SPPU · Third Year Electronics & Telecommunication Engineering · 2024 Pattern
CMOS Process Technology
PEC-361D-ETC · Elective II · Semester VI · 3 credits · CCE 30 + end-semester 70
One of the Elective II options.
Unit 1: MOS Technology and CMOS Fundamentals
9 hoursIC evolution and Moore's law; NMOS and PMOS operation, long-channel I–V characteristics and the capacitance model; mobility degradation, velocity saturation, channel-length modulation and body effect; the CMOS inverter, its VTC, noise margins and delay; static and dynamic power; SPICE models and DC and transient analysis.
Marks: 14 in the end-semester exam · CCE: Unit test (12 marks, Units 1 & 2)
- IC evolution and Moore's law
- MOSFET operation and long-channel I–V characteristics
- MOS capacitances and non-ideal effects
- CMOS inverter: VTC and noise margins
- CMOS delay and power dissipation
- SPICE modelling of MOSFETs
Unit 2: CMOS Logic and Layout Design
9 hoursCMOS NAND and NOR gates and transmission gates; combinational design with CMOS and TGs; W/L sizing; stick diagrams and lambda design rules; layout layers and masks; inverter, NAND and NOR layouts; DRC and LVS.
Marks: 14 in the end-semester exam · CCE: Unit test (12 marks, Units 1 & 2)
- CMOS NAND and NOR gates
- Transmission gates and CMOS combinational design
- Transistor sizing: W/L ratio
- Stick diagrams and lambda design rules
- Layout of CMOS gates, DRC and LVS
Unit 3: CMOS Fabrication I: Wafer Preparation
9 hoursMetallurgical and electronic-grade silicon; Czochralski and float-zone growth and wafer formation; dry and wet thermal oxidation; doping; vapour-phase and molecular-beam epitaxy; photolithography and photoresists; cleanrooms, contamination control and inspection.
Marks: 14 in the end-semester exam · CCE: Assignments or case study (12 marks, Units 3 & 4)
- Silicon refining and crystal growth
- Thermal oxidation
- Epitaxy: VPE and MBE
- Photolithography
- Cleanrooms and contamination control
Unit 4: CMOS Fabrication II: Doping, Etching, Deposition and Metallization
9 hoursDiffusion and ion implantation; wet, dry and reactive-ion etching; PVD and CVD; polysilicon and dielectric deposition; metallization and CMP; LOCOS and STI isolation; the n-well CMOS flow; latch-up and its prevention; integration and yield.
Marks: 14 in the end-semester exam · CCE: Assignments or case study (12 marks, Units 3 & 4)
- Diffusion and ion implantation
- Etching: wet, dry and RIE
- Thin-film deposition: PVD and CVD
- Metallization and CMP
- LOCOS and STI isolation
- N-well CMOS process flow and latch-up
Unit 5: Advanced CMOS Technologies
9 hoursMOSFET scaling and short-channel effects (oxide breakdown, DIBL, GIDL, gate tunnelling, NBTI); high-k metal gates; FinFET, SOI and GAA; 3D ICs, TSVs and advanced packaging; SEM, TEM and SIMS characterisation.
Marks: 14 in the end-semester exam · CCE: Seminar, open-book test or quiz (6 marks, Unit 5)
- MOSFET scaling and short-channel effects
- High-k dielectrics and metal gates
- FinFET, SOI and GAA devices
- 3D ICs, TSVs and advanced packaging
- Semiconductor characterisation: SEM, TEM and SIMS
Unit contents are summarised from the official SPPU syllabus . AiCanCode.org is not affiliated with Savitribai Phule Pune University.