SPPU SE E&TC syllabus

SPPU · Second Year Electronics & Telecommunication Engineering · 2024 Pattern

Electronics Circuits

PCC-201-ETC · Semester III · 3 credits · CCE 40 + end-semester 60

  1. Unit 1: MOSFET & its Analysis

    8 hours

    Enhancement MOSFET biasing and the voltage-divider bias, DC load line, AC equivalent circuit and parameters; non-ideal behaviour: finite output resistance, body effect, sub-threshold conduction, breakdown, temperature and W/L effects; the common-source amplifier, its AC analysis and frequency response; the source follower; BJT versus MOSFET.

    Marks: 12 in the end-semester exam · CCE: Unit test (15 marks, Units 1 & 2)

    • Enhancement MOSFET: structure and characteristics
    • MOSFET biasing and the DC load line
    • MOSFET small-signal equivalent circuit and parameters
    • Non-ideal MOSFET effects
    • Common-source amplifier and its AC analysis
    • Frequency response of the CS amplifier
    • Source follower
    • BJT versus MOSFET
  2. Unit 2: MOSFET Circuits

    8 hours

    MOSFET as a switch, CMOS inverter, MOSFET resistor and diode; current sink, source and mirror; feedback types, the four topologies and their effects, voltage-series and current-series feedback amplifiers; the Barkhausen criterion, RC phase-shift and crystal oscillators.

    Marks: 12 in the end-semester exam · CCE: Unit test (15 marks, Units 1 & 2)

    • MOSFET as a switch and the CMOS inverter
    • MOSFET as resistor and diode
    • Current sources, sinks and current mirrors
    • Feedback topologies and their effects
    • Voltage-series and current-series feedback amplifiers
    • Barkhausen criterion and types of oscillators
    • RC phase-shift oscillator
    • Crystal oscillator
  3. Unit 3: Operational Amplifier and Linear Applications

    9 hours

    Op-amp block diagram, parameters and AC/DC characteristics; inverting and non-inverting amplifiers and the effect of feedback on input and output resistance, gain and bandwidth; voltage follower, summing and differential amplifiers, practical integrator and differentiator, precision half- and full-wave rectifiers.

    Marks: 12 in the end-semester exam · CCE: Assignments or case study (15 marks, Units 3 & 4)

    • Op-amp block diagram and ideal characteristics
    • Op-amp parameters: DC and AC
    • Inverting and non-inverting amplifiers
    • Voltage follower, summing and differential amplifiers
    • Practical integrator and differentiator
    • Precision half-wave and full-wave rectifiers
  4. Unit 4: Op-amp and Non-linear Applications

    9 hours

    Comparator, Schmitt trigger, square and triangular wave generators and the PWM generator; weighted-resistor and R-2R DACs; SAR, flash and dual-slope ADCs with their characteristics, specifications and comparison.

    Marks: 12 in the end-semester exam · CCE: Assignments or case study (15 marks, Units 3 & 4)

    • Comparators and the Schmitt trigger
    • Square and triangular wave generators
    • PWM generator
    • Weighted-resistor and R-2R ladder DACs
    • SAR, flash and dual-slope ADCs
    • ADC and DAC specifications and comparison
  5. Unit 5: Voltage Regulators

    9 hours

    Power-supply block diagram, fixed and variable three-terminal regulators, the linear regulator, IC 317 and IC 337 with typical circuits and current boosting, low-dropout regulators; SMPS types and specifications, buck and boost converters; linear versus switch-mode supplies.

    Marks: 12 in the end-semester exam · CCE: Seminar, open-book test or quiz (10 marks, Unit 5)

    • Power supply block diagram and three-terminal regulators
    • Adjustable regulators: IC 317 and IC 337
    • Current boosting and low-dropout regulators
    • SMPS: buck and boost converters
    • Linear versus switch-mode power supplies

Unit contents are summarised from the official SPPU syllabus . AiCanCode.org is not affiliated with Savitribai Phule Pune University.