GUG SY E&TC syllabus

GUG · Second Year B.Tech. Electronics and Telecommunication Engineering · NEP 2020

Linear Integrated Circuits

STPCCETC305 · Semester III · 3 credits · IE 10 + mid-semester 10 + ESE 80

Unit 1 also covers the classification of ICs and IC packages.

  1. Unit 1: Introduction to Integrated Circuits and Operational Amplifiers

    8 hours

    Analog, digital and mixed ICs and IC packages; the op-amp's internal stages; the ideal op-amp in inverting and non-inverting, open- and closed-loop configurations; CMRR, input and output impedance, slew rate, offset voltage and bias currents; frequency response, drift and compensation of practical op-amps.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Op-amp block diagram and ideal characteristics
    • Op-amp parameters: DC and AC
    • Frequency response of op-amp circuits and Bode plots
    • Op-amp frequency compensation
  2. Unit 2: Linear Applications of Op-Amps

    8 hours

    Inverting and non-inverting amplifiers and the voltage follower; difference, instrumentation and summing amplifiers; the integrator and differentiator and their practical limitations.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Inverting and non-inverting amplifiers
    • Voltage follower, summing and differential amplifiers
    • Instrumentation amplifier
    • Practical integrator and differentiator
  3. Unit 3: Non-linear Applications of Op-Amps

    8 hours

    Comparators and zero-crossing detectors; the Schmitt trigger and hysteresis; waveform generators, peak detector, clipper and clamper; half-wave and full-wave precision rectifiers; the phase-locked loop and its applications.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Comparators and the Schmitt trigger
    • Zero-crossing and window detectors
    • Square and triangular wave generators
    • Peak detectors and analog multipliers
    • Clippers and clampers using op-amps
    • Precision half-wave and full-wave rectifiers
    • Phase-locked loop and its applications
  4. Unit 4: Active Filters and Oscillators

    8 hours

    Low-pass, high-pass, band-pass and band-stop active filters: design and frequency response; second-order Butterworth, Chebyshev and Bessel filters; the Barkhausen criterion and the op-amp Wien bridge and phase-shift oscillators.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • First and second-order active filters
    • Butterworth, Chebyshev and Bessel active filter responses
    • Notch and all-pass filters
    • Barkhausen criterion and types of oscillators
    • Wien bridge oscillator
    • RC phase-shift oscillator
  5. Unit 5: Voltage Regulators, Timers and Special ICs

    8 hours

    Fixed and adjustable linear regulators (78xx, LM317); the 555 timer as astable and monostable multivibrator; PLL ICs and voltage-controlled oscillators; analog-to-digital and digital-to-analog converters.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Power supply block diagram and three-terminal regulators
    • Adjustable regulators: IC 317 and IC 337
    • IC 555 timer
    • Astable and monostable multivibrators
    • Voltage-controlled oscillators
    • Weighted-resistor and R-2R ladder DACs
    • SAR, flash and dual-slope ADCs

Unit contents are summarised from the official GUG syllabus . AiCanCode.org is not affiliated with Gondwana University, Gadchiroli.