First Year Engineering is coming soon

We're still writing and reviewing the notes for every subject, and we'll open it when every subject is ready. Meanwhile you can practise aptitude, ask Aria about any subject, or see the branches that are ready.

Errors and approximations

Errors and approximations: types and sources of error, significant figures and rounding, absolute/relative/percentage error, limits of accuracy, error propagation (sum, difference, product, quotient, powers; multivariable via differentials), truncation error in series, and practical estimation of er

Drafted with Aria, reviewed by the AiCanCode.org team · Updated . How we write and check our notes. Spotted an error? Use Give Feedback at the bottom of the page.

Why it matters

Engineers rarely know a “true value.” Every measurement and every computed result has some error. Understanding errors and approximations helps you decide how many significant figures to keep, how much trust to place in a result, and how measurement errors affect a final design calculation (like stress, flow rate, or power).

Key ideas

  • Error: The difference between the true value T and approximate value A. Two common measures:
    • Absolute error: |T − A|. Non-negative.
    • Relative error: |T − A| / |T|, a ratio showing error size compared to the true value.
    • Percentage error: Relative error × 100%.
  • Accuracy vs precision:
    • Accuracy: How close a value is to the true value.
    • Precision: How fine the resolution or repeatability is (e.g., measured to nearest 0.01 mm). High precision does not guarantee accuracy.
  • Significant figures (sig. figs.): Digits that carry meaningful information about precision. Rules used in exams:
    • All non-zero digits are significant.
    • Zeros between non-zero digits are significant (e.g., 1003 has 4 sig. figs.).
    • Leading zeros are not significant (e.g., 0.00450 has 3 sig. figs.).
    • Trailing zeros are significant only if there is a decimal point (e.g., 1500 has 2, but 1500. has 4 sig. figs.).
  • Rounding rule: To round at a digit, look at the next digit. If it is 5 or more, increase the last kept digit by 1; otherwise leave it. (If your university specifies round-half-even, follow that. Here we assume “round-half-up.”)
  • Types of errors:
    • Gross errors: Mistakes by human/reading/recording.
    • Systematic errors: Consistent bias due to instrument calibration, observation method, or environment.
    • Random errors: Unpredictable variations with zero mean, analyzed statistically.
  • Limits of accuracy (instrument resolution): If a quantity x is measured to the nearest unit u (e.g., 0.01 m), then the measurement x̄ is within ±(u/2) of the true x, i.e., |x − x̄| ≤ u/2. This bound is also called the maximum possible error.
  • Propagation of errors (single-variable functions): If y = f(x) and x has a small absolute error Δx, then the approximate absolute error in y is
    • Δy ≈ |f′(x)| · Δx. The approximate relative error is |Δy|/|y| ≈ |f′(x)|·|Δx|/|f(x)|.
    • This comes from the differential dy = f′(x) dx (first-order Taylor approximation).
  • Propagation of errors (several variables): If y = f(x₁, x₂, …, xₙ) and each xᵢ has small error Δxᵢ, then the first-order absolute error bound is
    • |Δy| ≤ |∂f/∂x₁|Δx₁ + |∂f/∂x₂|Δx₂ + … + |∂f/∂xₙ|Δxₙ.
    • For relative error, divide the above by |y| (when y ≠ 0).
  • Common propagation shortcuts (first-order, worst-case):
    • Sum/difference: z = x ± y → Δz ≤ Δx + Δy.
    • Product/quotient: z = x·y or x/y → Δz/|z| ≤ Δx/|x| + Δy/|y|.
    • Power: z = xⁿ → Δz/|z| ≤ |n|·(Δx/|x|).
  • Truncation error: Error due to cutting off an infinite process (e.g., Taylor series, numerical method). If f(x) has a Taylor series, truncating after k terms leaves a remainder Rₖ₊₁(x). For small x or sufficiently many terms, Rₖ₊₁ can be bounded by a known formula.
  • Bias vs uncertainty:
    • Bias: Systematic shift from the true value (e.g., uncalibrated instrument). Reduces accuracy even if repeated many times.
    • Uncertainty: Range of probable values due to unknown errors; reported as ± bound.
  • Diagram to draw for differentials (if asked): Draw the curve y = f(x). At a point x, draw the tangent line. Show a small horizontal change Δx and the corresponding vertical change along the tangent f′(x)Δx as the linear approximation to the actual change in y. Label dy ≈ Δy.
  • Diagram to draw for random errors (if asked): Draw a bell-shaped curve (normal distribution) centered at the true value T. Shade the central band to show most repeated measurements cluster near T; label mean, standard deviation σ, and indicate that random errors spread measurements around T.

Exact statements commonly asked:

  • Definition: “Absolute error is the magnitude of the difference between the true value T and approximate value A, i.e., |T − A|.”
  • Definition: “Relative error is the ratio of absolute error to the magnitude of the true value, i.e., |T − A|/|T|.”
  • Statement (limits of accuracy): “If a measurement is recorded to the nearest u, the maximum possible error is u/2.”
  • Proposition (first-order error propagation): “If y = f(x₁, …, xₙ) and the errors are small, the maximum absolute error in y is bounded by the sum of the absolute values of the first-order partial derivatives times the respective absolute errors.” Derivation sketch:
    1. Taylor-expand: f(x + Δx) ≈ f(x) + ∑(∂f/∂xᵢ)Δxᵢ.
    2. Take absolute values and apply triangle inequality: |Δy| = |∑(∂f/∂xᵢ)Δxᵢ| ≤ ∑|∂f/∂xᵢ|·|Δxᵢ|.
    3. Divide by |f(x)| (if nonzero) for relative error.
  • Rule (products/quotients/powers) follow by applying the above to f(x) = ln z = ln x + ln y, etc., or by direct differentials: d(ln z) = dz/z = dx/x + dy/y; for z = xⁿ, dz/z = n·dx/x.

Formulas

  • Percentage error = (|T − A| / |T|) × 100% — Unitless percent. Applies when T ≠ 0.
  • Maximum possible error = u / 2 — u: measurement resolution (SI unit of quantity). Applies for “measured to the nearest u.”
  • dy ≈ f′(x)·dx — y = f(x), dx: absolute error in x (SI unit of x), dy: absolute error in y (SI unit of y). First-order approximation for small dx.
  • |Δy| ≤ |∂f/∂x₁|Δx₁ + |∂f/∂x₂|Δx₂ + … + |∂f/∂xₙ|Δxₙ — y = f(x₁,…,xₙ). Small errors; first-order worst-case bound.
  • Sum/difference: Δz ≤ Δx + Δy — z = x ± y. Δx, Δy absolute error bounds.
  • Product/quotient: Δz/|z| ≤ Δx/|x| + Δy/|y| — z = x·y or z = x/y, x ≠ 0, y ≠ 0.
  • Power: Δz/|z| ≤ |n| · (Δx/|x|) — z = xⁿ, x ≠ 0.
  • d(ln z) = dz/z — Useful for deriving relative error rules.
  • Sphere volume: V = (4/3)·π·r³ — r in m; V in m³. For error: dV = 4·π·r²·dr and ΔV/V ≈ 3·(Δr/r).
  • Taylor remainder bound (Maclaurin): |Rₙ₊₁(x)| ≤ (M·|x|ⁿ⁺¹)/(n+1)! — M is a bound on |f⁽ⁿ⁺¹⁾(ξ)| for ξ between 0 and x. Applies to smooth functions near 0.

Worked examples

  1. Limits of accuracy and propagation (square of a length) Given: A square plate has side measured as L = 2.368 m to the nearest millimetre (0.001 m). Find the maximum possible error in area A = L² and the percentage error.

Steps:

  1. Resolution u = 0.001 m → Maximum possible error in length ΔL = u/2 = 0.0005 m.
  2. Area formula: A = L². Differential: dA = 2L·dL.
  3. Maximum absolute error (first-order): ΔA ≈ 2·L·ΔL = 2 × 2.368 m × 0.0005 m = 0.002368 m².
  4. Approximate area using measured L: A ≈ (2.368 m)² = 5.607424 m².
  5. Percentage error ≈ (ΔA/A) × 100% = (0.002368 / 5.607424) × 100% ≈ 0.04226%.

Answer: Maximum absolute error in area ≈ 0.002368 m²; percentage error ≈ 0.0423% (first-order).

  1. Error in computed quantity from product and quotient Given: Length L = 3.26 m measured to nearest 0.01 m; Width W = 4.1 m to nearest 0.1 m; Time t = 2.03 s to nearest 0.01 s. Compute Q = (L·W)/t and its maximum percentage error.

Steps:

  1. Maximum possible errors: ΔL = 0.005 m; ΔW = 0.05 m; Δt = 0.005 s.
  2. Compute Q using measured values:
    • Numerator: L·W = 3.26 m × 4.1 m = 13.366 m².
    • Q = 13.366 m² / 2.03 s ≈ 6.5842 m²·s⁻¹.
  3. Relative error bound (first-order): ΔQ/|Q| ≤ ΔL/|L| + ΔW/|W| + Δt/|t| = (0.005/3.26) + (0.05/4.1) + (0.005/2.03) ≈ 0.001533 + 0.012195 + 0.002463 = 0.016191.
  4. Percentage error bound ≈ 0.016191 × 100% ≈ 1.619%.
  5. Absolute error bound in Q: ΔQ ≤ 0.016191 × 6.5842 m²·s⁻¹ ≈ 0.1066 m²·s⁻¹.

Answer: Q ≈ 6.584 m²·s⁻¹ with maximum percentage error ≈ 1.62% (absolute error about ±0.107 m²·s⁻¹).

  1. Error in volume of a sphere from radius measurement Given: Radius r = 6.00 cm measured to nearest 0.01 cm. Find the maximum absolute and percentage errors in volume V.

Convert to SI: r = 0.0600 m; resolution u = 0.0001 m → Δr = u/2 = 0.00005 m.

Steps:

  1. V = (4/3)πr³; differential: dV = 4πr²dr.
  2. Absolute error (first-order): ΔV ≈ 4πr²Δr = 4π × (0.0600 m)² × 0.00005 m = 4π × 0.0036 m² × 0.00005 m = 4π × 1.8×10⁻⁷ m³ ≈ 2.26195×10⁻⁶ m³.
  3. Compute V using measured r: V ≈ (4/3)π × (0.0600 m)³ = 4.18879 × 2.16×10⁻⁴ m³ ≈ 9.04778×10⁻⁴ m³.
  4. Percentage error ≈ (ΔV/V) × 100% ≈ (2.26195×10⁻⁶ / 9.04778×10⁻⁴) × 100% ≈ 0.25%.

Answer: Maximum absolute error ≈ 2.262×10⁻⁶ m³; percentage error ≈ 0.25% (first-order).

  1. Truncation error using Taylor (Maclaurin) series Approximate sin x at x = 0.3 rad using 3-term Maclaurin polynomial and bound the error.

Steps:

  1. Maclaurin series: sin x = x − x³/3! + x⁵/5! − … . Truncate after x − x³/3!.
  2. Approximation: T₃(x) = x − x³/6. For x = 0.3, T₃(0.3) = 0.3 − 0.027/6 = 0.3 − 0.0045 = 0.2955.
  3. Remainder bound: Next term magnitude ≤ |x|⁵/5! = 0.3⁵/120 = 0.00243/120 ≈ 2.025×10⁻⁵.
  4. True sin(0.3) ≈ 0.2955202067 (for checking). Actual error ≈ |0.2955202067 − 0.2955| ≈ 2.0207×10⁻⁵, within the bound.
  5. Percentage error ≈ (2.0207×10⁻⁵ / 0.2955202067) × 100% ≈ 0.00684%.

Answer: sin(0.3) ≈ 0.2955 with truncation error bounded by about 2.03×10⁻⁵ (≈0.0068%).

Common mistakes

  • Dropping units mid-calculation; always carry SI units through every step.
  • Over-rounding intermediate results; round only at the end to the correct significant figures.
  • Using sum/difference error rules for products/quotients or vice versa. Remember: for products/quotients, relative errors add; for sums/differences, absolute errors add.
  • Ignoring sign when combining errors; bounds use magnitudes (worst case), so use absolute values.
  • Applying first-order approximations for large errors; these rules assume small errors (linearization valid). For large uncertainties, higher-order terms may matter.
  • Confusing precision with accuracy; many correct decimal places do not guarantee correctness if there is bias.

For your exam

  • Derivations: First-order propagation via differentials (single and multivariable); relative error for product/quotient/power using logarithmic differentiation; Taylor remainder bound statement.
  • Numericals: Compute maximum possible error from instrument resolution; propagate errors in formulas (area, volume, density, flow, power); percentage error of functions like xⁿ, sin x, etc., using differentials; truncation error in series approximations with remainder bounds.
  • Diagrams: Tangent-line approximation for dy ≈ f′(x)dx; bell-curve sketch for random errors; symmetric interval around a measured value showing ±u/2.
  • Full-marks answers include: clear formula before substitution, correct units, correctly halved resolution for maximum error, correct use of absolute vs relative error, clean rounding at the end, and a brief justification (“using first-order approximation” or “using product relative error rule”).

Quick check

  1. A length is recorded as 12.34 cm to the nearest 0.01 cm. What is the maximum possible error and the relative error bound?
  2. If z = x³ and x has a relative error of 0.4%, what is the approximate relative error in z?
  3. Using T₃(x) = x − x³/6 to approximate sin x at x = 0.2 rad, give a bound on the truncation error using the next term.

Answers: (1) ΔL = 0.005 cm; relative error bound ≈ 0.005/12.34 ≈ 0.000405 (0.0405%). (2) ≈ 3 × 0.4% = 1.2%. (3) Next term magnitude ≤ x⁵/5! = 0.2⁵/120 = 0.00032/120 ≈ 2.667×10⁻⁶.

Finished this topic? Mark it so your progress, study plan and readiness keep up.

Stuck on something here?