SPPU TE E&TC syllabus

SPPU · Third Year Electronics & Telecommunication Engineering · 2024 Pattern

Microcontrollers and Applications

PCC-301-ETC · Semester V · 3 credits · CCE 30 + end-semester 70

  1. Unit 1: Introduction to Microcontrollers

    9 hours

    Microprocessors versus microcontrollers; Von Neumann and Harvard architectures, CISC and RISC, pipelining; 8- to 64-bit microcontrollers and selection criteria; the 8051's features, block diagram, registers, memory organisation, interrupts and serial communication.

    Marks: 14 in the end-semester exam · CCE: Unit test (12 marks, Units 1 & 2)

    • Microprocessors versus microcontrollers
    • Von Neumann and Harvard, CISC and RISC architectures
    • Selecting a microcontroller
    • 8051 architecture and register set
    • 8051 memory organisation
    • 8051 interrupts and serial communication
  2. Unit 2: Programming the 8051

    8 hours

    8051 pin-out and port structure; timers and counters, delay calculation and programming; port programming; interfacing LEDs, LCD, LDR, seven-segment displays, relays and buzzers in Embedded C; a data acquisition system.

    Marks: 14 in the end-semester exam · CCE: Unit test (12 marks, Units 1 & 2)

    • 8051 pin diagram and port structure
    • 8051 timers, counters and delay generation
    • Interfacing LEDs, relays and buzzers with the 8051
    • Interfacing LCD and seven-segment displays with the 8051
    • Data acquisition system with the 8051
  3. Unit 3: ARM7 Fundamentals and Architecture

    8 hours

    ARM processors and versions, the ARM core data-flow model and programmer's model, operating modes, registers, CPSR and SPSR; ARM7 versus ARM9 and ARM11; the LPC2148: features, block diagram, memory map, GPIO and the pin connect block.

    Marks: 14 in the end-semester exam · CCE: Assignments or case study (12 marks, Units 3 & 4)

    • ARM core data flow and programmer's model
    • ARM operating modes, registers, CPSR and SPSR
    • ARM7, ARM9 and ARM11 compared
    • LPC2148 features and architecture
    • LPC2148 memory map, GPIO and pin connect block
  4. Unit 4: ARM7 Microcontroller Interfaces

    9 hours

    The LPC2148 system control block: PLL configuration, power control and the VPB divider; 32-bit timers with match registers and prescalers; the interrupt structure; GPIO programming with LEDs, GLCD and keypads; timer delays.

    Marks: 14 in the end-semester exam · CCE: Assignments or case study (12 marks, Units 3 & 4)

    • LPC2148 PLL, power control and VPB divider
    • LPC2148 timers and match registers
    • LPC2148 interrupt structure
    • LPC2148 GPIO programming: LED, keypad and GLCD
  5. Unit 5: Real-world Interfacing with ARM

    9 hours

    UART programming for transmitting to and receiving from a computer; the 10-bit ADC and the DAC; GSM and GPS modules; EEPROM over I2C and SD cards over SPI.

    Marks: 14 in the end-semester exam · CCE: Seminar, open-book test or quiz (6 marks, Unit 5)

    • UART programming on the LPC2148
    • ADC and DAC on the LPC2148
    • GSM and GPS module interfacing
    • I2C EEPROM and SPI SD card interfacing

Unit contents are summarised from the official SPPU syllabus . AiCanCode.org is not affiliated with Savitribai Phule Pune University.