PAHSU TY Electrical syllabus

PAHSU · Third Year B.Tech. Electrical Engineering · NEP 2020

Power Electronics & Industrial Drives

EEPCC-11 · Semester VI · 4 credits · ISE 30 + ESE 70

  1. Unit 1: Silicon Controlled Rectifier and Semiconductor Devices

    7 hours

    Principle, static and dynamic characteristics and turn-on methods of the SCR; R and RC firing circuits; class C and D commutation; over-voltage, over-current, dv/dt and di/dt protection; principle, V-I characteristics, ratings and applications of the TRIAC, DIAC and GTO.

    Examined in the 70-mark end-semester paper

    • SCR characteristics and ratings
    • SCR triggering circuits
    • Commutation techniques
    • SCR protection
    • TRIAC
    • GTO and MCT
  2. Unit 2: Phase Controlled Rectifiers and Choppers

    7 hours

    Half-wave and full-wave (half- and fully controlled) rectifiers with R and RL loads, with and without freewheeling diode; three-phase half- and fully controlled rectifiers with R load; chopper principle, classification and control; step-down and step-up choppers; buck, boost, buck-boost and Cuk regulators.

    Examined in the 70-mark end-semester paper

    • Single-phase half-controlled converter
    • Single-phase fully controlled converter
    • Freewheeling diode
    • Three-phase half-controlled converter
    • Three-phase fully controlled converter
    • Chopper principle and control techniques
    • Buck converter
    • Boost converter
    • Buck-boost converter
  3. Unit 3: Inverters and AC Voltage Controllers

    7 hours

    Classification and principle of inverters; single-phase half- and full-bridge inverters with R and RL loads; three-phase bridge inverters in 120 and 180 degree modes; voltage control of single-phase inverters; on-off and phase control; single-phase bidirectional AC voltage control with R load.

    Examined in the 70-mark end-semester paper

    • Single-phase full-bridge inverter
    • Three-phase inverter: 120 and 180 degree modes
    • Voltage control of single and three-phase inverters
    • Integral cycle control
    • Single-phase AC voltage controller
  4. Unit 4: Introduction and Dynamics of Electrical Drives

    7 hours

    Block diagram, types and parts of electrical drives; selecting a drive; the fundamental torque equation, speed-torque conventions and multi-quadrant operation; closed-loop control of drives.

    Examined in the 70-mark end-semester paper

    • Electric drive components
    • Selection of drive components
    • Dynamics of electric drives and torque equations
    • Four-quadrant operation
    • Closed-loop control, current limit and speed sensing
  5. Unit 5: DC Drives

    7 hours

    Single-phase and three-phase half- and fully controlled converter-fed DC motor drives; single- and multi-quadrant chopper-controlled DC shunt motor drives; electrical braking; BLDC motor drives and converter circuits.

    Examined in the 70-mark end-semester paper

    • Converter-fed DC drives
    • Chopper-fed DC motor drives
    • Braking of DC drives
    • BLDC drive operation
  6. Unit 6: AC Drives

    7 hours

    Stator voltage control of induction motors by AC regulators; variable-frequency control by VSI and CSI and their comparison; VSI-fed and multiple synchronous motor drives; stepper and switched reluctance motor drives and their converters.

    Examined in the 70-mark end-semester paper

    • Stator voltage and V/f control
    • VSI and CSI fed induction motor drives
    • Synchronous motor variable-speed drives
    • Control of reluctance motor drives

Unit contents are summarised from the official PAHSU syllabus . AiCanCode.org is not affiliated with Punyashlok Ahilyadevi Holkar Solapur University (PAHSU).