Mumbai University BE EXTC syllabus

Mumbai University · Final Year Electronics and Telecommunication Engineering · Rev-2019 'C' Scheme

Microwave Engineering

ECC701 · Semester VII · 3 credits · Internal tests 20 (average of two) + end-semester 80

End-semester paper (3 hours): Six questions of 20 marks; Q1 is compulsory and you answer four. Each module's share of the paper follows its lecture hours.

  1. Module 1: Transmission Lines

    6 hours

    Transmission line equations; open and short-circuited lines; impedance along a line; the Smith chart and impedance matching; microstrip, strip and coplanar lines.

    Examined in the 80-mark end-semester paper (about 15% of it, by lecture hours); the class tests cover what has been taught by then

    • Transmission line equations
    • Open and short-circuited lines
    • Smith chart and impedance matching
    • Striplines
    • Microstrip and coplanar lines
  2. Module 2: Waveguides

    7 hours

    Microwave bands and applications; rectangular waveguides; TE and TM fields and modes; why TEM cannot exist; cut-off; wave impedance; dominant and degenerate modes; phase and group velocity; rectangular cavity resonators.

    Examined in the 80-mark end-semester paper (about 18% of it, by lecture hours); the class tests cover what has been taught by then

    • Microwave frequency bands and applications
    • Rectangular waveguides and modes
    • TE and TM field components
    • Cut-off frequency and dominant mode
    • Phase and group velocity in waveguides
    • Cavity resonators
  3. Module 3: Waveguide Components

    6 hours

    Probe, loop and cavity coupling; irises, tuning screws and matched loads; attenuators and phase shifters; E-plane, H-plane and magic tees; hybrid ring; ferrites, gyrators, isolators and circulators.

    Examined in the 80-mark end-semester paper (about 15% of it, by lecture hours); the class tests cover what has been taught by then

    • Waveguide excitation and coupling
    • Waveguide attenuators and phase shifters
    • E-plane, H-plane and magic tees
    • Hybrid ring
    • Ferrites and Faraday rotation
    • Isolators and circulators
  4. Module 4: Microwave Tubes

    10 hours

    Limits of conventional tubes; velocity modulation and bunching; two-cavity and reflex klystrons; helix TWT and slow-wave structures; crossed-field tubes; cylindrical magnetron, Hull cut-off and Hartree conditions, π-mode.

    Examined in the 80-mark end-semester paper (about 26% of it, by lecture hours); the class tests cover what has been taught by then

    • Limitations of conventional tubes at microwaves
    • Velocity modulation and klystrons
    • Reflex klystron
    • Helix travelling wave tube
    • Cavity magnetron
    • Hull cut-off and Hartree conditions
  5. Module 5: Microwave Semiconductor Devices

    6 hours

    Tunnel, PIN and varactor diodes; crystal detectors; Gunn diodes and RWH theory; IMPATT, TRAPATT and BARITT diodes.

    Examined in the 80-mark end-semester paper (about 15% of it, by lecture hours); the class tests cover what has been taught by then

    • PIN, tunnel and Schottky diodes
    • Gunn diode
    • IMPATT and TRAPATT diodes
    • BARITT diode
  6. Module 6: Microwave Measurements

    4 hours

    The microwave bench; bolometer power measurement; attenuation; low and high VSWR; cavity Q; impedance.

    Examined in the 80-mark end-semester paper (about 10% of it, by lecture hours); the class tests cover what has been taught by then

    • Microwave bench
    • Microwave measurements: VSWR, power and impedance
    • Measurement of cavity Q

Module contents are summarised from the official Mumbai University syllabus . AiCanCode.org is not affiliated with the University of Mumbai.