DBATU SY E&TC syllabus

DBATU · Second Year B.Tech Electronics & Telecommunication Engineering · NEP 2020

Digital Electronics

25AF1372PC303 · Semester III · 3 credits · Continuous assessment 20 + mid-semester 20 + end-semester 60

  1. Unit 1: Combinational Logic Design

    SOP and POS forms and K-map minimisation up to four variables with don't-cares; arithmetic circuits, BCD-to-seven-segment decoder and code converters; adders as subtractors, look-ahead carry, ALU, comparators, parity generators, multiplexers, demultiplexers and decoders.

    Examined in the 60-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • SOP and POS forms of logic functions
    • K-map minimisation with don't-care conditions
    • Adders, subtractors and the look-ahead carry generator
    • Code converters
    • Magnitude comparator
    • Parity generators and checkers
    • Multiplexers and multiplexer trees
    • Demultiplexers and decoders
  2. Unit 2: Sequential Logic Design

    1-bit memory cell; clocked SR, JK, master–slave JK, D and T flip-flops, preset and clear; excitation tables and conversion; registers, shift registers, ring and twisted-ring counters, sequence generators, ripple, up/down and synchronous counters; lock-out, clock skew and jitter.

    Examined in the 60-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Latches and the SR flip-flop
    • JK, master–slave JK, D and T flip-flops
    • Excitation tables and flip-flop conversion
    • Registers and shift registers
    • Ripple and mod-n counters
    • Synchronous and up/down counters
    • Ring and twisted-ring counters, sequence generators
    • Lock-out, clock skew and clock jitter
  3. Unit 3: State Machines

    State diagram, state table, state reduction and state assignment; Mealy and Moore machines; FSM implementation; sequence detectors.

    Examined in the 60-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Moore and Mealy machines
    • State diagrams, state tables and state reduction
    • State assignment and FSM implementation
    • Sequence detector design
  4. Unit 4: Digital Logic Families

    Characteristics of digital ICs; TTL NAND gate, active pull-up, wired AND, open collector and tri-state logic; CMOS inverter, NAND and NOR gates and open drain; CMOS–TTL interfacing; TTL, CMOS, ECL, RTL, I2L and DCTL compared.

    Examined in the 60-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • Characteristics of digital ICs
    • TTL NAND gate
    • Open-collector and tri-state outputs
    • CMOS gates and CMOS versus TTL
    • Interfacing CMOS and TTL
  5. Unit 5: Programmable Logic, Memories and VHDL

    PROM, PAL and PLA, combinational design with PLDs, FPGA and CPLD architecture; semiconductor memory organisation, expansion and types (RAM, ROM, EPROM, EEPROM, NVRAM, SRAM, DRAM); VHDL description styles, lexical elements, data objects, attributes and operators, with combinational examples and simulation.

    Examined in the 60-mark end-semester paper, and in the mid-semester exam if it is taught by then

    • PROM, PAL and PLA
    • Designing combinational circuits with PLDs
    • CPLD and FPGA architecture
    • Semiconductor memories: RAM, ROM and their types
    • Memory organisation and expansion
    • VHDL: library, entity and architecture
    • Modelling styles and data objects
    • VHDL for gates, adders and subtractors

Unit contents are summarised from the official DBATU syllabus . AiCanCode.org is not affiliated with Dr. Babasaheb Ambedkar Technological University (DBATU).