraints and pin assignment; programming techniques; CPLD versus FPGA; JTAG and boundary scan.

    Marks: 14 in the end-semester exam · CCE: Seminar, open-book test or quiz (6 marks, Unit 5)

    • CPLD and FPGA architecture
    • CLBs, LUTs, IOBs and interconnect
    • FPGA design flow
    • JTAG and boundary scan

Unit contents are summarised from the official SPPU syllabus . AiCanCode.org is not affiliated with Savitribai Phule Pune University.