GUG SY Electrical syllabus

GUG · Second Year B.Tech. Electrical Engineering · NEP 2020

Electrical Machine-I

STPCCELE403 · Semester IV · 3 credits · IE 10 + mid-semester 10 + ESE 80

Unit III in the PDF opens with a paragraph repeated from Network Analysis (phasors, three-phase and coupled circuits); the unit's own content is the DC motor.

  1. Unit 1: Magnetic Fields and Magnetic Circuits

    8 hours

    MMF, flux, reluctance and inductance; Ampere's and Biot-Savart laws; magnetic fields in air and iron; B-H curves, flux linkage and linear and nonlinear magnetic circuits; hysteresis and eddy-current losses; Faraday's law; force on a current-carrying conductor.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Magnetic circuits and reluctance
    • Magnetic materials and magnetisation
    • Separation of hysteresis and eddy-current losses
    • Faraday's law
    • Magnetic forces
  2. Unit 2: DC Generator

    8 hours

    Parts of the generator; armature windings, pitches, single- and two-layer, multiplex, lap and wave windings, dummy coils and equalisers; types of generators; EMF and torque equations, losses and efficiency; armature reaction, compensating windings, commutation and interpoles; characteristics, critical speed and parallel operation.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Construction and EMF equation of DC generators
    • Lap and wave armature windings
    • Types of DC machines by excitation
    • Armature reaction and commutation
    • Open-circuit characteristic of a DC generator
    • Losses and efficiency of DC machines
    • Parallel operation of DC generators
  3. Unit 3: DC Motor

    8 hours

    Motor principle and generator versus motor action; back EMF, power and torque, shaft torque; characteristics, losses, efficiency and power stages; speed control and electric braking; the need for a starter, three- and four-point starters.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Back EMF and torque equation of DC motors
    • Characteristics of DC shunt and series motors
    • Speed control of DC motors
    • Braking of DC motors
    • DC motor starters
  4. Unit 4: Single-Phase Transformer

    8 hours

    Construction, principle and types; no-load and on-load operation, phasor diagrams and the equivalent circuit; losses, efficiency and regulation by direct and indirect tests, Sumpner's test; parallel operation; the autotransformer; maximum and all-day efficiency.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Ideal transformer
    • Phasor diagrams of a transformer
    • Equivalent circuit of a transformer
    • Voltage regulation of a transformer
    • Efficiency and all-day efficiency
    • Open-circuit and short-circuit tests on transformers
    • Sumpner's test
    • Parallel operation and load sharing
    • Autotransformers
  5. Unit 5: Three-Phase Transformers

    8 hours

    Star and delta connections and the zigzag; terminal marking, vector diagrams and phase groups; parallel operation; Scott and V-V connections; tertiary windings; testing; transients; off-load and on-load tap changers; harmonics.

    Examined in the 80-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Three-phase transformer connections
    • Vector groups
    • Scott and V-V connections
    • Three-winding transformers
    • On-load tap changers
    • Harmonics and the oscillating neutral

Unit contents are summarised from the official GUG syllabus . AiCanCode.org is not affiliated with Gondwana University, Gadchiroli.