Heat Transfer

Heat Transfer — formula sheet

Mechanical Engineering · GATE ME · SI units. Drafted with Aria, checked by the AiCanCode.org team.

Introduction to Heat Transfer

  • q = -k A (dT/dx) — Fourier’s law gives heat transfer rate q (W) by conduction; k (W/m·K), A (m²), T (K), x (m); steady 1D conduction, constant k and A.
  • q = h A (T_s - T_∞) — Newton’s law gives convective heat transfer rate q (W); h (W/m²·K), A (m²), T_s (K), T_∞ (K); external/internal convection with uniform h.
  • q = ε σ A (T^4 - T_0^4) — Stefan–Boltzmann law gives radiative heat rate q (W); ε (–), σ = 5.67×10⁻⁸ (W/m²·K⁴), A (m²), T (K), T_0 (K); diffuse-gray surface to large isothermal surroundings, nonparticipating medium.

Modes of heat transfer

  • Q_total = Q_cond + Q_conv + Q_rad — Net heat transfer rate Q_total (W) as sum of contributions; each term from respective laws; applies to combined-mode problems with appropriate interaction modeling (e.g., radiation linearization if using resistance networks).

Conduction Heat Transfer

  • q'' = -k (dT/dx) — Heat flux q'' (W/m²); k (W/m·K), T (K), x (m); 1D conduction.
  • R_cond,plane = L/(k A) — Plane-wall conduction thermal resistance R (K/W); L (m), k (W/m·K), A (m²); steady 1D, constant k.
  • R_cond,cyl = ln(r_2/r_1) / (2 π k L) — Cylindrical shell resistance R (K/W); r_1, r_2 (m), k (W/m·K), L (m); radial steady 1D, constant k.
  • R_cond,sph = (1/(4 π k)) (1/r_1 - 1/r_2) — Spherical shell resistance R (K/W); r_1, r_2 (m), k (W/m·K); radial steady 1D, constant k.
  • q'' = k (T_1 - T_2)/L — Plane wall heat flux q'' (W/m²); T_1, T_2 (K), k (W/m·K), L (m); steady 1D, no generation.
  • T(x) = T_1 + (T_2 - T_1) x/L — Linear temperature in plane wall; T(x) (K); 0 ≤ x ≤ L; steady 1D, no generation.
  • T(r) = C_1 ln r + C_2 — Cylindrical radial temperature T(r) (K); r (m); steady 1D, no generation; C_1, C_2 from BCs.
  • T(r) = - (q̇ r^2)/(4 k) + C_1 ln r + C_2 — Cylinder with uniform volumetric generation q̇ (W/m³); k (W/m·K); steady 1D.
  • T(r) = - (q̇ r^2)/(6 k) + C_1/r + C_2 — Sphere with uniform generation; symbols as above; steady 1D.
  • ∇·(k ∇T) + q̇ = ρ c_p (∂T/∂t) — General heat diffusion equation; k (W/m·K), q̇ (W/m³), ρ (kg/m³), c_p (J/kg·K), t (s); transient or steady conduction.

One-dimensional steady conduction

  • Q = (T_hot - T_cold)/ΣR — Heat rate through composite wall Q (W); ΣR is sum of series resistances (K/W); steady 1D.
  • R_conv = 1/(h A) — Convection film resistance R (K/W); h (W/m²·K), A (m²); steady.
  • R_rad,linearized = 1/(h_r A) with h_r ≈ 4 ε σ T_m^3 — Linearized radiation resistance; ε (–), σ (W/m²·K⁴), T_m (K); small ΔT about T_m.

Thermal resistance networks

  • R_total = R_1 + R_2 + … — Series addition of thermal resistances (K/W); applies when same heat rate passes through each layer.
  • 1/R_total = 1/R_1 + 1/R_2 + … — Parallel thermal paths; applies when temperature drop is common across branches.
  • R_2s,rad = (1/(A_1 ε_1)) (1 - ε_1)/ε_1 + 1/(A_1 F_{12}) + (1/(A_2 ε_2)) (1 - ε_2)/ε_2 inverted in denominator of net exchange — Two-surface diffuse-gray radiation resistance network; A_i (m²), ε_i (–), F_{12} (–); gray, diffuse, isothermal surfaces in vacuum/nonparticipating medium.

Convection Heat Transfer

  • q = h A (T_s - T_∞) — Convection heat rate q (W); h (W/m²·K), A (m²), T_s (K), T_∞ (K); external or internal convection with uniform h.
  • Re = ρ V L/μ — Reynolds number (–); ρ (kg/m³), V (m/s), L (m), μ (Pa·s); flow regime indicator.
  • Pr = ν/α = (μ c_p)/k — Prandtl number (–); ν (m²/s), α (m²/s), μ (Pa·s), c_p (J/kg·K), k (W/m·K).
  • Nu = h L/k — Nusselt number (–); h (W/m²·K), L (m), k (W/m·K); convection-conduction ratio.
  • St = h/(ρ c_p V) = Nu/(Re Pr) — Stanton number (–); links heat transfer to flow.

Forced convection

  • Nu_x = 0.332 Re_x^{1/2} Pr^{1/3} — Local over laminar flat plate; Re_x = ρ V x/μ; Pr ≥ 0.6; no pressure gradient, constant properties.
  • Nu_L = 0.664 Re_L^{1/2} Pr^{1/3} — Average over laminar flat plate length L; same constraints.
  • Nu_L = 0.037 Re_L^{0.8} Pr^{1/3} - 871 Pr^{1/3} — Average over flat plate with turbulent boundary layer and transition at Re_x,cr ≈ 5×10⁵; Pr ≈ 0.6–60.
  • Nu_D = 3.66 — Fully developed laminar flow in circular tube, constant wall temperature; Nu based on diameter D.
  • Nu_D = 4.36 — Fully developed laminar, constant heat flux wall; circular tube.
  • L_{e,h} ≈ 0.05 Re Pr D — Thermal entrance length L_{e,h} (m); Re (–), Pr (–), D (m); laminar internal flow.
  • L_{e,f} ≈ 0.05 Re D — Hydrodynamic entrance length L_{e,f} (m); laminar internal flow.
  • Nu = 0.023 Re^{0.8} Pr^{n} — Dittus–Boelter turbulent internal flow; n = 0.4 (heating fluid), 0.3 (cooling fluid); Re ≳ 10⁴, 0.7 ≤ Pr ≤ 160; smooth tubes, constant properties at T_film.
  • Nu = (f/8) (Re - 1000) Pr / [1 + 12.7 (f/8)^{1/2} (Pr^{2/3} - 1)] — Gnielinski correlation; 3×10³ ≤ Re ≤ 5×10⁶, 0.5 ≤ Pr ≤ 200; f is Darcy friction factor.
  • f ≈ 0.3164 Re^{-0.25} — Blasius smooth-tube Darcy friction factor; 4×10³ ≲ Re ≲ 10⁵.
  • Nu = 0.3 + [0.62 Re^{1/2} Pr^{1/3}] / [1 + (0.4/Pr)^{2/3}]^{1/4} · [1 + (Re/282000)^{5/8}]^{4/5} — Churchill–Bernstein for cylinder crossflow; wide Re, Pr ranges; properties at film temperature.
  • j_H = St Pr^{2/3} ≈ f/2 — Colburn analogy for turbulent flow over smooth surfaces; Pr ≈ 0.7–10.

Free convection

  • Gr = g β (T_s - T_∞) L^3 / ν^2 — Grashof number (–); g (m/s²), β (1/K), L (m), ν (m²/s); buoyancy–viscous ratio.
  • Ra = Gr Pr — Rayleigh number (–); regime indicator for natural convection.
  • Nu_L = 0.68 + 0.670 Ra_L^{1/4} / [1 + (0.492/Pr)^{9/16}]^{4/9} — Vertical plate, laminar; 10⁴ ≲ Ra_L ≲ 10⁹; constant properties at film temperature.
  • Nu_L = 0.13 Ra_L^{1/3} — Vertical plate, turbulent; 10⁹ ≲ Ra_L ≲ 10¹³.
  • Nu_D = 0.53 Ra_D^{1/4} — Horizontal cylinder, laminar; 10⁴ ≲ Ra_D ≲ 10⁹; properties at film temperature.

Thermal boundary layer

  • δ(x) ≈ 5 x / Re_x^{1/2} — Laminar velocity boundary-layer thickness δ (m) over flat plate; Re_x = ρ V x/μ; zero pressure gradient.
  • δ_t(x) ≈ δ(x) / Pr^{1/3} — Thermal boundary-layer thickness δ_t (m) for Pr ≳ 0.6; laminar flat-plate flow.

Heat Exchangers

  • Q = U A ΔT_lm — Heat rate Q (W); U (W/m²·K), A (m²), ΔT_lm (K); steady parallel/counterflow, constant U, negligible loss; correction factor F may apply.
  • ΔT_lm = (ΔT_1 - ΔT_2) / ln(ΔT_1/ΔT_2) — Log-mean temperature difference; ΔT_1, ΔT_2 (K) at each end; parallel/counterflow.
  • Q = C_h (T_{h,in} - T_{h,out}) = C_c (T_{c,out} - T_{c,in}) — Energy balance; C = ṁ c_p (W/K); ṁ (kg/s), c_p (J/kg·K).
  • ε = Q / [C_min (T_{h,in} - T_{c,in})] — Heat exchanger effectiveness ε (–); C_min (W/K).
  • NTU = U A / C_min — Number of transfer units (–); U (W/m²·K), A (m²), C_min (W/K).
  • C_r = C_min / C_max — Capacity-rate ratio (–); C_max (W/K).
  • ε_parallel = [1 - exp(-NTU (1 + C_r))] / [1 + C_r] — Parallel flow effectiveness; steady, constant properties.
  • ε_counter = [1 - exp(-NTU (1 - C_r))] / [1 - C_r exp(-NTU (1 - C_r))] — Counterflow effectiveness; steady, constant properties.
  • 1/U_o A_o = 1/(h_i A_i) + R_w + 1/(h_o A_o) + R_{f,i} + R_{f,o} — Overall resistance; U_o (W/m²·K) at outer area A_o (m²), h_i, h_o (W/m²·K), A_i, A_o (m²), R_w (K/W) wall conduction, R_{f,*} fouling (K/W).

Heat exchangers: LMTD method

  • Q = F U A ΔT_lm,ideal — Corrected LMTD with factor F (–); F from charts for multipass/crossflow; steady with specified arrangement.

Heat exchangers: NTU method

  • Q = ε C_min (T_{h,in} - T_{c,in}) — Heat rate via ε–NTU; symbols as above; steady.

Radiation Heat Transfer

  • Q = ε σ A (T_1^4 - T_2^4) — Net radiative exchange to large surroundings; ε (–), σ (W/m²·K⁴), A (m²), T_1, T_2 (K); diffuse-gray surface fully viewing isothermal surroundings, nonparticipating medium.
  • E_b = σ T^4 — Blackbody emissive power E_b (W/m²); σ (W/m²·K⁴), T (K).
  • J = ε σ T^4 + (1 - ε) G — Radiosity J (W/m²); ε (–), G irradiation (W/m²), T (K); diffuse-gray surface.
  • q'' = J - G — Net radiative heat flux at a surface q'' (W/m²); J, G (W/m²); participating media effects neglected unless G includes them.
  • ε_λ = α_λ — Kirchhoff’s law (spectral); emissivity equals absorptivity at each wavelength under thermal equilibrium; diffuse-gray if wavelength-independent.
  • λ_max T = 2.897×10^{-3} — Wien’s displacement law; λ_max (m), T (K); blackbody spectrum peak location.
  • Q_{1→2} = σ (T_1^4 - T_2^4) / [ (1 - ε_1)/(A_1 ε_1) + 1/(A_1 F_{12}) + (1 - ε_2)/(A_2 ε_2) ] — Net exchange between two finite diffuse-gray surfaces; A_i (m²), ε_i (–), F_{12} (–); vacuum/nonparticipating gas.

View factors and radiation exchange

  • Σ_j F_{ij} = 1 — Summation rule for each surface i in an enclosure; includes j = i when self-view exists.
  • A_i F_{ij} = A_j F_{ji} — Reciprocity relation; A_i, A_j (m²); diffuse surfaces.
  • F_{ii} = 0 for flat/convex surfaces; F_{ii} > 0 possible for concave surfaces — Self-view property.
  • F_{12} = 1 — Two infinitely large parallel plates facing each other; complete view.

Boiling and Condensation

  • Nu = h L/k — Definition of Nusselt number h (W/m²·K), L (m), k (W/m·K); boiling/condensation convection.
  • h̄ = 0.943 [ (ρ_l (ρ_l - ρ_v) g h_fg k_l^3) / (μ_l L ΔT) ]^{1/4} — Average film condensation coefficient on a vertical isothermal plate; h̄ (W/m²·K); ρ_l, ρ_v (kg/m³), g (m/s²), h_fg (J/kg), k_l (W/m·K), μ_l (Pa·s), L (m), ΔT (K); laminar film, negligible shear and subcooling.
  • h̄ = 0.725 [ (ρ_l (ρ_l - ρ_v) g h_fg k_l^3) / (μ_l D ΔT) ]^{1/4} — Average condensation on a single horizontal tube of diameter D (m); laminar film.
  • q''_{CHF} ≈ 0.131 ρ_v^{1/2} h_fg [ σ g (ρ_l - ρ_v) ]^{1/4} — Pool-boiling critical heat flux q''_{CHF} (W/m²); σ (N/m), g (m/s²); saturated, large horizontal surface.
  • q'' = μ_l h_fg [ g (ρ_l - ρ_v)/σ ]^{1/2} [ C_{sf} (ΔT / (h_fg Pr_l^n)) ]^3 — Rohsenow nucleate-boiling correlation; μ_l (Pa·s), Pr_l (–), C_{sf}, n empirical; saturated pool boiling on surface.

Thermal Insulation

  • q = (k A ΔT)/d — Plane-layer conduction rate q (W); k (W/m·K), A (m²), ΔT (K), d (m); steady 1D, constant k.
  • R'' = d/k — Area-specific thermal resistance R'' (m²·K/W); d (m), k (W/m·K); plane layer.
  • R = d/(k A) — Whole-layer resistance R (K/W); d (m), k (W/m·K), A (m²); plane layer.
  • r_c,cyl = k/h — Critical insulation radius for cylinder r_c (m); k (W/m·K), h (W/m²·K); external insulation with outer convection.
  • r_c,sph = 2 k/h — Critical insulation radius for sphere r_c (m); k (W/m·K), h (W/m²·K); external insulation with outer convection.

Mass Transfer

  • J = -D (dC/dx) — Fick’s law diffusive flux J (kg/m²·s); D (m²/s), C (kg/m³), x (m); 1D diffusion.
  • N = k_c (C_s - C_∞) — Convective mass flux N (kg/m²·s); k_c (m/s), C_s, C_∞ (kg/m³); same phase/basis.
  • Sh = k_c L / D — Sherwood number (–); convective mass transfer analog of Nu.
  • Sc = ν / D — Schmidt number (–); ν (m²/s), D (m²/s).
  • j_D = St_m Sc^{2/3} ≈ f/2 — Chilton–Colburn mass transfer analogy; St_m = k_c/(V), for dilute gases/liquids in turbulent flow over smooth surfaces.

Heat Transfer in Extended Surfaces

  • Q_f = η_f h A_f (T_b - T_∞) — Fin heat rate Q_f (W); η_f fin efficiency (–), h (W/m²·K), A_f (m²), T_b (K), T_∞ (K); steady, negligible radiation.
  • m = sqrt(h P/(k A_c)) — Fin parameter m (1/m); P (m), k (W/m·K), A_c (m²); straight, uniform cross-section.
  • η_f = tanh(m L)/(m L) — Fin efficiency for adiabatic tip; L (m); constant k, h; 1D fin.
  • Q_f = sqrt(h P k A_c) (T_b - T_∞) tanh(m L) — Straight fin with adiabatic tip; symbols as above.
  • η_o = 1 - (A_f/A_t) (1 - η_f) — Overall surface efficiency η_o (–); A_t total area incl. unfinned base (m²), A_f fin area (m²); uniform h, identical fins.
  • ε_f = Q_f / (h A_f (T_b - T_∞)) — Fin effectiveness ε_f (–); equals η_f for adiabatic-tip model; fins are useful if ε_f > 2.

Unsteady conduction and the lumped model

  • Bi = h L_c / k — Biot number (–); h (W/m²·K), L_c = V/A_s (m), k (W/m·K); lumped valid if Bi < 0.1.
  • Fo = α t / L_c^2 — Fourier number (–); α = k/(ρ c_p) (m²/s), t (s), L_c (m).
  • (T(t) - T_∞)/(T_i - T_∞) = exp[- (h A_s / (ρ V c_p)) t ] — Lumped-capacitance cooling/heating; A_s (m²), V (m³), ρ (kg/m³), c_p (J/kg·K); Bi < 0.1.
  • τ = ρ V c_p / (h A_s) — Time constant τ (s) for lumped systems; symbols as above.
  • T(x,t) - T_s = (T_i - T_s) erf[x / (2 √(α t))] — Semi-infinite solid suddenly brought to surface temperature T_s; x (m); constant properties.
  • q''(0,t) = k (T_s - T_i) / √(π α t) — Transient surface heat flux for step in surface temperature; k (W/m·K), α (m²/s), t (s).
  • T(0,t) - T_i = 2 q'' √(α t) / (k √π) — Semi-infinite solid with imposed constant surface heat flux q'' (W/m²); early-time approximation; constant properties.

Numerical Methods in Heat Transfer

  • (T_{i+1} - 2 T_i + T_{i-1})/Δx^2 + S/k = 0 — 1D steady conduction finite-difference node equation; S (W/m³) source term, k (W/m·K); uniform grid Δx (m).
  • Fo = α Δt / Δx^2 ≤ 0.5 — Explicit 1D transient stability criterion; Fo (–), α (m²/s), Δt (s), Δx (m).
  • T_i^{n+1} = T_i^n + Fo (T_{i+1}^n - 2 T_i^n + T_{i-1}^n) + (q̇ Δt)/(ρ c_p) — Explicit scheme update; q̇ (W/m³); uniform properties.
  • Crank–Nicolson: unconditionally stable, second-order in time — Implicit midpoint scheme for diffusion; requires solving linear system each time step.

Heat Transfer in Turbulent Flow

  • Nu = 0.023 Re^{0.8} Pr^{n} — Dittus–Boelter; n per heating/cooling; smooth tubes.
  • Nu = (f/8) (Re - 1000) Pr / [1 + 12.7 (f/8)^{1/2} (Pr^{2/3} - 1)] — Gnielinski; 3×10³–5×10⁶.
  • f ≈ 0.3164 Re^{-0.25} — Blasius Darcy friction factor; smooth tubes, 4×10³–10⁵.
  • j_H = St Pr^{2/3} ≈ f/2 — Colburn analogy; smooth turbulent flows, moderate Pr.

Heat Transfer in Laminar Flow

  • Nu_D = 3.66 — Fully developed, constant wall temperature, circular tube.
  • Nu_D = 4.36 — Fully developed, constant heat flux, circular tube.
  • Gz = Re Pr D / L — Graetz number (–); D (m), L (m); entrance region characterization.
  • L_{e,f} ≈ 0.05 Re D, L_{e,h} ≈ 0.05 Re Pr D — Entrance lengths (m) hydrodynamic/thermal; laminar tubes.

Heat Transfer in Porous Media

  • u = - (K/μ) ∇p — Darcy’s law; superficial velocity u (m/s), permeability K (m²), μ (Pa·s), pressure p (Pa); slow flow in porous matrix.
  • q'' = -k_eff (dT/dx) — Effective conduction flux q'' (W/m²); k_eff (W/m·K); saturated porous matrix.
  • Ra* = (g β (T_h - T_c) K L)/(α ν) — Modified Rayleigh number for porous media (–); K (m²), L (m), α (m²/s), ν (m²/s); onset of convection.

Heat Transfer in Micro and Nano Scales

  • Kn = λ/L — Knudsen number (–); λ mean free path (m), L characteristic length (m); rarefaction assessment, slip/transition regimes.

Heat Transfer Enhancement Techniques

  • Φ_h = h_enh / h_base — Heat transfer augmentation ratio Φ_h (–); h_enh, h_base (W/m²·K); compares enhanced to baseline surfaces under comparable conditions.
  • (UA)_{enh} / (UA)_{base} — Overall conductance augmentation (–); U (W/m²·K), A (m²); system-level comparison at same flow/fluids.

Thermal Radiation in Participating Media

  • I(s) = I_0 e^{-κ s} — Beer–Lambert absorption in a nonemitting, nonscattering medium; intensity I (W/m²·sr), path s (m), absorption coefficient κ (1/m).
  • τ = κ L — Optical thickness τ (–); κ (1/m), L (m).
  • q_rad = - (16 σ T^3 / (3 κ_R)) (dT/dx) — Rosseland diffusion approximation; κ_R Rosseland mean absorption (1/m), σ (W/m²·K⁴), T (K); optically thick, near-isotropic radiation field.

Heat Transfer in Biological Systems

  • ρ c ∂T/∂t = ∇·(k ∇T) + ω_b ρ_b c_b (T_a - T) + q̇_{met} + q̇_{ext} — Pennes bioheat equation; ρ, c tissue density (kg/m³), specific heat (J/kg·K), k (W/m·K), ω_b blood perfusion (1/s), ρ_b (kg/m³), c_b (J/kg·K), T_a arterial blood temp (K), q̇_{met} metabolic (W/m³), q̇_{ext} external (W/m³); living tissues, continuum assumption.